Question about 2006 GMC Sierra 1500 2WD

Open Question

Need torque specs for replacing oil pan on 2002 GMC Sierra 1500 4.8 liter

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

Ad
sledge1863
  • 149 Answers

SOURCE: 1999 Saab 9-5 oil pan torque spec

they should be torqued with a 3/8 torque ratchet to 30 inch pounds.

Posted on Mar 06, 2009

  • 51 Answers

SOURCE: oil pan removal on 2002 gmc sierra

did you pull the rubber plugs between the motor and trans out? there are either nuts or bolts up there

Posted on Mar 15, 2009

slave2aslave
  • 302 Answers

SOURCE: suzuki 1400 need torque spec for oil pan

Try here:
www.onlinefreeebooks.net/automotive-machinery.../suzuki/

Posted on Sep 23, 2009

  • 2002 Answers

SOURCE: what should it be for a gmc sierra 1500 5.3 liter oil presssure

If you are talking about oil pressure that would be in the normal range. Hope this helps.

Posted on Feb 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil pan bolt sequence and torque specs for a 1993 gmc sierra 5.7 liter 2 wheel drive 1500


No more than 25lbs and always start from the centre and work out go diagnal

Apr 01, 2017 | GMC Cars & Trucks

1 Answer

What are the torque specs on the head bolts on a 2005 gmc sierra 1500 series 5.3 liter engine


Consult your shop manual. If you don't have one, you can't be doing this job properly, as there are many torque values needed to do it right. Buy a cheap manual to be sure. My 2 cents.

Mar 28, 2016 | GMC Cars & Trucks

1 Answer

Need torque specs for 96 yukon 5.7 liter


Here's a link to the oil pan removal guide with pan bolt torque specs.

Jan 13, 2013 | 1996 GMC Yukon

1 Answer

What's is the torque specs for a 2002 se Pontic


90 inch pounds or 8 foot pounds. Good luck. Scott

Aug 29, 2011 | 2002 GMC Savana

2 Answers

Where can I find the diagram for a 1992 GMC Sierra distributor cap? I need the firing order


The GMC 1500 Sierra have several engine sizes, hope this helped...

1992 GMC C 1500 P/U 2WD 4.3 liter V-6 VIN "Z"

d9ffbf1.gif



1992 GMC C 1500 P/U 2WD 5.0 liter V-8 VIN "H"

6e77604.gif



1992 GMC C 1500 P/U 2WD 5.7 liter V-8 VIN "K"

18df209.gif


Good luck, and remember rated this. TY for using Fixya.

Mar 31, 2010 | 1992 GMC Sierra

1 Answer

Oil pan removal on 2002 gmc sierra


did you pull the rubber plugs between the motor and trans out? there are either nuts or bolts up there

Mar 15, 2009 | 1996 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...