Question about 2000 Lincoln Navigator

1 Answer

Changed starter solenoide swicth with an after market one, now my 2000 navigator check engine light is on and truck barely moves

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Have a garage or auto parts store check the code with an analyzer and that will tell you what the problem is

Posted on Aug 21, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

No engine cranck, no warning lights

Check solenoid on starter motor.

A quick fix which works on occasion when solenoid hasn't completely failed is to strike the starter motor body with a hammer whilst trying to start.

Check power to solenoid with the key turned to crank position.

No power to solenoid? Check steering lock cluster, relay and fuses.

Do you have a flashing key on the instrument cluster? Change or re-program the ignition key

If you have no warning lights, no power to solenoid then check negative terminal fixing from battery.

If all is well, yet no crank, then replace starter motor and solenoid.

Oct 29, 2012 | 2005 Dodge Grand Caravan

1 Answer

Unable to remove starter on a lincoln navigator 2000

Where are you stuck?
Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. NOTE: To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. Start the engine several times to check starter motor operation.
Let me know how you make out..

Feb 17, 2011 | Lincoln Navigator Cars & Trucks

1 Answer

Silanoid fo 2000 navagator, location of

are you talking about the stater solenoid if you are it's on the firewall in the engine compartment and some have two one in the starter and one in the firewall.

Jul 08, 2010 | 2000 Lincoln Navigator

1 Answer

My 2000 gmc truck will not start. New starter,

I assume that you mean that the starter will not run. Do you hear the starter solenoid operate (click) when attempting to start? If so, using either a voltmeter or test light, look for 12 volt power at the battery side of the solenoid. If none or it disappears when the starter attempt is made, check the cables from the battery for badly corroded ends. Also, check the grounding cable running from the frame/body over to the engine block for damage. If you hear no click from the solenoid, look for power which should appear at the small terminal of the solenoid when starting. If you get power, replace the solenoid. If no power, then look for a blown fuse, bad relay, bad ignition switch, or any damaged wiring. Make sure the new battery is fully charged. Hope some of this helps!

Dec 14, 2009 | 2000 GMC Sierra

1 Answer

I replaced battery and it still won't start. Elect power is on, but nothing happens as far as starting the engine

Do you hear clicking from the engine when trying the starter? If not sure, have someone try the starter while you listen at the engine. If it comes from the solenoid, it should be near the starter motor and have a large wire going from it to the starter motor and another large wire going to the battery positive post. If no clicks, check for a loose or blown fuse for the starter. Again, if it did click, you need a test light or a voltmeter to determine if the problem is the solenoid or it is the starter motor. You should read 12 volts DC on a meter or get light if using a test light. Check the battery side of the solenoid (light on) and try the starter. If the light stays on, the battery side cable is ok. Move to the starter terminal with the light and try the starter--if you get light, the starter motor is bad and needs replaced. If you get no light, then the solenoid is bad and needs replacement.

Sep 14, 2009 | 1997 Honda Accord

Not finding what you are looking for?
2000 Lincoln Navigator Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts


Level 3 Expert

80339 Answers


Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides