Question about Ford Explorer

1 Answer

Reinstall transmission - Explorer Ford Cars & Trucks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

Make sure you put torch converter inside of trans be for you put it up. lift trans to bake of motor and lock in bell housing bolts
jack trans up and put cross bar and trans mount in .
go back to torch converter and install bolts to flywheel.
install dust cover then hook trans lines .
then install drive shafe then hook up shifter cable.
then put in your trans fluid

Posted on Aug 20, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install a torque converter in a 2000 2.5Lt on Ford ranger 2 wheel drive?


You need to remove the transmission to do this. Remove the inspection cover at the junction of the engine and transmission to get to the bolts to disconnect the torque converter from the drive plate (the part with teeth that the starter engages). Remove the driveshaft, then the transmission. The torque converter will come out with the transmission. Pull the old torque converter from the transmission, and install the new one. Ensure the torque converter goes all the way into the transmission/hydraulic pump. Reinstall the transmission, ensuring that the torque converter is still free to turn during the entire installation process, especially while drawing up the transmission to the engine. Once the transmission is bolted up, reinstall the bolts holding the torque converter to the drive plate. Reinstall the drive shaft and the inspection cover.

If you haven't done any major mechanical work on a car before, seek the help of someone who has. You will need a hoist or a jack and jack stands, and a good set of tools.

Nov 03, 2016 | Ford Cars & Trucks

1 Answer

Do I have to take the motor and trans out as one on a 2001 gmc jimmy


It is recommended, because there is only one mount on the transmission. Removal of the engine IS possible without transmission removal, but support of the transmission is difficult. It is also much more difficult to reinstall the motor and mate it with the transmission with the transmission already in the vehicle.

Nov 12, 2015 | GMC Cars & Trucks

1 Answer

Where are the transmission solenoids located on a 2003 2.2 liter cavalier


look under the air filter box. remove the air filter box exposing the top area to the transmission. on top of the transmission, you will see the transmission solenoid. box-like with three bolts. unplug harness's. get your drip pan, remove bolts,remove gasket, (razor blade needed) clean thoroughly around transmission (engine cleaner) before replacing with the new solenoid. reverse to reinstall. good luck

Feb 15, 2015 | 2003 Chevrolet Cavalier

1 Answer

How to install a slant 6 225 in a 1972 plymouth duster


Lower engine in bay, loosely attach motor mounts. Install transmission, mate to motor. Install transmission mounts, tighten motor mounts.
Hook up wiring and hoses. Fill all fluids. Reinstall driveline, hook up exhaust and linkage. Reinstall hood. Test work, check timing and carb settings.

Aug 29, 2012 | Plymouth Valiant Cars & Trucks

1 Answer

I am trying to replace the rear drivers side wheel bearing and hub assembly combined. I have having problems removing the hub assembly already on the car. What do i need to do to fix this problem


Remove offending wheel and set park brake extremely tight. Remove brake pads from caliper, and then unbolt caliper. Release the park brake. Unbolt the heater supply tube. Remove six 8mm hex bolts on the CV joint near the transmission. Remove axle. Remove four bolts on outside of housing that hold the 2 bearing race retainers. Reinstall new bearing into the housing... again this will require the EBS tool, and of course you'll have to rearrange the parts of the tool. Once the new bearing is installed, reinstall the bearing race retainers and the four screws that hold the retainers. Carefully reinstall the axle, making sure not to push the hub out of the bearing again.Reinstall six 8mm hex bolts holding the CV joint to the transmission. Reinstall rotor then set parking brake extremely tight.Reinstall brake caliper andl brake pads. Reinstall heater supply tube and wheel, torque wheel bolts to 96 ft-lbs, re-install transmission cover and suspension cover. Here you can find the quality parts http://www.carpartswarehouse.com/part/wheel-hub-bearing.html

Aug 29, 2011 | 1994 Saab 900

1 Answer

Tranmission gave out


It is 15 years old and it has done its job, it is OK for it to die now. You have to decide how much money you are willing to spend to fix a 500 dollar vehicle. Your choices are first to call around to transmission shops and ask how much they charge to rebuild your transmission or to swap a rebuilt for yours, and of course the labor to remove and reinstall. Another choice is to call around to junkyards, or recyclers if you prefer, and find a transmission which will fit, and came from a vehicle with much lower mileage. For goodness sakes do not get one shipped across country. Having that cost in mind call some shops and ask them the labor to remove the old and reinstall the replacement.
Myself I will not put a used wear item in a car, but many folks do. The warranty on a used transmission is to give you a replacement, not to pay labor for the second round of remove and reinstall. When you have the prices on those options, you will be able to make a choice, bear in mind the cost of just buying a 1999 Windstar.

Nov 17, 2010 | 1995 Ford Windstar

1 Answer

I need to replace the front transmission seal in my 1984 chevy s10 how do i do it


I'am assuming its an automatic, in any case the transmission has to come out, after thats done, slip torq converter out of trans, replace the pump seal and reinstall converter into trans, and reinstall trans. back into truck.

Jan 14, 2010 | 1984 Chevrolet S-10

1 Answer

Fy wheel Ring gear replacement


remove the transmission from the motor. unbolt the clutch if it's a standard... remove the flywheel bolts ... pull it off and reinstall the replacement... reinstall the clutch and transmission and you are done. two things to do first are to unhook the battery... and remove the starter.

May 27, 2009 | 1984 Ford Bronco II

1 Answer

Change Automatic Transmission oil


Honda's are drain and refill only.The filter is internal inside the transmission and can only be accessed during an overhaul.On the bottom of the transmission case is a drain plug that is gold in color.It is removed using a 3/8" ratchet,or extension with a ratchet atached.There is also an aluminum washer that must be kept track of and reinstalled with the drain plug or a leak will occur.After draining the trans,and reinstalling the drain plug,Honda genuine automatic transmission fluid,or an equivalent with a highly fricition modified additive must be used,or harsh shifting can occur.I would install about 3 quarts after draining,and start checking the level at this point.The fluid level is checked with the engine OFF,on level ground.

Nov 26, 2008 | 2004 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...