Question about 2004 Hyundai XG350

1 Answer

How do you replace the starter on a 2004 Hyundai XG350L?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

Step 1. Disconnect the negative battery cable.
Step 2. Remove the heat shield protecting the starter from the heat of the LH exhaust manifold
Step 3. Disconnect the wire to the starter solenoid
Step 4. Disconnect the battery cable at the starter (12mm nut)
Step 5. Remove the two 14mm bolts which attact the starter to the transmission bell housing & remove the starter.
Reassembly is in reverse order.

Posted on Oct 10, 2010

  • Paul McGrath
    Paul McGrath Oct 10, 2010

    Overlooked the possibility the fasteners which mount the starter to the bell housing might be one 14mm nut & one 14mm bolt.

  • hoppergs Jan 02, 2011

    Is the starter best accessed from the bottom of the car?

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: I need 2004 Hyundai XG350L Service/repair Manual

3.5L Engine

Remove or disconnect the following:

  1. Negative battery cable
  • Engine coolant
  • Water pump pulley bolts
  • Alternator bolt, loosen only
  • Water pump pulley and drive belts
  • Crankshaft pulley
  • Timing belt cover(s)
  1. Turn the crankshaft until the timing marks on the camshaft sprocket and cylinder head are aligned.
  2. Loosen the timing belt tensioner bolt and turn the tensioner counterclockwise as far as it will go. Tighten the adjusting bolt.
  3. Mark the timing belt with an arrow showing direction of rotation.
  4. Remove the timing belt.
  5. If defective, remove the timing belt tensioner.

9767b45.gif
Timing belt sprocket alignment mark positioning for belt removal and installation—3.5L engine

To install:
  1. If necessary, install the timing belt tensioner.
  2. Attach the top of the tensioner spring on the engine coolant pump pin. Ensure the hook on the pin is facing down and the hook on the tensioner is facing away from the engine
  3. Rotate the timing belt tensioner to the extreme counterclockwise position. Temporarily lock the tensioner in place.
  4. Align the timing marks of the camshaft and crankshaft sprockets.
  5. Install the timing belt on the crankshaft sprocket, then onto the rear camshaft sprocket.
  6. Route the belt to the coolant pump pulley, the front camshaft sprocket and the timing belt tensioner.
  7. Apply force counterclockwise to the rear camshaft sprocket with tension on the tight side of the belt and check that timing marks are aligned.
  8. Loosen the tensioner bolt 1–2 turns and tighten the timing belt to a tension of 57–84 lbs. (260–380 N).
  9. Turn the crankshaft two turns clockwise.
  10. Readjust the sprocket timing marks and tighten the tensioner bolts.
  11. Install the timing belt covers.
  12. Install the crankshaft pulley and tighten to 108–116 ft. lbs. (150–160 Nm).
  13. Install or connect the following:
    • Timing belt cover(s)
    • Crankshaft pulley
    • A/C compressor belt
    • Water pump pulley
    • V belt
    • Negative battery cable
    • Engine with coolant

Posted on Feb 10, 2010

  • 94 Answers

SOURCE: How to replace 2004 Hyundai Elantra starter

First, disconnect the battery. Then the only part that needs to be removed to access the starter is the rubber air plenum boot between the throttle body and the air filter housing. This allows enough room to get an arm in there to access the 14mm bolts that attach the starter to the transmission. After removing the bolts, the starter can be removed from underneath the car. lower it down as much as possible, and unbolt the power cable. You may have to twist and turn it a bit to get around the support between the engine block and intake manifold, but it will come out.

Posted on Feb 07, 2010

  • 24 Answers

SOURCE: 2005 Hyundai XG350L Fuel Filter

Hi there, 
If you can get under the car just head to the petrol tank and look for the lines running to and from the tank,
There should be several thin copper looking metal tubes running from the tank to the engine bay,
Generally somehwere along that line should be the fuel canister that should look almost the same as your new one, 
Its then a simple process of unscrewing the old one and screwing in the new one, Be aware not to use any sort of flame light ie lighter when under there as fuel will run out when you remove the old one. If its not under ther then it will be mounted in the engine bayas before just follow those tubes.
You may need to turn the igition on and off a few times once installed to prime the lines if the car does not automatically do this.
If it still wont start try pumping the gas/accelerator once or twice,
Be carefull not to flood the car and you should be away.
Hope this helps
Cheers
Steve

Posted on Apr 03, 2009

menard892000
  • 16 Answers

SOURCE: how do I change the cabin filters on a 2004

you will need a phillips screw driver and pliers. now first open the glove box and remove the clamps on etch side on the inside that stops the glove box from falling out then remove the screws from the inside top edge bottom right then remove the bolts at the bottom remove the glove box then look for a vertical door lift from the bottom and remove this peace then take out your air filter. I KNOW THIS IS A LOT SO IF YOU NEED ME TO POST A YOUTUBE VID JUST LET ME KNOW

Posted on Mar 19, 2010

  • 1915 Answers

SOURCE: How can I adjust the

You can not adjust rpm's, it is controlled by the engine computer. if you idle is not right, either your throttle position sensor is not right, or your idle air control is malfunctioning, although there can be numerous other causes for erratic idle (vacuum leaks, throttle body or air filter needs servicing, etc.).

Posted on May 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What may cause my 2004 hyundai xg350l to over heat?


1. Stuck thermostat
2. Low on coolant
3. bad water pump..

(#1 is best bet). .. FLUSH entire system when replacing the thermostat... check the hoses for wear..(they wear out from the inside.. look for bubbling, cracking, being soft inside.....replace if any questions...(not fun being stuck because of a $10 hose..!!!)

http://www.hyundai-forums.com/grandeur.../111323-please-help-where-my-thermostat.htm..
Hyundai XG350 Thermostat
Upper Lower Radiator Hoses Thermostat Replacement Hyundai Tiburon 2001 2008

Jul 14, 2017 | Hyundai Cars & Trucks

1 Answer

2004 Hyundai xg350L inertia fuel control switch location?


Vehicle handbook should provide the location which is often either under the bonnet close to the bulkhead or behind one of the front footwell kick panels.
When the switches were first introduced the spare wheel well was used.

Mar 23, 2017 | 2004 Hyundai XG350

1 Answer

2004 Hyundai xg350. Wipers quit working. What steps do i take to see if its a motor or fuse etc.?


Search Results

    02 XG350 air, sunroof, seat warmers, and intermittent wipers quit ...

    www.hyundai-forums.com/.../149142-02-xg350-air-sunroof-seat-warme...

    Sep 27, 2012 - 9 posts - ‎5 authors
    An automotive shop pulled up the car and said their was a fuse box with a lot of relays in it on the passenger compartment .... 2004 XG350L .... Same thing happened to me, 2002 XG350, sunroof, blower, vanity light all out.

    Hyundai XG350 wipers not working Questions & Answers ...

    www.fixya.com > ... > wipers not working > Cars & Trucks > Hyundai
    Hyundai XG350 cars & trucks wipers not working questions and answers. Ask your Hyundai wipers not working related question. ... 2004 Hyundai XG350.

    Hyundai wipers not working Questions & Answers - Fixya

Dec 03, 2015 | Hyundai Cars & Trucks

1 Answer

Replace drive belts on a xg350l 2004


Go to www.hmaservice.com and register your vehicle by VIN #.. you'll then have access to wiring diagrams, shop manuals, service bulletins, illustrations and procedures, etc.

Sep 01, 2011 | Hyundai XG350 Cars & Trucks

1 Answer

How can I adjust the rpm's on a 2004 Hyundai XG350L


You can not adjust rpm's, it is controlled by the engine computer. if you idle is not right, either your throttle position sensor is not right, or your idle air control is malfunctioning, although there can be numerous other causes for erratic idle (vacuum leaks, throttle body or air filter needs servicing, etc.).

May 23, 2011 | 2004 Hyundai XG350

1 Answer

What grade oil should I use for my 2004 hyundai xg350L? Also would it be better to use a synthetic blend?


5w30, drain all your oil and change filter before upgrading to full or a synthetic blend. Car runs better and longer before changes on full synth.

Aug 26, 2010 | 2004 Hyundai XG350

1 Answer

2004 Hyundai XG350L


no it sounds like you need to replace it because i had the same problem and checked the fuse but that did not work so i just replaced it the sell them at walmart for about $10.00

Jan 11, 2009 | 2004 Hyundai XG350

Not finding what you are looking for?
2004 Hyundai XG350 Logo

Related Topics:

722 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...