Question about 1993 Plymouth Voyager

2 Answers

Front left wiper works, right wiper stopped working? 1 motor or 2?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 560 Answers

One motor with a linkage. So could be one of 2 things.

1. Arm not tight enough on spindle, remove Black cap to expose the nut and tighten

2. Lingage failled, remove scuttle panels to expose linkage, you will see a bar has dropped off, sometime they will clip back together but on occaision it may need to be re-newed.

Regard

Lloyd

Posted on Aug 21, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 22,156 Answers

The nut on the end of the wiper arm has come loose

Posted on Aug 21, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Wiper issues only work on high but work very slow


with engine running and not.?
front or rear wiper,?????
toss dice, land on front......( 50/50 odds)
it's a network now, no more old style, point to point one wire for every thing on car and a ton of copper to match.
first test all fuses, then scan it.
or it will get expensive fast guessing.
the Switch bank brain under the wiper stalk
sends what you did, on to the LIN bus network,
The switch there does not actually drive lamps.
its just a digital switch, (some are 3 level logic)
The switches on some use a bank of internal resistors to tell the switch bank what you did.

this LIN data stream, is sent to the cluster brain
and also to the TIPM brain.(Allen Turing brains)
the cluster responds for many actions, taken and shows you what you did (EG) for blinkers, flashes the cluster TURN lamp. in same.
Wipers front.
the command for wipers are sent to the TIPM
this device, runs (DRIVES) a huge number of things on the car. (ask for schematics, I have it in pdf forum now,)
Totally Integrated power module. or TIPM
It drives the wiper motor using internal high powered electronics. Direct drive,..
It also senses the wipers location called the sense wire.
The TIPM brain, has complex logic to do all that
it gets many commands to do, (fast ,slow, intermittent wipe) and via TIPM computer memory instructions,
does the job.with pure software. inside.
the wipers can fail for many reasons besides simple mechanical jam or a cut wire.
1: fuse blown to any of those module. check them all if you are SAVVY!
2: TIPM bad,
3: TIPM power supply pin too low, say car battery is 10v ( are head lamps dim,, hummmmmmmmmm)
4: TIPM programming bad. (scrambled brain, needs re-flash)
5: CAN bus or LIN bus, noise, or gross collisions of data on that vital bus. (only scans work here)

IF all fuses are good we scan it .
as always , we check battery voltage first.
with out fail, and listening to the starter motor.
if the starter is dead or weak , we want a strong battery to make all this complex electronics in the car work.
A $10 voltmeter and you know know, battery is above 12.6vdc rested, key on, engine off.
start engine and it goes above, 13.3vdc.
That same tool i can test all fuse. ask.
end comments.

FSM page:
the first page states (QUOTE)
The most reliable, efficient, and accurate means to diagnose the front wiper motor or the electronic controls and communication related to front wiper motor operation requires the use of a diagnostic scan tool. Refer to the appropriate diagnostic information.
NOTE The front wiper and washer switches are integral to the right multi-function switch. The right multi-function switch is hard wired to the left multi-function switch/Steering Control Module (SCM), which communicates with the ElectroMechanical Instrument Cluster (EMIC)/Cab Compartment Node (CCN) over the Local Interface Network (LIN) data bus.
Before performing any of the following tests, determine whether the other functions of the right and left multi-function switch/SCM are operational. If only the right multi-function switch functions are inoperative, test and repair the right multi-function switch or the jumper harness between the right and left multi-function switches before attempting to repair the Front Wiper and Washer System. If both the right and left multi-function switch/SCM functions are ineffective, diagnose and repair that problem before attempting to repair the Front Wiper and Washer System. end quotes.


what's MORE?
what is missing is a block diagram, here ill make one so we can all learn....


Binary switch stalk. via 7 pin connector.
to:
SCM module (steering control module)
to: (i guess the SCM is the Bank switch brain)
the LIN>CAN network, (the SCM sends digital commands to)
to:

if you scan it and see errors from SCM to TIPM
that needs to be corrected first.
garbled bus data will make the TIPM go nuts.

That ground bad theory fails. because...
the motor uses Ground G112
if that wire fails you get vast numbers of failure from 10 majors. including oxygen sensor 1/2
so it;'s not G112 bad.
the motor has fast winding and low speed.
and a common ground. and a sense wire.

never skip scanning the car, or its all like a dog chasing his tail.
Battery not discharged, (you never said car runs)
fuses all good, (means tested)
scanned and not DTC errors. (i bet yes errors)
there 7 pages for the whole can/lin bus.

but this one is switch banks.
one tricky aspect of this, is the cluster
I think translates this wiper data commands from the LIN bus and then rebroadcasts to to the CAN-BUS. that he TIPM uses.that means.
so error are both buses are important.
this is the LIN-bus, the cluster retransmites the commands do the CAN-BUS. so if cluster is dead
that kills those commands,... out.bound. see?
tricky, i told you.

acb4a86e-6ebf-49e6-b000-a843e7e1804e.jpg

Apr 14, 2016 | 2007 Jeep Compass 2.4

1 Answer

I need a fuse box diagram for a 1985 1.3 Opel Kadett Cub


I found these on a site I'm assuming they're in order from number 1
Layout Diagram Parts: Direction signal lamps, Right tail lamp, license plate lamp, instrument lights, Left tail lamp, Interior lamp, Heater motor, stop lights, Horn, windshield wiper
if the fuse is good and the wires are not broken or disconnected it may be the wiper motor is bad

Feb 18, 2015 | Opel Cars & Trucks

2 Answers

Windsheild washer motor will not work.


Windshield Washer Pump

1990 Ford Truck F150 1/2 ton P/U 2WD 5.0L FI 8cyl

The Windshield Washer Pump is located: Under hood, driver side front side of wheelwell, mounted inside washer bottle.here's the part. TAAP Windshield Washer Pump 7 664 1990 Ford F150 1 2 ton 2WD 8...

Jan 14, 2014 | 1990 Ford F150

1 Answer

Translating japanese to english on fuse box


is located under the dashboard on the driver's side. The fuse label is attached under the steering column. If something electrical in your vehicle stops working, check for a blown fuse first. Below table outlines detail fuse number, its ampere and circuits protected. honda-crv-interior-fuse-diagram-thumb.png
No.
Amps
Circuits Protected
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
7.5 15 10 7.5 (15) (20) _ 10 7.5 7.5 10 10 10 7.5 7.5 10 10 20 15 7.5 20 _ _ (20) 20 20 (20) 15 15 20 (15) 20 20 7.5 7.5 10 7.5 30
Power Window Relay Fuel Pump ACG ABS/VSA Heated Seats* Front Fog Lights* Not used Rear Wiper ODS (Occupant Detection System) Meter SRS Right Headlight High Beam Left Headlight High Beam Small Light (Interior) Small Light (Exterior) Right Headlight Low Beam Left Headlight Low Beam Main Headlight High Beam Small Lights MAIN TPMS Headlight Low Beam Not used Not used Moonroof* Door Lock Front Left Power Window HAC Option Rear Accessory Socket Accessory Front Right Power Window Accessory Power Socket on the Center Table* Rear Right Power Window Rear Left power window ACC Radio ACC Key lock HAC Daytime Running Lights Front Wiper

Dec 13, 2010 | 1997 Honda CR-V

2 Answers

Honda Accord Saloon 2001 Windscreen Wipers : Intermittent wipe no longer works - Goes on to normal wipe Wipers do not stop when shut down. - Require to turn off ignition to stop them


2 things.

1 bad connections on the motor itself under the skuttle panel below the window screen.

2 the stalk from the steering wheel is broken, they have small metal parts inside they sometimes come lose and stop working, just replace it.

Jan 13, 2010 | 2001 Honda Accord

2 Answers

Ml350 2003, the wipers aren't working, front and


I have ML350 SE and my front wipers stopped working overnight (back wipers are working ok). I changed the fuse but it did not help.

Mar 12, 2009 | 2007 Mercedes-Benz ML350

2 Answers

Rear wiper does not work at all. front wipers work fine. rear washer works


1. check the fuse to the rear wiper motor
2. check for power to rear wiper motor at the motor (power wire going in to the wiper motor with rear wiper switch on)
If you have good fuses & have power going in to the rear wiper motor...
3. Pull old rear wiper motor and install a new rear wiper motor.
Thank you please drive thru......

Feb 26, 2009 | 2001 Ford Expedition

2 Answers

Front wipers stopped working but you can hear the motor run also


If the wipers were buried under snow/ice or frozen to the windshield, you may have blown the red 10 amp fuse located in cavity 9 in the fuse block located on the bottom left side of the instrument panel near the parking brake pedal.
In order of easiest to check:
1) ensure wipers not frozen to windshield.
2) ensure wiper arms are not loose on the pivot stud,
3) check the red 10 amp fuse.
You stated that "you can hear the motor". Which motor do you hear? The engine or the wiper motor?
If you hear the wiper motor, then the fuse is alright. Try 1) and 2) above.
PT Stanley

Jan 20, 2009 | 1998 Dodge Grand Caravan

2 Answers

Find the windsheild wiper fuse on a 96 grand caravan?


Fuse panel is located below left side of instrument panel.
Group 8W-53 Wipers Notes Wipers (Part 1 Of 2) 58867186

Jan 13, 2009 | 1996 Dodge Grand Caravan

Not finding what you are looking for?
1993 Plymouth Voyager Logo

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...