Question about 2005 Ford F-150

1 Answer

My 2005 f150 is skipping and i put plugs in and coils it still reads a code on bank number 3 and skips

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Next step is to check if the fuel injector is operating correctly. Also make sure that the spark plug is firing, dont assume it is firing because you replaced the plug and coil, verify that its working.

Posted on Sep 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 monte carlo 3.4 130,000 skips on start up


I'd suspect a sticking injector--car should have set the check engine light. Read the code(s) to progress further. If the coil pack were a problem, it would not be likely to fix itself. If the codes indicate an injector problem, try an injector cleaner in the fuel--worst case, replace the bad injector. The codes should indicate which cylinder to change the injector.

Sep 09, 2012 | 2003 Chevrolet Monte Carlo

1 Answer

Changed sensor 1 bank 1 and found I have four on 96 Yukon makes noise like putting underneath. Now want start. Wuts wrong


tell me did, did skipping start after you replace oxygen sensor or did vechicle already have skip before sensor change if so skipping can be caused by intake leak,bad spark plugs and wires,could have restricted fuel filter, weak fuel pump or weak ignition coil. if skipping occur after you replaced oxygen sensor could have loose sensor or cross thread sensor threads causing exhaust leak around oxygen sensor.

Aug 26, 2012 | Cars & Trucks

2 Answers

Engine seemed to skip at about 70 mph and service engine light came on. Then seemed to skip several more times at different speeds. Ran fine. Just continued to skip as we drove.


hi the engine is not skipping the problem is the engine is miss firing
that is caused by a bad .spark plug or -wires-or coil pack - when was the last time the
car had a tune up . check spark plug connections

Jun 12, 2011 | 2005 Nissan Altima

3 Answers

My 2000 Ford Expedition Triton motor has a skip. It doesn't do it all the time. The code says #6 misfiring. Is this something we can do ourselves or do we need to take to a shop?


You obviously have access to a code scanner so there are some things you can rule out and possibly fix the concern. Number six cylinder on the Exdedition is on the drivers side of the engine, second cylinder from the front. To do a backyard diagnosis, you will need to clear the code. This is easily done by disconnecting the negative battery terminal for 5 minutes then reconnnecting (I'll explain why). Next, remove the ignition coil on the # six cylinder. It is located on top of the engine and has one connector going to it and one small bolt holding it down, and usually black in color. You are marking it so that you don't mix it up. Now remove the # five ignition coil and install it where number six was. Put the marked coil in the number five hole. Connect both connectors.

Now drive the vehicle and allow the engine lamp to come on or to skip (misfire) a few times. Scan the vehicle for codes. If the code changes to a P0305 or # five misfire, then you know the ignition coil is bad. Replace the marked coil, disconnect the battery again to clear the code, then drive the vehicle and verify the repair. Other concerns could be a spark plug, injector, base engine concern or wiring. Good luck, let me know if you need more help :o)
Coils are the most common cause of misfire, especially after rain.

Apr 16, 2011 | 2000 Ford Expedition

1 Answer

Vsc & check engine light on. Code reads cylinder 2 misfire I have changed the plugs swaped coil with another cylinder swaped vsv's swaped injector plugs with another cylinder always shows misfire #2...


You may need to look at your exhaust system. If you have a leak, your O2 sensors will send the wrong reading to your engine which will in turn tell your engine to fire differently. Your code will come up reading as a misfired bank. See if you have an exhaust leak first, then see about changing out the O2 sensors behind the leak.

Jun 21, 2010 | Cars & Trucks

1 Answer

Truck is skipping and coil is bad, but was replaced once already what could be the problem if it is the same coil D


Which cyl has the skip and which coil did you replace? There are 8 coils? right? Replace the spark plugs with Motorcraft Spark Pugs ONLY.

May 13, 2010 | 2004 Ford F150

1 Answer

2000 F150 Supercab Skips and Backfires


Check the plug boots,to see if they are bad,or tune up is needed.Also can be a fuel pressure problem,change the fuel filter,if this does not help,have a fuel pressure test done,if there are any check engine lights on,have the codes read with a code reader,this will most likely tell on the problem.

Feb 10, 2010 | 2000 Ford F150 Flareside SuperCab

Not finding what you are looking for?
2005 Ford F-150 Logo

363 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...