Question about 1998 Plymouth Voyager

1 Answer

TORQUE SPECS. AND PATTERN FOR PLYMOUTH 2.4 LITRE I4

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Are you asking for the wheel torque specs. or some other part of the car such as the engine head bolts etc.?
If it is the wheel lug nuts they are 80-100 ftlbs. and you should go in a criss-cross pattern. For example if you have 5 lugs nuts and the top one is say number one 1 I would go in a clockwise direction doing 1, 3, 5, 2, 4 then repeat. If you have four then it is 1,3,4,2. Hope this helps.

Posted on Aug 20, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the head bolt pattern for a 2006 suzuki forenza


usa car or where?
my guess you meant
head bolt torque sequence?

the factory FSM is $4 to read, posted 100s of times here.

1.4 L E-TEC I4 (petrol)
1.6 L E-TEC I4 (petrol)
1.8 L Family II I4 (petrol)
2.0 L Family II I4 (petrol) (my guess this???????))
2.0 L RA 420 I4 (diesel)

https://suzukipitstopplus.com/Products/1066-2006-forenza-reno-service-manual.aspx
4 buck so see staging rates , sequence and if TTY bolts
or if its angle set.

Sep 15, 2015 | 2006 Suzuki Forenza

1 Answer

What are the torque specs for head 1994 Plymouth acclaim 2.5


  1. Step 1 - tighten all 10 bolts to 22 ft. lbs. (30 Nm).
  2. Step 2 - tighten all 10 bolts to 45 ft. lbs. (61 Nm)
  3. Step 3 - re-tighten all 10 bolts to 45 ft. lbs. (61 Nm)
  4. Torque bolts No. 1 through 6 to 110 ft. lbs. (149 Nm)
  5. Torque bolt No. 7 to 100 ft. lbs. (136 Nm)
  6. Torque bolts No. 8 through 10 to 110 ft. lbs. (149 Nm)
  7. Re-tighten each bolt to its proper torque. Pay special attention to bolt No. 7; it should not be over tightened.

Feb 26, 2015 | Plymouth Cars & Trucks

1 Answer

What are the intake manifold torque specs on a 2008 suzuki sx4


which engine, you dont know that?

here is the lineup ,posted like 100 times.
1.5 L M15A I4 (petrol)
1.6 L M16A I4 (petrol)
2.0 L J20A I4 (petrol)
2.0 L J20B I4 (petrol)
1.3 L D13A I4 (diesel)
1.6 L DV6ATED4 I4 (diesel)
1.9 L D19A I4 (diesel)
2.0 L D20A I4 (diesel)

on USA cars, open hood, look up.see that EPA sticker
it tells you what is there.

Jul 02, 2014 | 2008 Suzuki SX4

1 Answer

Need torque spec for a 1998 3.1 litre chevy v6


Hi there:
Are you refer at engine torque specf? Please confirm us.

Aug 10, 2012 | 1998 Chevrolet Malibu

1 Answer

Need torque specs to replace head gasket on a 1989 plymouth voyager


Normaly supplied with the head gasket with the sequence in which to tighten them.

Jun 24, 2012 | Plymouth Voyager Cars & Trucks

1 Answer

Need head bolt torque specs for a 1992 Acura Legend 3.2 litre V6


The head should be torqued in 3 steps using a criss cross pattern beginning in the middle.
The final torque is 56 ft. lbs.. Good Luck..

Aug 21, 2011 | Honda Accord Cars & Trucks

1 Answer

Need to know the torque specs for 1993 voyager van cylinder head. 6 cylinder 3.0 litr


According to what I found online, the torque spec for the 1993 3.0L is 91ft/lbs, loosen and re-torque to 91 ft/lbs

This link is where I got the information, it is a PDF download

Good luck, Jim

May 01, 2011 | 1993 Plymouth Voyager

1 Answer

What is the torque specs for the transmission oilpan on a 98 plymouth grand voyager/


You don't really need exact specs on that but it is usually around 14 inch pounds... Just use a nut driver or 1/4 in drive ratchet and use a cross pattern on the bolts, not a circle. do not tighten anything 'till you have every bolt in and verify that it goes in easily. Be careful to not crush the gasket, after you get the fluid in, watch for seepage and tighten up wherever you see any . Most important to remove all old gasket material from both pan and trans rail that is the primary cause of leaks.

Jun 19, 2009 | 1998 Plymouth Grand Voyager

1 Answer

Need to the torque specs for a 1999 Dodge Durango


Head Torque sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs recheck final torque in sequence.

Torque intake manifold: Step 1: 12 inch/Lbs, (hand tight) Step 2: 72 inch/Lbs, (6) Ft/Lbs Step 3: 12 Ft/Lbs
torque intake plenum: Step 1: 24 inch/lb (hand tight) Step 2: 48 inch/lb (4) Ft/Lbs Step 3: 84 inch/lb (7) Ft/Lbs (To torque bolts, start in center using crisscross pattern)

Apr 07, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
1998 Plymouth Voyager Logo

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...