Question about 2005 Mazda Tribute

2 Answers

Tips on replacing front brake pads - 2005 Mazda Tribute

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi hav a rover 75 lost break fluid how do you get air out of abs.

Posted on Jul 13, 2012

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

A good tips to replace your brake pads, clean the working area, clean the tyre and brake caliper with water to take out harmfull elements, safe you jack and stand jack. safe you vehicle on stationary position. and you can open the tyre. make sure you have original parts to maintenance good brake condition.

Posted on Oct 01, 2010

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Front Brake Pad replacement

Nothing new. Same procedure.

Posted on Jun 08, 2008

  • 1 Answer

SOURCE: how do I change front brake pads

You will first need to have a car jack, proceed to jack up the front side of the car you want to work on. Make sure you place the jack on the proper location, refer to instruction in manual. Take off your tire, now the whole brake assembly is visible, there will be two bolts on back of the brake unit. One at the top and one at the bottom. Unscrew both of these and proceed to slide the used pads and the unit you've just unscrewed. Make sure you clean off all dirt, rust and break pad rosedew. Now you'll need a C-clamp, The piece with the rubber protector on it needs to be compressed back into its compartment with the use of your C-clamp. Now that the unit is clean and the compressor is back in the chamber it's time to replace the small steel break sliders with the new ones provided with your new break set, slide your new breaks into those slots, beside the router. Your almost finished, just slide the break compressor back over the breaks and bolt the unit back on, make sure you tighten the bolts well , as these are your breaks and they will save your life. The only thing to do now is clean your tire inside and out while its off and put it back on your car. Have fun and don't worry it's easy.

Posted on Jan 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While trying to change my pads i noticed my rotors seem loose, also i cant get the brakes to stop grinding, squealing after reassembly.


Shane, rotors may seem loose until wheel is on car and torqued to specification, I recommend you take car in for your brakes to be inspected, estimate and repaired at a good shop. Arrange your appointment time so you can be there and watch how it is done and learn from it. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How to Replace the Brakes on 1997 Toyota Camry
How to Replace Front Brakes Toyota Camry
How to Install Replace Front Disc Brake Pads Rotors Toyota Camry 92 96...
Replace Camry Rear Brake Shoes



Jun 12, 2016 | 1997 Toyota Camry

1 Answer

How do i change pads


Jack, If you are talking about brake pads, check the links below for good info, or Re POST year, make, model, and complete question so we can here at fixya can answer your question effectively.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How to Replace Your Car Brake Pads
How to Change Front and rear Brake Pads and Rotors Complete Guide
Replacing Brakes How to Remove Brake Pads Rotors


May 12, 2016 | Cars & Trucks

2 Answers

What size allen needed to remove break pads


Allen wrenches usually come in a set, try 3/8.

Apr 30, 2016 | 2008 Chevrolet Chevrolet Impala LS

1 Answer

I have 98 durango one caliper bolt on front passenger side came out I put new one in and now the brake seems to be locking up


William, did you use the correct bolt(length), did you check all brackets, sliders, seized caliper, pads for damage, free movement, etc.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How To Install Replace Brake Pads and Rotors Dodge Durango Dakota 97 03...

How To Replace the Front Brakes on 98 03 Durango

How To Replace Front Pads And Rotors Dodge Dakota

Mar 21, 2016 | Cars & Trucks

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

2 Answers

How do you change the brakes on a 2004 chrysler town and country and where can you get the brakes for cheap?


Tools you may need: New Brake Pads, Jack and Jack Stands, Lug Wrench, Large Phillips Head Screwdri
Click on the link above for a few tips on how to start this job. Cheep parts can be found at any auto part store just ask for the lowest cost replacement pads and shoes they have. The front pads wear about 2x times faster than the rear shoes. So other than looking at them (rear shoes) I would just advise you to go for the front pads.

Aug 22, 2010 | 2004 Chrysler Town & Country

1 Answer

Want to replace my own front brakes on 2003 outlander. cannot find detailed repair instructions anywhere. any ideas? thanks!


Hello, to replace the front pads first open the hood and remove the brake fluid cover (will make retracting the piston easier). Next losen the lug nuts till you can turn them by hand than jack up the vehicle and use a jack support stand. Once the vehicle is supported remove the lug nuts and wheel, remove the lower caliper screw and rotate the caliper upward. Remove the old pads, use one of the old pads and place it so it centers the caliper, using a large C-clamp position it with the solid end on the back side of the caliper and rotating handle contact the pad in the center or close as possible. Slowly rotate until the piston is fully retracted into the caliper, your brake fluid may run over but its ok. Install the new pads return the caliper to the normal position over the pads reinstall the lower caliper screw. Put the wheel back on tighten the lug nuts till the wheel is evely and firmly in its normal position. Remove the jack stand lower the vehicle, put the brake fluid cover back on and pump the brakes until they are firm and check the fluid, add some if needed. Tighten the lug nuts, check for leakes. After starting the vehicle pump the brakes a few times, now the fun part the test drive :) allow you self more than normal distance to stop. Tips, I always set the parking brake when working on the front brakes, some people use a 2x4 instead of a brake pad to retract the piston into the caliper, double check your work, i always do and take your time.

Nov 25, 2009 | 2003 Mitsubishi Outlander

2 Answers

Creaky sound upon tapping brake, and brown right rear tire


Looks like you need to change the brake pads sooner than later, the brown residue is the brake dust and the burning smell might be the dust hitting the the tyre.

Jun 15, 2009 | 1994 Nissan Pathfinder

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

1 Answer

How to change rear brake pads on 1991 saab 900 Hatchback


I need to change front and rear brake pads on my Saab 9-7x. Any hot tips or suggestions

Jul 20, 2008 | 2006 Saab 9-7X

Not finding what you are looking for?
2005 Mazda Tribute Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...