Question about 2002 Jaguar X-Type

2 Answers

P1000 problem loss of power after 10 minutes

P1000 problem loss of power after 10 minutes travel no response from the accelerator.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 560 Answers

P1000 is not really a fault code, if there are no there are no other codes stored then perform the following:

Disconnect the positive terminal on the battery, hold the terminal to the chassis for 2 - 3 seconds, this defuses the ecu and drains stored data thus clearing P1000.

Now wait 10 minutes.

Then reconnect battery.

Start car *without touching gas pedal*

Leave car idling for a good 5 - 10 minutes then jump in and go on a minimum 12 mile drive, you will need to perform a few normal driving conditions, fast, slow, stop, pull away etc so just a normal day to day trip to the town would suffice.

Hopefully this will sort it, if not report back

Regards

Lloyd


Posted on Aug 20, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Jaguar Expert
  • 279 Answers

Yep agree with above you may wish to check out http://www.bluejag.co.uk regarding drive cycles after an ECU reset

Posted on Dec 19, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Loss in engine power, sluggish responses, low top speed, etc.


If your car has
  1. Poor fuel responses
  2. Lost its "power"
  3. Low RPM
  4. Lower top speed
  5. Burns a lot of fuel
Then it could be because of carbon build-ups in your engine's combustion chamber. This is left behind with unburned fuel. It causes poor acceleration, a loss in power, lower top speed, and burns more fuel than it really has too. Not to mention causes smoke belching.

The best way to get rid of that would be to have a carbon ridding solution injected into the combustion chamber. The solution will liquify the carbon and other build-ups, which would then restore the "power" of your car. You'll get better acceleration, higher rpm and top speed, save fuel, etc. have a mechanic do it for you. It's alot cheaper and faster than having the engine overhauled (overhaul could trigger "loose compression").

on Aug 08, 2008 | 1995 Toyota Camry

3 Answers

The car will run fine for about 10 minutes then it will stop accelerating???


ENGINE HESITATES WHILE ACCELERATION

LOSS OF ACCELERATION


It can be fuel pressure issue or it's the problem with accelerator pedal or its clogged filters causing there.

There are many other possibilities. I suggest you to go through the list of help links mentioned below, these will help you to confirm where the actual fault lies: -------

Jerks and Hesitates During Acceleration?

http://technoanswers.blogspot.in/2012/07/2004-dodge-town-country-jerks-and.html

-----------

Loss of acceleration?

http://technoanswers.blogspot.in/2012/02/loss-of-acceleration.html

---------

Headlights flickering and car hesitates to start?

http://howtobyme.blogspot.in/2012/02/headlights-flickering-and-car-hesitates.html

--------

How exactly the Vehicles Accelerator Cable works?

http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-accelerator-cable.html

-------------

How exactly Vehicles Accelerator Pump Diaphragm Works?

http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-accelerator-pump.html

--------

2000 Toyota Avalon: Engine Lean Codes and Knock Sound on Acceleration?

http://whatisbyme.blogspot.in/2012/05/2000-toyota-avalon-engine-lean-codes.html

---------

2004 Toyota Avensis: Acceleration And Deceleration makes noise on Front End?

http://whatisbyme.blogspot.in/2012/05/2004-toyota-avensis-acceleration-and.html

---------

Wheel hop under hard acceleration?

http://technoanswers.blogspot.in/2012/04/wheel-hop-under-hard-acceleration.html

--------

2009 Chevy impala accelerator pedal sensor?

http://technoanswers.blogspot.in/2012/02/2009-chevy-impala-accelerator-pedal.html

---------

Nissan Pathfinder stalls and bucks on Acceleration?

http://technoanswers.blogspot.in/2012/02/nissan-pathfinder-stalls-and-bucks-on.html

--------

Acceleration lag problem?

http://repairhelpcenter.blogspot.com/2012/01/acceleration-lag-problem.html

-------------

These details will help.

Thanks.

Nov 28, 2012 | 1999 Mercury Cougar

1 Answer

My 2001 C180 has recently on four separate occasions while in transit suddenly revved to the red levels without warning. On one occasion I was travelling at 90 km/hr when it suddenly revved to the red...


Hello! The Pedal Value Sensor (PVS), a device that sends gas pedal positioning to the Electronic Control Module (ECM) is the most likely intermittent component...It is located under the hood...Drivers side...Next to the brake booster...The Throttle cable connects to it...It has a 5 wire plug with the following wire colors...Brown/White...Violet/Yellow...Violet/Green...Brown/Yellow...And Blue/Brown...
Check the connector for loose, frayed, or broken wires...Radio Shack sells a product called DeOxit...Cost $15...It is a "no touch" electronic contact cleaner...Two spray cans...Pull connector and spray Cleaner into both female/male ends...Wait 10 seconds and re-connect...If the problem continues replace the sensor...

Guru....Saailer

Jan 27, 2011 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

Hyunday Santa Fe 2008 3.3l Sudden loss of power while driving on the highway. Engine does not cut out but idles apparently normally. No response from engine when stepping on accelerator pedal. ESC and...


well, if check engine ligth on have the codes pull to find out the problem it may be mapp ,air ,sensor bad ..if engine ligth is on its picking up a a code..

Dec 20, 2010 | Hyundai Santa Fe Cars & Trucks

1 Answer

Hi, The 2 codes showing up are p1000 & p1645.engine light on I had the battery die on me 10days back...the car had completely stalled


P1000 is a keep alive memory code, nothing to worry about. p1645 is probably loss or low power codes from the battery going dead. I would just erase these codes and go from there.
Randy

Nov 09, 2010 | 2002 Jaguar X-Type

1 Answer

Obd2 system rediness status won't clear so I can run the smog test due to replacing the battery.


takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

Sep 15, 2010 | 1998 Mitsubishi Eclipse

2 Answers

1992 jeep wrangler (4.0l , standard)- power loss after warm up.


disconnect exhaust ,muffler or cat may be stopped up

Jan 31, 2009 | 1999 Jeep Wrangler

2 Answers

Power loss in 2004 Corolla Verso D-4D T2 at speed


You might want to check the MAF sensor(Mass Air Flow) and clean it with MAF/MAP cleaner. I am also kind of puzzled with this problem as I have a 2004 Corolla also, I only had power loss when my MAF went bad.

Jun 03, 2008 | 2004 Toyota Corolla

Not finding what you are looking for?
2002 Jaguar X-Type Logo

527 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...