Question about 2007 Toyota Yaris

1 Answer

The brake light bulb isn't a typical bulb. It's pronged and I'm having trouble removing it from it's socket. Already struggled to remove it from the casing, now I just need to get the bulb in my hands. 2007 toyota yaris. Please help!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

This may sound stupid BUT wear a rubber glove to get a better grip and pull.

Posted on Aug 19, 2010

Testimonial: "Doesn't sound weird at all. After using some brute force I was able to finally pull the bulb out of the socket. Thank you anyway!"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake lights work but not the taillights


Since these are on separate circuits first check the front park lights and dash lights are going since these ARE on the same circuit. If not check the fuse. If that's ok, remove taillight bulbs and check they are not blown. You should be able to see the filaments between the prongs inside the bulbs. If they are ok with a test light check there is power going to lamp sockets with light switch on. If they are dual filament bulbs only one contact inside the light socket will have power going to it. The other contact is the brake light. You will need to identify it by getting someone to work the brake while you hold the test lamp on either contact with the light switch off then the other one is the taillight contact.

Aug 22, 2014 | Cars & Trucks

Tip

One Brake Light Not Working


Inspect Brake Light Bulb: The number one reason for a brake light operation failure is a failed brake light bulb. To check this condition access the bulb by removing the rear cover located in the trunk or rear compartment. Some cars allow you to remove the entire brake light lens to retrieve the brake light bulb. Once the bulb has been removed inspect the bulb filament. If it looks broken or if the bulb is smoked the bulb needs to be replaced. If you have replaced the bulb but it still doesn't work remove the bulb. With the key in the "on" position have someone hold their foot on the brake pedal and use a grounded test light to carful test the terminals inside the light socket. One of the terminals should illuminate the test light. (Note: Do not touch the outer metal ring that holds the bulb in place for it is grounded and can blow the system fuse if connected to the inner terminals.) If the test light illuminates reinstall the brake light bulb. While the brake pedal is depressed test the outer metal ring that holds the bulb, if power is present the ground lead from the light socket is bad. If the outer ring does not illuminate the bulb has failed and replacement is required.

Scan BCM for Trouble Codes: Some cars are equipped with a body control module or BCM this onboard computer controls and lighting signals and can malfunction not allowing the electrical current to continue to the brake light circuits. This condition is rare but it can happen. If you have performed all of the tests above and all results are positive scan the BCM for trouble codes if no codes are present try replacing the BCM.

on Dec 18, 2009 | Honda Civic Cars & Trucks

1 Answer

How do I remove the 3rd brake light housing on a 2004 Kia Sedona? Does it just pull off or do I need to remove the entire panel to replace the bulb?


Usually you can replace light bulbs without removing anything. You just pull back a panel in the trunk and the light have a plastic socket that twists to unlock it so you pull it out and replace the bulb in the socket. Then place the socket back in the light and twist it to lock it back in to place. It really simple. Head light need replacing but not typical tail lights.

Aug 13, 2014 | Cars & Trucks

1 Answer

2002 Hyundai sonata brake lights come on with driving lights on


Most common issue is that the wrong bulb(s) installed in one side or both rear brake lamp sockets I have seen a single prong bulb ,say a 1156 part # bulb installed and this car requires a dual prong connector bulb Hyundai part 18647-28088-L bulb in each side

Jun 23, 2014 | Cars & Trucks

1 Answer

Replacing brake light


Hi Edward-
The top brake light lens is held on with two size T25 Torx screws. You need a suitable size torx screw driver to remove (and again later replace the assembly) the two screws. Once the screws are removed (do not lose these), you can remove the entire lens assembly. You'll see the wires leading to the plastic bulb socket. The bulb socket twists off the assembly like a bayonet. Once the bulb socket is off, you'll be able to remove the bulb simply by pulling it straight out. Replace the bad bulb by inserting the new bulb and then reassemble your third brake light in the reverse order you removed it. Enjoy!

Apr 01, 2014 | 2007 Dodge Caravan SXT Minivan New Cars

1 Answer

When i push on my brake my dash lights and park lights and tail lights come on at the same time


The likely cause is a short in one of the brake light sockets feeding power back into the parking lights. Check both brake light sockets for heat damage. If no damage, remove the brake light bulbs one at a time to see if the problem is in the bulb or how it is fitting into the socket. If that isn't the problem, check the wiring behind the socket for a short between the wires.

Oct 25, 2011 | 1997 GMC Sonoma

2 Answers

Im looking for the fuse for the right tail light


You do not have a separate fuse for each side, if the left side works, replace the bulb in the right side that isn't working.

Jun 26, 2011 | 2002 Jaguar X-Type

3 Answers

How to change a tail light bulb in a honda element


Open the hatch and the tailgate.

Remove the two mounting screws with a Phillips-head screwdriver, and remove the taillight assembly from the body by pulling it back.

Determine which of the three bulbs is burned out: brake/taillight, turn signal light or backup light. (I assume you’ve already determined this)

Remove the socket by turning it one-quarter turn counterclockwise.

Pull the bulb straight out of its socket.

Push the new bulb straight into the socket until it bottoms.

Reinstall the socket into the light assembly by turning it clockwise until it locks.

Test the lights to make sure the new bulb is working.

When reinstalling the taillight assembly, first place the two pins in the holes in place. Tighten the two mounting bolts.

Hope this is helpful to you.

Jan 10, 2010 | 2003 Honda Element

2 Answers

2002 Toyota highlander passenger brake light not working


RE: 2002 Toyota Highlander 2.4cyl. 4X4 Base Model

I am a Certified Technician and have basic knowledge with electronics in electrical wiring. I searched the web and discovered this is a common problem.

I fixed the problem and it was a simple procedure... The problem is with the reverse light socket at the side with no brake light. This socket functions as a hub to direct current to the brake bulbs.

Remove reverse light socket and re-seat bulb. Check for loose or broken prongs. Replace if necessary.

Swap the reverse socket with the other side.

Oct 06, 2009 | 2002 Toyota Highlander

1 Answer

How to cchange the third brake light bulb


1992–98 GRAND AM AND ACHIEVA
  1. Disconnect the negative battery cable.
  2. Pull the center high-mount stop lamp cover to disengage the retaining tabs.
  3. Unfasten the lamp retaining screws.
  4. Remove the sockets using a suitable prybar to release the retaining tabs.
  5. Detach the bulbs from their sockets.
  6. Using a suitable prybar to release the tabs, remove the lamp lens. Fig. 14: View of the center high-mount stop lamp assembly — 1995 Grand Am and Achieva shown

Apr 04, 2009 | 1998 Pontiac Grand Am

Not finding what you are looking for?
2007 Toyota Yaris Logo

Related Topics:

323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...