Question about 1997 Chrysler Town & Country

1 Answer

Our car will die sometimes in the morning and restart when we let it set for a little bit , then run all day for a few days and then does it again. Its just like a kill switch and just kills it .

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

We have had this problem as well. Chrysler is well aware of the issue. It is the instrument cluster behind the dash. Don't let them tell you it's the Body Control Module...it's not. If you bang on the dash just above the guage cluster, it will usually start or simply unhook your battery and let it sit for a bit and it should start after the alarm resets. It's a 15 minute fix to take the dash off and replace that instrument cluster. We paid WAY more money to have the BCM replaced and it didn't fix it and the dealership refused to refund us and fix the right thing without charging us more.

Posted on Aug 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car will run fine and then suddently die. I had it towed and the mechanic told me the next day that it was running fine and that I would be able to drive it. After driving to a couple of stores...


if no codes fuel pump , fuel pump relay,,fuel filter,,====cat converter clogging egr valve carboned up ---these are some problems that sometimes will stall and allow vehicle to restart with out setting off a code

May 04, 2017 | 1997 Oldsmobile 88

1 Answer

2004 SRX - Sputtering, Stalling and Start issues


Have them check the camshaft/crankshaft sensor.. please indicate if my solutions are helpful thankyou

Apr 28, 2013 | 2004 Cadillac SRX

2 Answers

1990 Chevy Cavalier z24 shuts off and has trouble starting


sounds like a possble bad egr valve stcking open or then clutch in the torque converter is staying on

Aug 10, 2012 | Chevrolet Cars & Trucks

2 Answers

Just turns off on it's own, Wait 60 sec. restart press pedel it dies.


This engine is electronically controlled so the first thing that must be done here is to have the systems control computer tested for fault codes and then do the proper diagnostics based on those codes.

Jun 07, 2012 | 1995 Plymouth Voyager

1 Answer

Good morning! My 1990 Toyota Corolla 2 Door Sedan has been fine until the past 3 days. The car starts fine then several minutes after driving the car will die. I pull over on the side of the road, put it...


this may be a few things, the most common is a bad ignition coil,this looses spark and car dies, then after cranking a few times it will start to work again, the problem can also be a fuelpump doing the same thing, the best thing would be to check for spark when it dies but you would need someone to spin the engine while you were to see if the sparkplug wire was sparking,another common thing is the distributor itself or the cap, see this can go on and on without a good diagnoses you can throw parts at this car all day, it would be cheaper to have someone test it, they would need to drive it until it stalled and then do some quick testing before it started and this may take a few days because you said after a few times it will run fine,

Dec 10, 2010 | 1990 Toyota Corolla

2 Answers

Engine quits and won't restart


Very possible it may be control module. If you have no engine codes, than you can rule out any sensors. Usually if anything electrical is going out, it will set off engine codes. Have you replaced the fuel pump relay? Checked all vaccum hoses, check compression for gasket leaks?

May 04, 2009 | 2000 Suzuki Grand Vitara

2 Answers

I have a 1991 jeep wrangler with a new fuel pump and relay.


Check spark and fuel pressure. One is failing and must determine which to proceed further.

Apr 03, 2009 | 1991 Jeep Wrangler

Not finding what you are looking for?
1997 Chrysler Town & Country Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...