Question about 1995 Ford Escort

1 Answer

Whats the bolt pattern for my 1995 ford escort head?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Expert
  • 262 Answers

1.8 liter..NOTE: Lubricate the cylinder head bolts using the specified engine oil.

Install the cylinder head bolts. Tighten the cylinder head bolts in 2 or 3 steps in the sequence shown to 76-81 Nm (56-60 lb-ft).

Whats the bolt pattern for - b064be7.gif
1.9 liter
Apply a light coating of engine oil to the threads of the new cylinder head bolts. Install the new cylinder head bolts to the cylinder head. Following the sequence shown below, tighten the cylinder head bolts to 40-60 Nm (30-44 lb-ft). Loosen all cylinder head bolts approximately two turns, then retighten the cylinder head bolts to 60 Nm (44 lb-ft) following the sequence shown. After tightening, turn all bolts 90 degrees, in the same sequence. Complete bolt tightening by turning them an additional 90 degrees, in the same sequence. 398246b.gif

Posted on Aug 21, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Put a head and head gasket it started but blew white smoke and startednsteaming threw. The motor

Incorrect torque values on head, other damage like cracked block, head is cracked, gasket is damaged. Lots or possibilities . Did you replace the head bolts? On most vehicles the head bolts are not reusable.

Jul 30, 2016 | 1995 Ford Escort

1 Answer

Whats the bolt torque specs on a 1988 ford escort gt?

You didn't specify a particular bolt so your best bet is to get a comprehensive workshop manual. I have linked to an assortment:
ford escort repair manual ebooks for download 81595 results

Jan 04, 2015 | 1988 Ford Escort EXP

1 Answer

Pattern to torque heads on 460 mortor and how many lbs

The pattern to torque almost any cylinder head is start at the center two bolts and move outward example: 10 6 2 3 7
9 5 1 4 8

Apr 04, 2010 | 1995 Ford F250

1 Answer

Could you help me with the ford escort 1600 zetec (1995) twin cam cylinder head torque settings please regards tom

Tightening sequence is (imagining the bolts looking down from the front of the car, top left to right being bolts 1,2,3,4,5 and bottom left to right being bolt 6,7,8,9,10 the tightening order is 8,3,9,2,7,4,6,5,10,1 Draw it out on paper to make it become clear. (it will I promise)
The tightening is done in stages, Stage one being to screw all the bolts in finger tight. Stage two is tightening the bolts in sequence to 20-30nm Stage three is tightening the bolts in sequence up to 40-50nm Stage four is tightening the bolts in sequence by 90-120 degrees. ---- Data checked and double checked, thats the official way to do it.

Jan 23, 2010 | 1995 Ford Escort

1 Answer

I have a 1995 ford escort lx 1.9 and need to know where the thermostadt is located and how difficult to change

It's fairly simple to change. Remove the water hose from the thermostat, remove the 2 bolts and lift away (may need a flat head screwdriver to pry away from thermostat housing). Below is the diagram for your thermostat. Best of luck.

Oct 25, 2009 | 1995 Ford Escort

2 Answers

Remove ford escort intake manifold

I know this may sound stupid but maybe you have missed one, look to make sure they are all out

Jul 03, 2009 | 1995 Ford Escort

1 Answer

Is the bell housing bolt pattern on a 1980 Ford escort the same as a cortina gearbox?

Yes, the splines are bigger on the 1.6 and up gearboxes on both the input and output shafts

May 30, 2009 | 1983 Ford Escort Gt

1 Answer

Require ford escort rs 2000 1976 torque settings head bolts

2lt overhead cam with them horrible tappet adjusters,cast iron head but valves dont hit the head if the timing belt breaks ,but it does on the 1600 .called a pinto in america .Remember the assembly line well ,have many a fond memory of working on it and the staff canteen on night shift ,what lovely grub we got.Head bolt torque is about 80lbs because i used to pull them down to check them after the machine had tightened them up

Apr 24, 2009 | 1997 Ford Escort

2 Answers

Head gasketrepair

These are torque to yeild bolts, must be replacedd new bolts will have specs.

Jan 02, 2009 | 1986 Ford Escort 4-Door

Not finding what you are looking for?
1995 Ford Escort Logo

813 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5675 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides