Question about Nissan Quest

1 Answer

2004 quest alternator replacement....radiator removal or ac compressor?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Nissan Master
  • 1,075 Answers

Should not be any need for any of the above to be removed as alternator should either come up or go down under my advice is take a good look and you will see this can be achieved whthout the removal of any of these items.adrian,,,,,,,,,,,

Posted on Aug 20, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Year-old battery dead. Jump started fine, but security light stayed on solid while driving. Shut car off & battery dead again.


Sounds like there's a problem in the charging system. It could be as simple as a loose fanbelt, or as major as a bad alternator. I have a very similar car, 2004 Infiniti I35, same engine/alternator, and my alternator went bad in November. Replacement is a pain, the book calls for removal of the AC compressor, though my mechanic pulled the radiator instead.

Jan 25, 2016 | 2004 Nissan Maxima

1 Answer

2004 tsx acura not starting after a/c compressor was replaced. There is power and the engine turns over but it's not starting/catching. Any ideas?


make sure alternator electrical wire been reconnected because alternator has to be remove when replacing AC compressor if yes problem else where check for spark and fuel.

May 28, 2013 | 2004 Acura TSX

1 Answer

How to remove the alternator from a 2002 chrysler sebring without discharging the ac


alternator in tight spot,you need to loosen remove brace bolts you need brace with alternator.remove alternator pivot bolt and spacer and adjustment nut and bolt,when you remove alternator you have to angle it out through bracket by the AC COMPRESSOR. YOU DONT HAVE TO DISCONNECT ANY AC LINES OR COMPRESSOR TO REPLACE ALTERNATOR.

Nov 27, 2012 | Cars & Trucks

1 Answer

How do you remove the alternator from a 2004 Nissan Maxma?


3.5L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Right side engine undercover and side inspection cover
    • Radiator on Maxima
    • Radiator fan on 350Z
    • Drive belt
    • Alternator and A/C compressor harness connectors
    • Upper and lower alternator bolts
    • Alternator

Install or connect the following:

  • Alternator
  • Upper and lower alternator bolts. On Maxima tighten the upper bolt to 12-15 ft. lbs. (16 -20 Nm) and the lower bolt to 32-38 ft. lbs. (44-52 Nm). On 350Z, tighten the upper bolt to 48 ft. lbs. (65 Nm) and the lower bolts to 21 ft. lbs. (28 Nm).
  • Alternator and A/C compressor harness connectors
  • Drive belt
  • Radiator on Maxima
  • Radiator fan on 350Z
  • Right side engine undercover and side inspection cover
  • Negative battery cable
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 25; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

May 08, 2011 | 2004 Nissan Maxima

1 Answer

How do you replace an alternator from 2002 Mazda 626 V6 engine?


FIRST TURN OFF RADIO.REMOVE NEGATIVE BATTERY CABLE.REMOVE FRESH AIR DUCT.REMOVE RADIATOR UPPER BRACKET.REMOVE CONDENSOR FAN IF EQUIPPED.REMOVE ELECTRICAL CONNECTORS FROM THE ALTERNATOR.LOOSEN THE BELT TENSIONER LOCK NUT AND TENSION ADJUSTING BOLT.REMOVE ALTERNATOR UPPER MOUNTING BOLT.REMOVE RIGHT SPLASH SHIELD. REMOVE DRIVE BELT FROM THE ALTERNATOR PULLEY.REMOVE AC COMPRESSOR AND SUPPORT IT ASIDE LEAVING THE REFRIGERANT LINES CONNECTED.REMOVE ALTERNATOR THROUGH BOLT.THEN REMOVE ALTERNATOR.

Mar 01, 2011 | 2003 Mazda Mazda6

1 Answer

How to tighten belt on 2004 nissan quest


Best to remove the front passenger side wheel. Then snap out the clips that are holding the plastic cover towards the front. Now it will expose the belt area. Loosen the locking nut of the tensioner(idler) pulley located to the right of the Crankshaft Pulley. Crankshaft pulley is the one that handles both belts (alternator and the power sterring pump). Right to that next to it, upwards is the idler pulley. You will find the alternator pulley to the right of that further up. Open the hood of the van and locate the adjusting nut behind the alternator on the idler pulley from top and loosen that as well. Once both these are loosened, belt will loosen and will be easy to remove. Now replace it with the new belt the same way it was wrapped. Go over the crankshaft pulley; under the A/C compressor pulley; over the alternator pulley; under the idler pulley. tighten the adjusting nut from the top through the hood until the play on the belt (when pressed in) is less than 1 inch. Now lock the tensioner pulley by tightening the locking nut. Start and run the car for 15 mins to see if everything is ok.

Jul 28, 2010 | 2004 Nissan Quest

1 Answer

I cannot remove the alternator from a 2001 olds aurora


Is this a 4.0 or a 3.5?
I did a 3.5 recently and you need to remove the support over the radiator and then remove the radiator fans. You are supposed to move the AC compressor, however I was able to get the alternator our without doing that.

Nov 14, 2009 | 2001 Oldsmobile Aurora

1 Answer

What must be done to remove an alternator from a 2004 Kia Sedona? Does radiator have to be removed?


Yes, you'll need to remove the radiator. There are three bolts holding it on. 1 plug and 1 wire to a terminal with a 13 mm nut on it. It's a bear to get off. The only other way would involve removing the A/C compressor and removing the alternator from the bottom. I'm replacing a motor in a 2003 Sedona and it's tough!!!!

Sep 28, 2009 | 2004 Kia Sedona

1 Answer

How to change 1999 nussan quest ac belt


http://groups.yahoo.com/group/villagerquest/

Belt —A/C Removal
  1. Remove the A/C compressor drive belt.
    1. Loosen the A/C compressor drive belt pulley tensioner bolt.
    1. Loosen the A/C compressor drive belt idler pulley adjustment bolt.
40f6b66.gifInstallation
  1. sxv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Incorrect drive belt installation will cause drive belt failure.
    NOTE: Inspect the pulleys for warping or abnormal wear.
    NOTE: Make sure drive belt is properly installed on each pulley.
    To install, reverse the removal procedure.
    • Adjust the A/C compressor drive belt. For additional information, refer to Belt Adjustment—A/C .

Aug 10, 2009 | 1995 Nissan Quest

1 Answer

Having trouble getting water pump out of 94 lantra 1.8 lt


1. Remove the alternator & power steering pump drive belts.
2. Remove four (4) 10mm bolts holding the water pump pullys & remove the pullys.
3. Drain the Radiator (save coolant if intend to reuse).
4. Loosen & remove AC compressor belt.
5. Remove crankshaft pully (22mm bolt).
6. Remove lower timing belt cover (10 mm bolts) to access water pump bolts.
7. Remove the water pump (12mm bolts)
(1) Remove the 2 bolts, then remove the alternator brace (A). (2) Remove the water pump (B) and gasket.
dbb00ee.jpg ef0cc15.jpg 8. Clean mating surface on engine & install new gasket & pump - reassemble. Refill w/50-50 coolant.

Mar 21, 2009 | 2004 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

336 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...