Question about 2000 Chevrolet Venture

2 Answers

I have a new key cut and the security comes on. What can I do?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 5,763 Answers

This key now needs to be programed to the anti theft system, make sure who ever made the key knew what they where doing and gave you the correct key with chip, heres how to program the new key.
step1) insert old key in ignition and turn ignition on but dont start engine, after 3 seconds turn key off and remove.
step 2) Within 10 sec, insert new key and turn ignition on the same as before, security light will light untiul key is learned . when light goes out remove key within 10sec, of light going out, this may happen so fast you never see security light light up , so when light goes out remove the key, leave key off for 15 sec, then try it. hope this helps. note, if you wanted to program more keys you would just keep putting them in within 10sec of removing last key, following directions of step two. when done then turn key off for more than 15 sec, and the relearn is shut off,

Posted on Aug 21, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,927 Answers

If your old key has a chip in it,then the dealer ship will have to code it.If not,try relearning the key to the ignition,turn the key on,leave it on 10 minutes,then turn it off,and right back on,do this three times,a total of thirty minutes,if this was at all helpful,please rate,thank you.

Posted on Aug 21, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How would I start a 2000 2.4 litter Mitsubishi triton glx using a non coded key


Hi Russell, Im AL the owner of Big As Auto Repair.

Russell, you cannot start a security installed vehicle with a none security key. If you have lost your key to the vehicle then here's what you can do. Take the last 8 of your VIN Number and your vehicle to the Mitsubishi Dealer and they can cut and program a new key to the security module. NOTE: Another way to do this is to have the dealer cut a new key for the vehicle and then call around to find a lock smith that has the ability to program the key to the vehicle. NOTE: I would check to see which way is cheaper. To Tow the vehicle OR have a lock smith come to you. Hope this helps and please visit my auto-repair-website here: http://www.bigasautorepair.com/

Dec 12, 2015 | Mitsubishi Cars & Trucks

1 Answer

How to get the key code by vin for 1998 buick lesabre


Hi, Leslie do you mean like how to cut a key or how to eletronic key security properties? Look in the owners manual sometimes their is a blank key that comes with car that haste the cut # on it. The 98 was the last year that electronic key lock security wasn't mandatory. If active can bee shut off by shut off by radio button controls also should be in owners manual. Good luck, feel free to ask anything about the 98 LeSabre I,m restoring one and know more than I ever wanted to

Aug 24, 2014 | 1998 Buick LeSabre

1 Answer

I havw a 1997 firebird security light comes on and car won`t crank. Keyfob does nothing. Could it be the antitheft module?


Been there: had broken wiring in the key cylinder -- wouldn't read the 'chip'. Dealer dinged me for a whole assembly, meaning a new key-cut .. and new IGN keys !
Learned later that I 'could' have bypassed the chip-reader with $1.59 of resistors from RadioShack ..

Jul 23, 2011 | 1997 Pontiac Firebird

2 Answers

2003 Ford Expedition need extra key- I think needs key with chip


any locksmith can make a new key, yes its expensive.

Dec 04, 2010 | 2003 Ford Expedition

1 Answer

1997 CADILLAC DEVILLE ENGINE CRANKS BUT WILL NOT START THE THEFT SYSTEM CODE FLASHES AND READ THE CODE TCS B1750 PASS KEY FAILURE CURRENT THE RESISTANCE OF THE KEY IS 7.5 KOHMS AND THE RESISTOR WAS CUT IN...


On the key there is a diode theat the key connects inside the cylinder lock from the lock cyclinder their is two white wires that thread down the collum to the maim collum connector.here they plug into the main harness. If this white set of wires is broken or cut anywhere or connected to ground then the security system won't let the car start. A new tumber comes with the white wires and the contacts that touch the key. I remove the new contact wire assembly from the old tumbler and install the new on that came with the new tumbler. I don't use the new tumber as I don't have a key with the diode in it thats right for the car. with the old key in the old tumbler with the new wire and contaacts all assembled the car should reconize the key and run like it used to,

Oct 27, 2010 | 1997 Cadillac DeVille

1 Answer

Having a challenge programming a 1999 Lexus RX 300 newly cut key.


did the lock smith cut key with resister in in maybee not gotta go to dealer get one cut then put old key in start car then turn of remove key put new key in turn on till security light goes out then start car

Aug 29, 2009 | 1999 Lexus RX 300

2 Answers

No chip in the key


There is a  security resistor on the key and your going to have to get a new key from GM dealer and  it will come programmed right from the dealer. Once you have the new pass lock keys, your going to have to reprogram the Cars ECM to recognize the new keys and takes about 30 min. You can call a lock smith to come to you and he can cut new pass lock keys and reprogram the car and keys together where you are so you don't have to pay for the tow to the dealer. Good luck and hope this helps. 

Jul 15, 2009 | 1991 Chevrolet Camaro

1 Answer

Security light flashing, does not turn over, do i replace ignition or ecm or both? Do i need new key if i replace ignition? I went to work car started fine. Then went to start the car and go homeand the...


your key has been deactivated, try placing the key in the ignition turn the key to on and leave it there for a minimum of ten minutes. then turn the key off and try restarting the car. this should recode the key to the car and it should start. If this dont work you will have to get the key recoded for your car.

Feb 02, 2009 | 1995 Pontiac Grand Prix

1 Answer

Security light flashing, does not turn over, do i replace ignition or ecm or both? Do i need new key if i replace ignition?


Chances are the wire going to ignition broke allowing the security to start flashing.this will keep the
car from cranking.On my 93 bonneville I went to Radioshack and got a 680 ohm resister,cut the 2 small
yellow wires on lower steering column under dash,soldered resister to the 2 yellow wires coming from harness.Cost of repair..$1. you can read the resistance on the key by using ohm meter on each
side of chip in key

Jul 30, 2008 | 1997 Pontiac Bonneville

Not finding what you are looking for?
2000 Chevrolet Venture Logo

298 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...