Question about 1994 Ford F250 Supercab

1 Answer

Need to change starter on 97' ford f-250. I was able to get everything unbolted but it is being held up by the motor mounting bracket. any suggestions on how to get starter out of the bell housing with out having to take out motor mount bolt and raise one side of the engine.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

Nope,remove bracket and use a scissor jack/block to raise engine.....or a hoist. (the people who design these cars dont work on them so why should they make it easy.....)

Posted on Aug 20, 2010

Testimonial: "thanks for the info."

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a A/C condenser


You have to remove the fan shroud and fan at the same time. Then remove the radiator and condenser at the same time. Usually 4 bolts for the shroud. The fan mounts the the water pump. You need the tool to remove it(parts store has it). A couple of brackets hold the radiator in place. Remove the hoses and lines going to the radiator and condenser, then lift them out. unbolt the condenser and reinstall everything.

Jun 21, 2015 | 2005 Ford E-250 Van

1 Answer

Replacing starter for 97 pontiac bonneville


i think if you unbolt the bottom of the front engine mounts and lift the motor up a little put a block of wood on top of a floor jack under the oil pan

Aug 13, 2012 | 1997 Pontiac Bonneville

1 Answer

Starter went bad on 1997 mystique. Need to remove it and put new one on. Not sure just how to take it out whether from the top or from the bottom or through a wheel well.


On the 2.0L remove the air intake resonators. Unbolt the starter electrical connections and mounting bolts and remove the starter from below. To install torque bolts to 15-20 ft lbs
On the 2.5L you will need to remove the air cleaner assembly to get at the support bracket which also needs to be removed from the engine and transaxle mount. Remove the fuel line support bracket at the accellerator bracket. You can then proceed to remove the starter motor bolts and electrical connections.

Nov 26, 2010 | Mercury Mystique Cars & Trucks

1 Answer

How do you remove a starter on a 1997 GMC Jimmy?


1995-97 4.3L MODELS and 1995-99 2.2L models

5ed4c74.jpg

Fig. 5: The starter motor on later model 4.3L engines is retained by two long bolts
  1. Disconnect the negative battery cable.
  2. Raise and support the front of the truck safely using jackstands.
  3. If necessary for access, disconnect the front exhaust pipe.
  4. If equipped, remove the starter heat shield.
  5. On the 2.2L engine, remove the brace rod from the front of the engine and the bell housing.
  6. On 2.2L engines, remove the drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well.
  7. Disengage the wires from the starter solenoid.
  8. On the 2.2L engine, remove the attaching bracket-to-engine mount bolt.
  9. Remove the starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you.
  10. Carefully lower the starter and shims (if equipped) from the vehicle.
  11. If necessary, remove the bracket (2.2L engine) or the shield (4.3L engine) from the starter assembly.
To install:
  1. If removed, install the bracket or shield to the starter, as applicable. Tighten the bracket nuts to 97 inch lbs. (11 Nm) or the shield nuts to 106 inch lbs. (12 Nm).
  2. Carefully raise the starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position.
  3. On the 2.2L engine, loosely install the bracket-to-engine mount bolt.
  4. Install the remaining starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm).
  5. Engage the wiring to the solenoid as noted during removal.
  6. On the 2.2L engine, install the brace rod and tighten the retainers.
  7. If disconnected for access, install the front exhaust pipe and tighten the fasteners.
  8. If equipped, install the starter heat shield.
  9. On 2.2L engines, install the drivers side wheel.
  10. Remove the jackstands and carefully lower the truck.
  11. Connect the negative battery cable.

Hope helps.

Sep 07, 2010 | 1997 GMC Jimmy

2 Answers

Where is the starter on a 1999 s-10


passenger side, under exhasut pipe, against motor, close to tranni.

Jul 17, 2010 | 1999 Chevrolet S-10 Pickup

2 Answers

How to change a starter on a 4.3 gmc sonoma 1997


STARTER REPLACEMENT ( 1995-97 4.3L MODELS )

ad8746e.jpg

Fig.: The starter motor on later model 4.3L engines is retained by two long bolts
  1. Disconnect the negative battery cable.
  2. Raise and support the front of the truck safely using jackstands.
  3. If necessary for access, disconnect the front exhaust pipe.
  4. If equipped, remove the starter heat shield.
  5. On the 2.2L engine, remove the brace rod from the front of the engine and the bell housing.
  6. On 2.2L engines, remove the drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well.
  7. Disengage the wires from the starter solenoid.
  8. On the 2.2L engine, remove the attaching bracket-to-engine mount bolt.
  9. Remove the starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you.
  10. Carefully lower the starter and shims (if equipped) from the vehicle.
  11. If necessary, remove the bracket (2.2L engine) or the shield (4.3L engine) from the starter assembly.

To install:
  1. If removed, install the bracket or shield to the starter, as applicable. Tighten the bracket nuts to 97 inch lbs. (11 Nm) or the shield nuts to 106 inch lbs. (12 Nm).
  2. Carefully raise the starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position.
  3. On the 2.2L engine, loosely install the bracket-to-engine mount bolt.
  4. Install the remaining starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm).
  5. Engage the wiring to the solenoid as noted during removal.
  6. On the 2.2L engine, install the brace rod and tighten the retainers.
  7. If disconnected for access, install the front exhaust pipe and tighten the fasteners.
  8. If equipped, install the starter heat shield.
  9. On 2.2L engines, install the drivers side wheel.
  10. Remove the jackstands and carefully lower the truck.
  11. Connect the negative battery cable.

Hope this help (remember rated this help) Good luck.

May 11, 2010 | 1997 GMC Sonoma

1 Answer

97 ford 150 4x4 starter replacement is there a web page to show this so i can get it done its cold and dont wana mess around


It's really not to hard except for the third bolt on top of the starter next to the block.

1. Disconnect the battery
2. Go under the truck on passenger side and unbolt battery cable at the starter. Thats all wires on the starter
3. Unbolt starter off trans housing. You will see the first two bolts the third one on top next to the block will take alittle time just hard to get to.
4. Bolt on top you will have to use extensions and go in from the passenger side motor mount area in the fornt and slide it through the opening of the motor mount to get to it. Extension length about 16" long.
5. Once you get it off replace the starter.
6. I would not reinstall the third bolt next to the motor it really is useless. Just another way of keeping you from working on your truck or car.

Feb 14, 2010 | 1997 Ford F150 Regular Cab

1 Answer

I'm repairing the oil pan but I can not remove it, how do I remove the transmission


Before you remove the transmission and not knowing the condition of your oilpan, I might be able to save you some trouble.
If you have a few leaks in the metal of the oilpan, JB Weld can be used without replacing a pan. If you have a stripped drain hole, there are oversized plugs and rubber expansion plugs for that problem.

Sometimes you need to turn the crankshaft to clear the rods. And you can clear the frame and the oilpump with the oilpan by loosening the motor mounts and trans mounts and lifting the motor and reblocking the motor mounts.

But if you want to still pull the trans out, you will pull the driveshaft, the trans linkage and dipstick pipe. Then unbolt the starter, torque converter, and finally every bolt on the trans case to motor block. Earlier you loosened the trans mount bolts, now the frame crossbar should be unbolted and everything should drop.

Dec 26, 2009 | 1997 Ford Aerostar Extended

2 Answers

How do I install starter for 2000 GMC Sonoma. This is a 4 cyl 2 wheel drive pick-up


e
Removal & Installation
2-Wheel Drive
- 2.2L Engine
  1. Remove or disconnect the following:
    Negative battery cable Front exhaust pipe, if necessary for access Starter heat shield, if equipped Brace rod from the front of the engine and the bell housing Drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well Wires from the starter solenoid Attaching bracket-to-engine mount bolt Starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you. Starter and shims (if equipped) from the vehicle Bracket from the starter assembly, if equipped

    e12f2d1.jpg

    Fig. Starter motor and related components - 2.2L engine

To install:
  1. Install or connect the following:
    Bracket to the starter, if removed. Tighten the bracket nuts to 97 inch lbs. (11 Nm). Starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position. Bracket-to-engine mount bolt (loosely), if equipped Starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm) Wiring to the solenoid Brace rod and tighten the retainers Front exhaust pipe and tighten the fasteners, if removed Starter heat shield, if equipped Driver-s side wheel, if removed Negative battery cable

Hope helped with this (remember rated this help) Good luck.

Nov 18, 2009 | 2001 GMC Sonoma Extended Cab

Not finding what you are looking for?
1994 Ford F250 Supercab Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...