Question about Mazda B2600

Open Question

Good day i'm working on a mazda b2500 pick-up dual cab awd diesel, and replaceing bearings for rear half shaft and found the bearing tight goin on at the bottom just near threads, is it suppose to be pressed on?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

leethedeuce
  • 4472 Answers

SOURCE: clutch kit for mazda b 2500 drifter 4x4 diesel d/cab

http://jdmultimate.com/Store/Product/ItmItem.aspx?ItemId=176995&Make=MAZDA&Model=B2500
There you go if you need anything else let me know. I hope you find this appropriate for a FixYa rating.
Thanks,
Lee

Posted on Jun 19, 2008

leethedeuce
  • 4472 Answers

SOURCE: clutch kit mazda drifter 2.5 diesel turbo d/cab 4 x 4 model 2002

http://www.clutchcityonline.com/mazda_b2500.htm
There you go, just click on your year and the clutch kit. You can always call your local auto store and ask them to price it for you.
Thanks,
Lee

Posted on Jun 20, 2008

  • 8 Answers

SOURCE: diagram Mazda 1998 B2500 4cyl 5sp throw out bearing assembly & dustcap

Are you asking where the throw out bearing is located?
If so, removal of your transmission is necessary to access it. It will be on your input shaft of your tranny behind your clutch. Its on the other side of your clutch fork.

Posted on Nov 07, 2008

tommyboinow
  • 324 Answers

SOURCE: Mitsubishi diesel engine

i would not worry about torque settings just tighten them down to what feels comfortable to you, this should be OK. it is how i do it, as long as there is not alot of play in them, you should be fine.

Posted on Nov 26, 2008

  • 3 Answers

SOURCE: high pitched humming noise from rear near side

did they check the other wheel bearings? some time a wheel bearing noise will travel and sound some place different.

Posted on Jan 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Mazda 323/Protege front wheel bearing


The moment you can hear a loud noise coming from front wheels while driving straight that means that your wheel bearings are ready for replacement. In a Mazda 323 BJ (1999-2004) it usually comes every 150-200 thousand kilometers (95-120k miles). To replace the bearing (do two of them in one go even if only one can be heard) you need to do as follows:
Loosen the nut on the half shaft, jack up the car, remove the wheel, dismantle brake caliper and brake disc, remove all ball joints attached to the hub, detach the shock absorber from the hub (no need of removing it completely), once you have the hub basically hanging on the half shaft, untie the nut and pull the hub out of the shaft so you can hold it in your hands. You will need to go to a garage with a 12ton (minimum) press, no point of trying to hammer the bearing out as you may damage the hub and your whole work will be for nothing. Get the old bearing pressed out and the new one pressed in.The Mazda part numbers for the front bearing kit are: B455-33-047A(B,D),GJ21-33-042B,G304-33-065,B21M-33-048.
After getting the bearing fitted into the hub, all we need is to reverse the whole process, put the shaft into the hub, attached the hub to the shock absorber (makes it easier to attach the rest), put the nut and tight it just as much to feel there is nearly no movement (do not overtight it as this might damage the bearing), attach all ball joints back to the hub. Make sure all nuts are tight, use a
tension wrench when needed, put the brake disc back on the hub, install the brake caliper, once you have all them on and tight put on the wheel, then get someone to press the brake while you tight the shaft nut with the tension wrench, check the wheel for play or hard movement. Lower the car down and take a slow drive around (do not accelerate sharply or brake rapidly, just a gentle drive around. Normally a wheel bearing should be in correct position and use after about 200km (120 miles) distance. After that check if it is not overheating (too tight) or there is a play (too loose). Tight or untight if necessary, recheck after same 200km (120 miles).

on Apr 24, 2010 | Mazda 323 Cars & Trucks

1 Answer

Wh does 1st gear jump out on accelerator release ?


There are a few things to check. Engine and transmission mounts replace any broken or perished . 1st gear selector shaft has a indent ball and spring to locate the shaft when in gear, check the spring is not broken. The gear box bearings may be worn giving the drive shaft to much end play. also check gear shift linkage is not worn.

Aug 23, 2014 | 1999 Mazda B2500

1 Answer

2006 escape AWD, replace front hub bearing


Rather than just the bearing, I suggest a new half shaft as the bearings and ABS tone wheel are already assembled. These Escapes are notorious for cracking the tone wheel setting off a code and then disabling the AWD system. So for a very few dollars more than it would take to disassemble the shaft , install bearings and tone wheel just get a new one.

Jun 09, 2014 | 2006 Ford Escape

1 Answer

Changing wheel bearing 1992 dodge caravan


WHAT WHEEL BEARING BEING REPLACED.REAR AXLE BEARING. FRONT BEARING RWD OR AWD WITH HALF SHAFT HUB BEARING.REASON I ASKED YOU BECAUSE ALL THREE HAS DIFFERENT PROCEDURE FOR REMOVING WHEEL BEARING.

Nov 03, 2010 | Dodge Grand Caravan Cars & Trucks

2 Answers

AWD Disable and abs light always come on , already replaced rear selanoid . Whats going?


CHECK ABS FUSE AND RELAY.THE AWD CONTROLED BY SPEED SENSORS ONE IN THE FRONT OUT PUT SHAFT SECOND SPEED SENSOR IN THE REAR OUT PUT SHAFT THIRD SPEED SENSOR IS VECHICLE SPEED SENSOR.BEST TO HAVE VECHICLE FIX AT A GARAGE OR DEALERSHIP YOU WILL NEED DIAGNOSTIC EQUIPMENT TO WORK ON IT.

Aug 30, 2010 | 2002 Buick Rendezvous

1 Answer

Viberation in drive line truck has 7 u joints, replaced the 2 rear ones,vibe still there,but somewhat better. the rest of the seem to be ok is there a different shaft that would fit? at $50.00 a joint it...


Did you change the carrier bearing. It will be cheap compared to a transmission and new drive shaft. Got 1 in my shop right now. Customer did not listen. Check that carrier bearing Cost $1350vs $50

On vehicles covered by this information that are equipped with a two-piece rear driveshaft assembly, the center support bearing may be removed for replacement. To be sure if your driveshaft may be serviced, check with your local parts supplier or dealer for parts availability information.
  1. Matchmark and remove the rear driveshaft assembly. For details, please refer to the procedure located earlier in this section.
  2. Remove the strap retaining the rubber cushion from the bearing support.
  3. Pull the support bracket from the rubber cushion and the cushion from the bearing.
  4. Press the bearing assembly from the halfshaft.

To install:
  1. Assemble the center support bearing to the driveshaft:
    1. If removed, install the inner deflector onto the front shaft half and ***** punch the deflector at 2 opposite points to make sure it is tight on the shaft.
    2. Fill the space between the inner dust shield and bearing with lithium soap grease.
    3. Start the bearing and slinger assembly straight onto the shaft journal. Support the shaft and using a length of pipe over the splined end of the shaft, press the bearing and inner slinger against the shoulder of the front shaft half.
    4. Install the bearing retainer, the rubber cushion onto bearing, the bracket onto the cushion and the retaining strap.

  2. Align and install the driveshaft assembly to the vehicle.

Oct 21, 2009 | 1997 Chevrolet S-10 Pickup

1 Answer

Diagram Mazda 1998 B2500 4cyl 5sp throw out bearing assembly & dustcap


Are you asking where the throw out bearing is located?
If so, removal of your transmission is necessary to access it. It will be on your input shaft of your tranny behind your clutch. Its on the other side of your clutch fork.

Nov 07, 2008 | 1998 Mazda Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...