Question about 2003 Chevrolet TrailBlazer

1 Answer

How to get to starter on 2003 traikblazer - 2003 Chevrolet TrailBlazer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,826 Answers

Removal & Installation 4.2L Engine To Remove:

  1. Disconnect the negative battery cable from the battery.
  2. Disconnect the brake booster hoses from the engine. Starter how to get to starter on 2003 traikblazer - gm-02-42-1398.gif

  3. Remove the positive battery cable and s-terminal lead from the starter.
  4. Remove the starter from the engine.
To Install:
  1. Install the starter to the engine. Tighten the nut and bolt to 37 ft-lb (50 Nm).
  2. Install the positive battery cable and s-terminal to the starter. Tighten the battery cable nut to 80 in-lb (9 Nm). Tighten the s-terminal nut to 20 in-lb (2.3 Nm).
  3. Connect the vacuum brake booster hose to the engine.
  4. Connect the negative battery cable to the battery.
5.3L & 6.0L Engines To Remove:
  1. Disconnect the negative battery cable from the battery.
  2. Raise and support the vehicle.
  3. Remove the rear steering gear crossmember from the frame. Starter gm-02-53-1399.gif

  4. Detach the wire harness from the transmission oil cooler line bracket.
  5. Detach the transmission oil cooler line bracket from the engine.
  6. Remove the right transmission cover bolt from the transmission cover.
  7. Detach the starter from the engine.
  8. Slide the starter forward and remove the transmission cover.
  9. Remove the heat shield from the starter.
  10. Position the starter so that it can pass between the engine oil pan and transmission oil cooler lines.
  11. Detach the starter lead and battery positive cable from the starter.
  12. Remove the starter from the vehicle.
To Install:
  1. Place the starter between the engine oil pan and transmission oil cooler lines.
  2. Attach the battery positive cable to the starter and starter lead. Torque the battery positive cable nut to 80 in-lb (9 Nm). Torque the starter lead nut to 30 in-lb (3.4 Nm).
  3. Install the heat shield to the starter.
  4. Attach the starter from the engine. Torque the bolts to 37 ft-lb (50 Nm).
  5. Install the right transmission cover bolt into the transmission cover. Torque the bolt to 80 in-lb (9 Nm).
  6. Attach the transmission oil cooler line bracket to the engine. Torque the bolt to 80 in-lb (9 Nm).
  7. Attach the wire harness to the transmission oil cooler line bracket.
  8. Install the rear steering gear crossmember onto the frame.
  9. Lower the vehicle.
  10. Connect the negative battery cable to the battery.
prev.gif next.gif

Posted on Aug 19, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I start my 2003 Honda odyssey van with a bad starter


Unless it is a manual transmission you can't start it unless you have a working starter motor, it is about a 1 hour job to replace the starter, a rebuilt starter is around $100.00 US at link 2003 HONDA ODYSSEY 3 5L V6 Starter Motor RockAuto

Jan 19, 2017 | Honda Cars & Trucks

1 Answer

Where is the starter located on a 2003 saturn ion


It is located about in the middle between the engine and the transmission. Also it is directly below the intake manifold. Hope this helps.

Jun 10, 2014 | 2003 Saturn ION

1 Answer

Where is the starter solenoid on a 2003 Mitsubishi Galant


It is located on the starter. I have included a picture of the 2003 galant starter showing which portion is the solenoid.

-Ben

9_14_2011_9_28_28_pm.jpg

Mar 18, 2011 | 2003 Mitsubishi Galant

2 Answers

Starter replacement on 2003 honda cr-v


will starter come out from bottom on 2003 honda cr-v 2.4 liter

Feb 09, 2011 | 2003 Honda CR-V

1 Answer

How to replace starter windstar 2003 V6 engine?


2003 Ford Truck Windstar 3.8L SFI 6cyl Repair Guide

Ford Windstar 1999-2003 - Starter Removal & Installation

  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
    NOTE When removing the hard shell connector at terminal -S-, grasp the plastic shell. Do not pull on the wire.
  3. Disconnect the starter electrical harness.
  4. Remove the upper starter bolt.
  5. Support the starter and remove the lower bolt.
  6. Remove the starter from the vehicle.

    e1d1735.jpg

  7. Fig. The starter is located at the lower front of the engine, and is visible through the air duct

To install:
  1. Position the starter in the vehicle.
  2. Install the upper and lower bolts. Tighten to 15-20 ft. lbs. (20-27 Nm).
  3. Connect the starter electrical harness. Tighten the starter cable nut to 80-124 inch lbs. (9-14 Nm).
    NOTE When installing the hard shell connector, be careful to push it straight on and make sure it locks in position with a notable click or detent.
  4. Lower the vehicle.
  5. Connect the negative battery cable.

I really hope helps with this (remember rated this help) Good luck.

Dec 31, 2009 | 2003 Ford Windstar

1 Answer

2003 es300 starter does not work


the starter solinoid is bad

Jul 20, 2009 | 2003 Lexus ES 300

1 Answer

2003 chevrolet venture will not start. Was running fine. shut it off / starter not engaging. Battery fine. suggestions?


You have a shortage or a bad starter. Tighten all bolts leading to battery and starter. If still giving you problems, remove starter take to auto shop have starter bench tested.

Jul 17, 2009 | 2003 Chevrolet Venture Passanger

1 Answer

Changing the starter on a 2003 Taurus


you need to remove it from the bottom front of car . disconnect the negative battery cable. remove the front splash shield from under front of car , working from under car take the protective cap off the wires that go to starter and then disconnect all wires from starter marking each one for propper reinstalation, remove the bolts holding starter and remove from under vehicle. replace in reverse order.

Nov 22, 2008 | 2003 Ford Taurus

Not finding what you are looking for?
2003 Chevrolet TrailBlazer Logo

446 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...