Question about 1987 Nissan Pulsar

1 Answer

Where is the camshaft position sensor located on the 1987 Nissan Pulsar NX with 1.6L motor?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 20 Answers

There is no camshaft sensor!!!

Posted on Aug 21, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a nissan murano 2005 with the code p1701 and a p0340 how can i use them to repair these codes


Nissan Murano P0340 2005 Nissan Murano - Camshaft Position Sensor Circuit
Possible causes- Faulty Camshaft Position Sensor-
Camshaft Position Sensor harness is open or shorted- Camshaft Position Sensor circuit poor electrical connection- Faulty starter motor- Starting system circuit-
Dead (Weak) battery
P1701- Fuel trim

I would suggest replacing the camshaft position sensor. When the sensor fails it can cause changes in fuel system that the computer can detect. So I suspect once the camshaft sensor ivreplaced that the P1701 code will be gone.
Cam Position Sensor Replacement Nissan Murano 3 5L

Sep 20, 2015 | Nissan Cars & Trucks

1 Answer

Where is the coil pack located at on a 1987 Nissan Pulsar. Also spark plugs been changed car still not starting


The link will show you what it looks like. If you follow the leads back from the spark plugs, that will take you to the distributor 9a circular cap with 5 wires). In the centre of the distributer, there is a single lead, follow that one and it will take you to the ignition coil. 1987 Nissan Pulsar NX Ignition Coil Hitachi

Sep 19, 2015 | Nissan Cars & Trucks

1 Answer

1988 nissan pulsar nx idles rough


The Pulsar starter is located centrally, underneath the engine close to the passenger compartment."According to my car, the E16i engine, it is on the drivers side of the engine below/behind the distributor.


Performance chips of BMW.

May 31, 2012 | 1988 Nissan Pulsar

1 Answer

Fuel pressure regulator for nissan nx se 1987. Where is is located its not on the fuel rail. Ive looked, ordered the new one due to the fact its the only thing that could be causing the problem.


Sit on the end of the fuel rail, where the injector's are at, is held on with three small bolt's, that's on fuel injection engine's, if it's a carburetor engine, don't have fuel regulator.

Sep 24, 2010 | 1987 Nissan Pulsar

1 Answer

I have a 1987 Nissan Pulsar NX. the problem is, when I try to shift into reverse, it grinds pretty bad. I tried adjusting the clutch rod but it didn't help. Do you have any ideas? Thank you.


I thought these had a hydraulic clutch. Bleed it at the slave cylinder. Its a bleeder screw just like on the brakes. Takes two people

Aug 13, 2010 | 1987 Nissan Pulsar

1 Answer

83 nissan pulsar NX


Check he mas air flow censor, 02 censor and the throttle position sencer. Assuming you have done all the required maintenance on the vehicle like the air filter, oil, spark plugs, wires, cap and roter.

Feb 08, 2010 | 1983 Nissan Pulsar

1 Answer

My friend recently got a nissan 87 pulsar nx, but doesn't have a manual for it... where would a person get one of these?


Your local auto parts store can get you the repair manual. As far a an owners manual, possibly from the Nissan dealer, or there are some available online.

Nov 08, 2009 | 1987 Nissan Pulsar

1 Answer

1987 nissan pulsar won't start


YOU GOT THE TIMING OFF ON THE TIMING BELT BY HALF  TURN.                                                    GOOD LUCK!

May 28, 2009 | 1987 Nissan Pulsar

1 Answer

Where crank shaft and camshaft?


The camshaft position sensor is located on the timing cover, near the top of the motor. The crankshaft position sensor is located on the same timing cover near the crankshaft. Just a side note, more than likely the crankshaft position is your issue and it's under a recall from Nissan and they will replace it for free.

May 23, 2009 | 2002 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...