Question about 1997 Mazda Pickup

1 Answer

Back up lights don't work. How can I find the source of the problem? I have changed to bulbs still won't work...

Posted by on

  • TRXSandRacer Aug 21, 2010

    Is it an automatic or manual transmission?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Bad ground,bad wire or back up light switch on transmission

Posted on Aug 21, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I figure out why fuse 15A keeps blowing? My dashboard lights don't work nor do the back lights. My breaks and signals work but at night when I turn the car on the regular lights in the back...


There is a shorted wire somewhere in that circuit. Check to see if any wires are pinched under a bracket or brace where he was working. I have seen it where it was a light bulb the was bad. Need someone familiar with a volt/ohm meter to help trace problem. Good Luck. You did not state where he had been working.

Apr 17, 2012 | 1996 Honda Accord

1 Answer

One of my brake lights are not working on my 2002 Dodge Durango the other side is working. I tried changing the bulb out nothing and I can't tell by looking at the fuse list which needs to be changed.


if one is working and not the other, it won't be a fuse , what happens with the newer light bulbs , the plug in type with the thin lines of contact metal housed in either glass with the bulb , or plastic with the socket, is that in the socket, heat is the bad guy , look into the bulb socket,, make sure that you can see where the bulb contacts will meet up , if your very gentle,, you can use a small screw driver, ( I use a small pick tool when I do this) Lift the contact metal up a little bit,, over time the plastic melts and softens , so the when you insert a new bulb the contacts don't actually touch,, so lift the contacts up, you can also do this to the contacts on the bulb. in this case a little is better, so use care and just lift these thin lines of metal,, so that a good contact can be made

Sep 15, 2011 | 2002 Dodge Durango

1 Answer

My exterior low beam lights won't come on and I have changed them.


Check for voltage at the plug in the back of lights...
If you have voltage, its the bulb.
If you don't have voltage...then check the fuses.
GM has low beam and high beam fuses.

Hope this helps...

Aug 13, 2011 | 2002 GMC Envoy XL

2 Answers

Is there a dash light for the gages because replace ignition switch and key and still no display.


Yes, normally there is small bulbs at the back that light up the gauges

Jun 22, 2011 | 1989 Mercury Cougar

1 Answer

How do i change the rear brake light in a toyota corolla 2003


  • Pop the trunk.
  • Look at the backside of the tail light area – it’s wide open. Turn the affected light bulb socket to the left. It’ll take some force, but you won’t break it.
  • Once it unlocks, you can pull the light bulb out.
  • Push the new bulb in.
  • Put the socket back into its place by pushing it in, then turning to the right. It’ll lock back into place.
  • Test the brake light to make sure it works.
  • Jun 22, 2010 | 2003 Toyota Corolla

    1 Answer

    When I tried to change a breaklamp on my ford Focus -99 something went wrong. Now the automatic light don´t work at all. The position light at the back dosen´t work. What can have happend.


    take it off again and check the multiplug and then remove the bulb and make sure you have fitted the correct bulb ,count the terminals in teh bottom of the bulb holder and the underside of the bulb

    Sep 16, 2009 | 2000 Ford Focus

    Not finding what you are looking for?
    1997 Mazda Pickup Logo

    Related Topics:

    43 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mazda Experts

    yadayada
    yadayada

    Level 3 Expert

    75066 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7754 Answers

    Are you a Mazda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...