Question about Toyota Pickup

Open Question

Toyota 2wd Pickup front wheel bearing torque - Pickup Toyota Cars & Trucks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
michigan man
  • 3533 Answers

SOURCE: replace bearings

try these websites www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your truck wish you the best of luck Michigan Man.

Posted on Oct 22, 2009

Ad
  • 462 Answers

SOURCE: whats the torque on a wheel bearing

103 lb feet

Posted on Aug 09, 2009

  • 4 Answers

SOURCE: need the torque seeting for front wheel bearings

221 ft lbs

Posted on Apr 09, 2010

  • 819 Answers

SOURCE: need torque setting for front wheel bearings

170 ft lbs.

Posted on Jun 21, 2010

jebild
  • 178 Answers

SOURCE: what is the torque setting for the wheel bearing

there's a manual here: http://myweb.dal.ca/is353832/93fsm/

Posted on Jul 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2014 Ford Fusion 2.5L, 2WD Torque Specs for front wheel hub assembly needed Axle nut/bolt, Hub bolts


the four axle nuts, 98 ft lbs, tighten in criss-cross pattern.
The hub nut/wheel bearing, 148 ft lbs, use new nut, don't let vehicle weight sit on the ground while torqueing, it could damage the wheel bearing.
If I left something out, give me a holler.

Jul 26, 2017 | Ford Cars & Trucks

1 Answer

Wheel bearing replacement


25 days old.??
car has 4 wheels, must be guess end of car?
2wd or 4wd, yup , be different.
why not just log in to mitchells DIY and end the saga... google it)
ill toss coin for you, lands heads, for front.
front wheel bearings.
2wd
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and support the front end.
  3. Remove the caliper from the anchor plate and suspend it out of the way.
  4. Disconnect the ABS sensor.
  5. Remove the rotor.
  6. Remove the bolts attaching the hub to the knuckle.
  7. Installation is the reverse of removal. Torque the hub bolts to 76 ft. lbs. (103 Nm).
4wd:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Place the transfer case in 2WD.
  3. Raise and support the front end.
  4. Remove the caliper from the anchor plate and suspend it out of the way.
  5. Remove the rotor.
  6. Loosen the caulking around the front driveshaft nuts. Remove the nuts and discard them.
  7. Remove the 4 hub retaining bolts. NOTE If the hub is difficult to remove, install 2 long bolt in the bolt holes and strike them to loosen the hub.
  8. Installation is the reverse of removal. Torque the hub bolts to 76 ft. lbs. (103 Nm). Use new driveshaft nuts, torquing them to 181 ft. lbs. (245 Nm). Apply new caulking. The caulk should be free of cracks when applied.

May 01, 2016 | 2003 Isuzu Rodeo

1 Answer

99 Toyota 4 runner 2 wd front wheel removal


Install front wheel bearing hub assembly on a ... - YouTube

? 8:42
https://www.youtube.com/watch?v=LQ-DGdt2J2U
Mar 11, 2014 - Uploaded by Andy Taylor
... Install front wheel bearing hub assembly on a 2003-2014Toyota 4Runner .... Pressing a 2005 and up Toyota Tacoma,4Runner, FJ Cruiser 2WD or 4WD ... How to Remove & Replace a Toyota 4x4 Manual Locking Hub ...
images for 99 Toyota 4 runner 2 wd front wheel removal

Nov 26, 2015 | Toyota Cars & Trucks

1 Answer

Front wheel bearing specs on Toyota t100 1995 4 wheel drive


You tighten the nut until the wheel starts getting hard to turn, then back off the nut 1/4 turn.

Jun 18, 2015 | Toyota T100 Cars & Trucks

1 Answer

Knocking sound from front wheel on my 2WD 1992 toyota pickup. It happens as the truck is in motion. there will be a ticking sound as the wheel rotates. it sounds like a metal ball bearing is falling and...


This needs immediate attention . It can be the wheel bearing assembly, the axle worn out, the hub worn out , hitting the brakes.
Now it depends on your resources of technical work and equipment to do the job. Since this requires the removal of the hub assmebly and replacement your technical capacity is important.

Jack up the vehicle and manuall rotate to confirm remove tyre , now checck to confirm and replace accordingly. Use the correct torque, change faulty bushes in the suspension as you remove these front suspension.

Sep 20, 2010 | 1992 Toyota Pickup

1 Answer

What is needed to remedy right hand front wheel bearing play on a 1990 d21 4X4 ute


replace the bearing or wheel hub assembly.

REMOVAL & INSTALLATION 2wd Models NOTE: Refer to wheel bearing service and bearing preload adjustment procedures found in Section 1.
  1. Raise the front of the truck and support it with safety stands. Remove the wheels.
  2. Remove the brake caliper and suspend it with wire, out of the way. Remove the caliper torque plate if equipped.
  3. Remove the dust cap and then remove the cotter pin, lock washer (if equipped) nut lock and nut.
  4. Pull the hub/disc assembly off the spindle with the outer bearing. Don't let the bearing fall out.
  5. Pry the inner oil seal out and remove the inner bearing. To install:
  6. Clean and inspect the bearings and outer races.
  7. Using a brass drift and a hammer, drive out the bearing outer race. Press a new one into position.
  8. Pack the bearings with grease until it oozes out the other side. Coat the inside of the hub and cap with grease.
  9. Position the inner bearing into the hub, coat the oil seal with grease and press it into the hub.
  10. Press the hub assembly onto the spindle and install the outer bearing and thrust washer.
  11. Install the hub nut. Turn the hub a few times to seat the bearings and then loosen the nut until there is 0mm axial play. Using a spring tension gauge, check that the preload (with new grease seal installed) is 2.2–6.4 lbs. (9.8–28.4N)
  12. Install the lock-nut, new cotter pin and hub grease cap.
  13. Install the brake torque plate. Install the brake caliper.
  14. Install the wheels and lower the truck.
4wd Models The hub and bearing service procedures for a 4wd models are basically the same as those for a 2wd version, with the exception of removing the free running hub assembly and the bearing preload adjustment. Refer to Sections 1 and 7 for additional information. Adjust the preload after the wheel bearing is replaced or the front axle assembly is reassembled. BEARING PRELOAD ADJUSTMENT
  1. Thoroughly clean all parts and pack the wheel bearings.
  2. Apply grease to threaded portions of the spindle, grease seal lip and wheel hub.
  3. Tighten the wheel bearing lock-nut with a socket and torque wrench to 58–72 ft. lbs. (78–98 Nm).
  4. Rotate the hub in both directions a few times to seat the bearings. Loosen wheel bearing lock-nut.
  5. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm).
  6. Turn wheel hub several times in both directions.
  7. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm). Fig. 1: Exploded view of the front axle assembly — 2wd models 86718030.gif
    Fig. 2: Removing the bearing outer races 86718032.gif
    Fig. 3: Packing the wheel bearing with grease 86718033.gif
    Fig. 4: Pack the lip cavity of grease seal with grease 86718034.gif
    Fig. 5: Exploded view of the front axle assembly — 4wd models 86718031.gif

  8. Measure wheel bearing axial end-play. The wheel bearing end-play specification is 0.
  9. Install lock washer by tightening the lock-nut within 15–30 degrees.
  10. Turn wheel hub several times in both directions. Wheel bearing should be seated correctly.
  11. If necessary, measure wheel bearing preload. NOTE: Measure wheel bearing preload with a spring-type gauge; measure at wheel hub bolt, with tire removed. The hub assembly should rotate with 1.6–4.7 lbs. (0.73–2.13 kg) of pressure.
prev.gif next.gif

Jul 28, 2010 | 1991 Nissan Pickup

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

1 Answer

Need wheel bearing torque


Spin the rotor and tighten the castle nut untill tight. go tighter untill your carter pin hole lines up with the castle nut.

May 19, 2009 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...