Question about Toyota Matrix

4 Answers

Chiled droped a quarter inside where the gear handle and its just diaprears inside, in metrix 2010. is there any future proble? do i need to get it out before go for linge drive?

Posted by on

Ad

4 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Toyota Master
  • 1,075 Answers

No i dont think ther will be any problems as the carpet is under the the gear change,and the quarter will just land on the carpet.adrian,,,,,,,,,,

Posted on Aug 21, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

Hiya,
Usually no issue....in fact when I pull consoles on most cars off I usually find at least a dollar or two in coins from exactly the same reason, kids "posting" them down the cracks. As long as the gear lever operates OK through all the gears you should be fine.

Regards

Posted on Aug 21, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 117 Answers

The only real possibility of a problem would be that the quarter would work its way into the shift lever tunnel and prevent you from shifting. If this happens while you are in drive"which would be the most difficult situation" you will still be able to turn the vehicle off with the ignition switch. Also i have taken many consoles out of vehicles and have accumulated quiet a collection of change:)
please vote if this helped

Posted on Aug 21, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Consider this spot as a piggy bank. It will be OK to drive

Posted on Aug 21, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace outside door handle?


You need to take the panel off of the inside of the door in question an look inside , there are a couple of rods hooked to it. A couple of nuts hold it fast . Go to you tube an search outside door handle replacement for 2010 ford focus , there's probably a video showing step by step on how to do it . An tools needed

Oct 14, 2015 | 2010 Ford Focus 1.6

1 Answer

2010 Adrenalin. Why is there a heavy compression roar at 80?


Its droping in a lower gear. Shift solenoids may be worn or some othr part. Trans mite need download or upgrade from a scantool. Checfluid and make ajustments...git atestdrive from a mech who knows his stuf

Jul 30, 2015 | Ford Cars & Trucks

2 Answers

Hi I have an Audi A4 Avant 2010 where the driver door wont open from the inside. It is fine from the outside. The handle from the inside now feels like there is no resistance. Thanks


IT LOOKS LIKE THE CABLE FROM THE LATCH IS BROKEN!!CHANGED ONE 3 DAYS AGO..U HAVE TO TAKE OUT THE INNER DOOR PANEL TO ENSURE THAT IT IS BROKEN....IF U NEED MORE INFO LET ME KNOW!!

Mar 07, 2015 | 2010 Audi A4 Avant

1 Answer

How do I adjust the headlights on a 2010 Miata


Inside the engine bay, behind each headlamp is a white plastic funnel looking thing with a gear inside. Use a large phillips head driver to turn the gear inside. Go to your local fire station and back up a ways raise or lower to your liking.

Nov 07, 2014 | 2010 Mazda MX-5 Miata

1 Answer

Dropped my keys inside my mazda 3 -2010 gearbox HELP!


You dropped your keys into the center console which encloses the floor shifter. The console can be disassembled/removed to retrieve your keys but the skills required may preclude a do it yourself approach. An independent non-dealer mechanic probably could do the job at a reasonable cost

Oct 12, 2012 | 2010 Mazda 3 1.6

1 Answer

The left rear door window fell off the track. How do I remove the door panel to access it.


This is the complete procedure you stop when you see the problem.



1. REMOVE REAR DOOR INSIDE HANDLE BEZEL


(a) Remove the screw.


(b) Using a screwdriver with its tip taped, disengage the 2 claws A.


(c) Pull out the the rear door inside handle bezel in the direction indicated by the arrow, disengage the claw B, and remove the rear door inside handle bezel.


2. REMOVE DOOR PULL HANDLE


(a) Using a screwdriver wrapped with the protective tape, disengage the 2 clips and remove the door pull handle.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


(a) Remove the screw.


(b) Disengage the 7 clips.


(c) Disconnect the connector and pull up on the rear door trim board sub-assembly to remove it.


4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


(a) Remove the bolt.


(b) Disengage the 2 claws and separate the rear door inside handle sub-assembly.


(c) Disconnect the 2 cables and remove the rear door inside handle sub-assembly.


5. REMOVE REAR SPEAKER


6. REMOVE REAR DOOR SERVICE HOLE COVER


(a) Disconnect each connector and remove the rear door service hole cover.


HINT:


Remove the remaining tape on the door side.


7. REMOVE REAR DOOR GLASS RUN


(a) Connect the window regulator switch assembly.


(b) Fully lower the door glass.


(c) Remove the rear door glass run.


8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


(a) Remove the 2 bolts, the screw and rear door window division bar sub-assembly.


9. REMOVE REAR DOOR QUARTER WINDOW GLASS


(a) Pull out the direction indicated by the arrow, remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit.


10. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


(a) Remove the rear door glass sub-assembly as shown in the illustration.


(b) Disconnect the window regulator switch assembly.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


(a) Disconnect the connector.


(b) Loosen the temporary bolt.


NOTICE:


If the temporary bolt is removed, the rear door window regulator may fall and become deformed.


(c) Remove the 3 bolts and the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.


(d) Remove the temporary bolt from the regulator.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


(a) Using a "torx" driver (T25), remove the 3 screws and power window regulator motor assembly rear.


14. REMOVE REAR DOOR LOCK ASSEMBLY


(a) Disconnect the connector.


(b) Remove the bolt.


(c) Using a "torx" socket wrench (T30), remove the 3 screws.


(d) Slide the rear door lock assembly downward, pull out the link from the outside handle frame, and remove the rear door lock assembly and cables as a unit.


(e) Remove the door wire harness packing.


(a) Using a "torx" socket wrench (T30), loosen the screw.


(b) Disengage the 2 claws and remove the rear door outside handle cover.


(a) Disengage the 2 claws and remove the rear door outside handle pad rear.

Jan 03, 2011 | 2006 Toyota Highlander

3 Answers

My rear quarter window slides freely up and down


The window regulator is in need of inspection or replacement. the gear on the knob assembly is not contacting the window gear, therefor it will not operate the window from the knob while cranking.

Jul 07, 2010 | 1966 Ford Mustang

1 Answer

The door doesnt open. The inside handle and the outside handle don't work and the car door will not open.


I have a 1996 Jetta Trek edition, and had the same problem both sides, driver and passenger side.
It's the door lock assembly, there is a little linkage that breaks inside, you need to replace the whole lock assembly, buy it at an auto salvage $40 - $60, or buy it at the dealership at cost, replacing it yourself, from
0 to 10, is a 6, not easy to do, buy a chilton book it is helpful.
If your up to the task it can be done.
You got to have some tools, flat screwdriver, torx driver set, metrix allen set.

Good Luck!
RMak

Aug 14, 2009 | 1996 Volkswagen Jetta

1 Answer

Cant find driver door windows 1996 jeep cherokee 2 door in Chile


I checked shipping cost and its around $700.00 !! I could buy a whole car for that much!!! I see why you are having a problem. Good luck with making something!

Mar 17, 2009 | 1996 Jeep Cherokee Sport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...