Question about 1992 Ford Bronco

1 Answer

Ball joints repair how to - 1992 Ford Bronco

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 76 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I just change the upper ball joint on 2001 Mazda b2300


Old, Some times the hole control arm assembly is changed, if you can find it priced reasonably other wise yes, with proper tools the ball joint can be changed. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How to Replace Ball Joints on Ford Ranger
Replacing Ford ranger ball joints
2003 Ford Ranger Ball joint and Control Arm Repair Part 1 Lower Ball Joint
Mazda B2300 Ball Joints eBay


May 19, 2016 | Mazda Cars & Trucks

1 Answer

Torque specifications for upper ball joint and axle nut please?


Hi Robert,here's a link on your upper ball joint repair guide,also join their site,become a member,it's free,then you can use all their repair guides like me. Repair Guides Front Suspension Upper Ball Joints AutoZone com

Oct 31, 2015 | 2002 Ford Explorer

1 Answer

Ball joint repair and how do you do it


To perform the following procedure, the lower control arm must be removed from the vehicle. Refer to Removal And Installation for that procedure.

  1. Using a screw driver or other suitable tool, pry the seal boot off of the ball joint assembly
  2. Position receiving cup, Special Tool 6758 to support lower control arm when removing ball joint assembly. Install Remover, Special Tool 6919 on the top of the ball joint assembly.
  3. Using the arbor press, press the ball joint assembly completely out of the lower control arm.

NOTE: When installing ball joint in lower control arm, position the ball joint in control arm so notch in ball joint stud is in the direction shown. This will ease assembly of the ball joint to the steering when installing pinch bolt.

  1. By hand, position ball joint into ball joint bore of lower control arm. Be sure ball joint is not cocked in the bore of the control arm, this will cause the ball joint to bind when being pressed into control arm.

 

  1. Position control arm with installed ball joint, in an arbor press with Receiving Cup, Special Tool 6758 supporting the lower control arm. Then center Installer, Special Tool 6908-4 on the bottom of the ball joint
  2. Carefully align all pieces. Then press the ball joint into the lower control arm until it is completely seated against surface of lower control arm. The ball joint is correctly installed when there is no gap between the ball joint and the lower control arm. Do not apply excessive force against the ball joint or the lower control arm.
  3. Install a NEW seal boot by hand as far as possible on the ball joint. Installation of the seal boot is to be with the shield positioned as shown.

CAUTION: Do not use an arbor press to install the sealing boot on the ball joint. Damage to the sealing boot will occur if excessive pressure is applied to the sealing boot when it is being installed.

  1. Place Installer, Special Tool 6758 over seal boot and squarely align it with bottom edge of seal boot. Apply hand pressure to Special Tool 6758 until seal boot is pressed squarely against top surface of lower control arm.

CAUTION: A replacement ball joint is not pre-lubricated. Properly lubricate the replacement ball joint using Mopar Multi-Mile grease or an equivalent. Lubricate ball joint after seal boot is installed but prior to top of seal boot being pushed down below notch in ball joint stud. Air must vent out of the seal boot at notch when grease is pumped into ball joint, failure to do so will balloon and damage seal boot. Do not over grease the ball joint, this will prevent the seal boot from pushing down on the stud of the ball joint.

CAUTION: After the ball joint is properly greased, clip the end of the grease fleeing off below the hex. The ball joint seal boot is non-purgeable and further greasing is not required and can result in damage to the seal boot.

  1. Reinstall lower control arm on vehicle.

Mar 07, 2011 | 2000 Dodge Caravan

1 Answer

How to replace upper ball joint on a 1996 honda accord


go to this site for more info-- www.ehow.com/how_5668350_change-ball-joint-honda-accord.html hope this helps you. the upper ball joint you have to change upper arm to repair. you can only change lower ball joint on accords. go to site for more info.

Jan 29, 2011 | 1996 Honda Accord

1 Answer

Removing Ball joints


You'll need the repair manual for this. There are upper and
lower ball joints front and rear. You also have to deal with
a number of suspension components to access the ball
joints. Lower ball joints can be replaced by pressing old
out and new in using a large socket to match circumference
of the ball joint.

Dec 05, 2010 | 1997 Dodge Stratus

1 Answer

Can you show me detail pictures of step by step repair of ball joint and controll arm of 1990 ford thunderbird v6 3.1 automatc


prev.gif next.gif REMOVAL AND INSTALLATION Upper ball joints are not replaceable. The upper ball joint is part of the upper control arm bushing joint and is not serviced separately. If the upper ball joints are found to be defective, the entire upper control arm bushing joint assembly must be replaced. Lower Ball Joint INSPECTION
  1. Support the vehicle in normal driving position with ball joints loaded.
  2. Wipe the grease fitting and checking surface, so they are free of dirt and grease. The checking surface is the round boss into which the grease fitting is threaded.
  3. The checking surface should project outside the cover. If the checking surface is inside the cover, replace the lower arm assembly. prev.gif next.gif

Aug 26, 2010 | 1990 Ford Thunderbird

1 Answer

How to replace upper/lower ball joints on a 94 chevy suburban


YOU NEED SOME TOOLS LIKE 1/8 1/2 DRILL BITS.YOU NEED A PUNCH.YOU NEED A BALL JOINT SEPERATOR.YOU NEED BALL JOINT PRESS TOOL TO PRESS OUT BALL JOINT AND PRESS IN NEW BALL JOINT.YOU WILL NEED A HAYNES REPAIR MANUAL TO SHOW YOU PHOTOS AND GIVE YOU YOUR TORQUE SPECS.

Jul 21, 2010 | 1994 Chevrolet Suburban

2 Answers

Repair lower ball joints


The front lower ball joints are pressed into the steering knuckle. Once the brake components are removed, the CV shaft nut and tie rod ends can be removed. Remove the front strut bolts, and the lower ball joint nut. Separate the lower arm from the ball joint. Once the knuckle assembly is off the car remove the lower joint snap ring and dust boot. Utilizing a ball joint press (should be able to rent from local parts store) press the joint out of the knuckle. Re-installation is naturally reverse of removal. I hope this helps.

Sep 24, 2008 | 1999 Ford Taurus

Not finding what you are looking for?
1992 Ford Bronco Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...