Question about 2000 Dodge Caravan

1 Answer

Instructions on how to change the output speed sensor

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 56 Answers

Disconnect the negative terminal of the battery raise vihicle on hoist,, disconnect autput sensor connector,,,and unscrew and remove the sensor,,,look out 4 the oring,, the VSS is mounted to an addapter naer the transmission output shaft,,,,,,,,,tighten 20ft,,,lbs

Posted on Aug 20, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0720 stratus codes


code p0720 refers to output shaft speed sensor(OSS)--circuit malfunction====causes--wiring--OSS sensor--ECM/TCM
of it has just happened check the wiring and connections to the transmission for water and corrosion or replace the OSS sensor in the transmission.

May 08, 2013 | 2002 Jeep Liberty

1 Answer

Po731 and po700 the car don't change speed


replace the output speed sensor on you 4 speed trans, 3.3 engines only have 4 speed transmissions. The output sensor is located next to the transfer gear. Or if you are looking the two sensors, it would be the one on the right.

P700 = PCM has a transmission code in the EATX controller, and P0731= Gear ratio error in 1st. Replace the output speed sensor and clear the codes.

May 26, 2011 | 1999 Dodge Intrepid

1 Answer

91 cherokee shifts fine at fist but after a minute or so it wont shift out of first gear. changed the output speed sensor but no change


Sounds like a bad out speed sensor.Are you sure you replaced the correct sensor?This trans(AW340)Has an output speed sensor and a vehicle speed sensor.The output speed sensor is located on the side of tail housing just next to where it bolts to transmission case.The vehicle speed sensor will be about midway of the tail housing or on the transfer case tail housing on the 4x4 models.It may be a good idea to have a tranny shop you trust run a diagnostic and see if you are getting output sensor signal to TCM( transmission control module behind glove box)and take a look at TPS (throttle position sensor)signal when it is hot to make sure you replace the correct part.I have seen bad TPS sensors on these jeep not affect engine drivability because the sensor is really two(one for trans and one for engine)thus the two plugs on the TPS sensor for the automatic Cherokee.Good Luck and let me know if I can help.

Mar 21, 2011 | 1991 Jeep Cherokee Limited

1 Answer

I need to find out where the output speed sensor goes or 96 dodge grand caravan


if your standing in front of the car looking down at the transmission, the output speed sensor will be on the right (drivers) side of the front of the transmission. The sensor in the middle of the trans cooler lines is the input speed sensor. The output speed sensor looks identical to that one. It is easier to access/change it from under the car. You will need a 1' socket to remove and install the new one.

Mar 20, 2011 | Dodge Grand Caravan Cars & Trucks

2 Answers

Po720 code and po733 code plus leaking oil


P0720-OUTPUT SPEED SENSOR ERROR

WHEN MONITORED
The transmission gear ratio is monitored continuously while the transmission is in gear.

SET CONDITION
If there is an excessive change in output RPM in any gear. This DTC can take up to five minutes of problem identification before illuminating the M.I.L.

POSSIBLE CAUSES[*]Output speed sensor signal circuit open[*]Speed sensor ground circuit open[*]Output speed sensor signal circuit short to ground[*]Speed sensor ground circuit short to ground[*]Output speed sensor signal circuit short to voltage[*]Speed sensor ground circuit short to voltage[*]Output speed sensor[*Powertrain Control Module (PCM)[*]Intermittent wiring and connectorsi cen get you a full flow chart on how to check it out if you wish

p0733 Gear 3 Incorrect ratio

Jan 03, 2011 | Chrysler Voyager Cars & Trucks

1 Answer

Replacing output speed sensor on 2002 sonata


try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 19, 2009 | Hyundai Motor 2002 Sonata

2 Answers

VEHICLE SPEED SENSOR


The VSS sensor is located on the transaxle .
If the VSS is defective replace the instrument cluster

Nov 15, 2008 | Hyundai Motor 2002 Elantra

Not finding what you are looking for?
2000 Dodge Caravan Logo

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...