Question about 2006 Mercedes-Benz B-Class

Open Question

Trying to replace the rear wiper arm but the locking nut is jammed

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace rear wiper arm on a 2009 Kia Rondo?


If you are replacing the entire arm assembly, there should be a plastic cover that will pry off exposing a nut that will have to be removed at the base of the wiper arm Remove the nut and wiggle the wiper arm up and down to help it release from the wiper motor pivot. Install the new arm in the proper location and retighten the nut

Jun 20, 2015 | Kia Cars & Trucks

2 Answers

How do I fix or replace the rear wiper motor


Hello,

  1. Disconnect the cable running to the negative terminal on the car's battery. To do this, loosen the nut on the cable clamp until the clamp is loose enough for you to slide the cable clamp off the negative battery terminal.
  2. Pull the wiper arm away from the rear windshield until the wiper arm locks into a vertical or semi-vertical position or is perpendicular to the rear windshield.
  3. Remove the nut holding the wiper arm assembly to the rear wiper motor.
  4. Pull the wiper arm off the wiper motor assembly.
  5. Unplug the rear wiper motor plug/harness.
  6. Remove the screws holding the rear wiper motor to the inside of the vehicle at the base of the rear window.
  7. Pull the rear wiper motor off.
  8. Install the new wiper motor and put the wiper motor and arm assembly back on the vehicle by reversing the completed steps.
From ehow.com

I hope this helps

Mar 21, 2011 | 2000 Ford Expedition

1 Answer

I remove the wiper arm & the outsdie lock of the shaft,remove the screws that hold the wiper motor inside, to I need to remove the 20mm nuts that hold the rubber seal outside the glass (in which I can...


IF YOU TALKING ABOUT REAR WIPER MOTOR REMOVAL YOU HAVE TO REMOVE PULL THE REAR WIPER ARM COVER BACK TO ACCESS THE WIPER ARM RETAINING NUT.DETACH THE NUT AND PULL WIPER ARM STRAIGHT OFF THE SHAFT TO REMOVE IT.

Nov 26, 2010 | 2000 Honda Odyssey

1 Answer

Wipers will not move, makes noise and there is power to the motor. Motor was replaced. Someone told me that the arms probably moved to far and are now stuck, how do I fix this?


Windshield Wiper Blade & Arm Removal & Installation Front To Remove:
  1. Mark the location of the wiper on the windshield.
  2. Remove or disconnect the following:
    • Nut cover
    • Nut from the wiper arm
    • Wiper arm
Wiper arm mounting nut gm_truck_s10_w-wpr-arm_ret-nt.gif
To Install:
  1. Install or connect the following:
    • Secure the wiper arm with the nut.
      1. Tighten to: 17 ft-lb (23 Nm)
    • Nut cover
Rear To Remove:
  1. Put the wiper arm in the park position.
  2. Remove or disconnect the following:
    • The washer hose from the connector
    • The cap from the wiper arm
    • The nut from the wiper arm
    • The wiper arm from the wiper motor shaft
Rear wiper arm mounting nut gm_truck_s10_w-wpr-arm_ret-nt_rr.gif
To Install:
  1. Install or connect the following:
    • The wiper arm on the wiper motor shaft in the park position with the wiper arm resting on the park ramp
    • The nut on the wiper arm
      1. Tighten the nut. Torque to: 17 ft lbs (23 nm)
    • The cap on the wiper arm
    • The washer hose on the connector

---
The wiper motor hopefully is ok, but if the wiper arms were not mounted at the right spot, it could have damaged the motor as it returned to the rest position, unfortunately.

If there is noise, the noise could be coming from the wiper arm joint being stripped out or the motor itself assuming that the ball joints under the hood and behind the firewall are still connected.

Check these items, and I'm sure you will get to the bottom of this.

Good luck on this repair.

Oct 08, 2010 | 1997 Chevrolet Blazer

1 Answer

I installed a new wiper motor. I ran it before installing the wiper arms. it will not stop at zero. it over travels down into the cowling. I try to rest them higher then they stop some where in the middle...


Try to run the motor without the wiper arms tightened down and turn it off so it can cycle down to its rest state. Then install the wiper arms.

Make sure, that the car's windshield wiper wiring is correct for this motor.
---
Wiper Arm & Blade Removal & Installation Front To Remove:
CAUTION
When the wipers are parked (off), the driver’s wiper arm must be above the passenger’s wiper arm.
  1. Remove the clip holding the outside end of the wiper arm cover to the arm.
  2. Lift the arm cap up to expose the nut.
  3. Remove the wiper arm mounting nut.
  4. Using a suitable two jaw puller, remove the wiper arm from the wiper pivot.
To Install:
  1. Verify that the wiper motor and linkage are in the parked position.
  2. Place the wiper arm in position over the wiper pivot.
  3. Install the nut to hold the wiper arm to the wiper pivot. Torque nut to 26 ft. lbs. (35 Nm). CAUTION
    Make sure to tighten the wiper arm nut properly.
  4. Push the arm cap cover down.
  5. Secure the clip holding the cover to the wiper arm.
Rear To Remove:
  1. Lift and hold the wiper arm away from the rear window.
  2. Lift the lock securing the wiper arm to the pivot.
  3. Slowly release the wiper arm so it rests against the lock.
  4. Remove the wiper arm from the pivot.
To Install:
  1. Install the wiper arm on the pivot.
  2. Pull the arm outward and release the lock.
  3. Gently release the wiper arm until it rests on the rear window.
prev.gif next.gif

Aug 22, 2010 | 1996 Dodge Grand Caravan

1 Answer

Replace the rear wiper arm shaft


There is a plastic cover that pops off at the pivot end of the wiper arm. pulling up on this with a hook of some kind from the furthest end should release it. Under it you will find a nut that holds the wiper arm to the shaft. It's quite common for the nut to come loose and the shaft spins without moving the arm. Try tightening this nut (with the ignition on, be sure the wiper motor is off, then turn off ignition and put the wiper arm in the parked position). This is a common problem if you've ever tried to turn on the wiper when it was frozen to the glass.

Feb 26, 2010 | 2000 Honda Odyssey

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

1 Answer

How to remove rear wiper arm from 2005 mazda


if there is a nut in the middle at the base of the arm remove the nut if there is no nut then lift the wiper arm away from the window and you will see a small tab that will pull away from the base of the arm pull this away and hold it while you let the wiper back down the wiper will hold the arm up and lock the tab out now gently pry or pull the arm off

Jan 11, 2010 | 2005 Mazda 6

2 Answers

Rear Wiper replacement


Normally, all you need to do, is lift the arm and slide a small locking tab into place. Then, just lift the arm off. If it doesn't work like this, it has a screw in the center.

Aug 06, 2009 | 2008 Kia Spectra5

1 Answer

HOW DO I REPLACE A REAR WINDOW WIPER ON 2005 FORD ESCAPE?


Remove the rear pivot arm.
Lift the pivot arm to the upright position.
Slide the locking tab out.
Pull up and remove the pivot arm.
Remove the rear wiper motor shaft nut cover.
Remove the rear wiper motor shaft nut.
Remove the rear wiper motor cover.
Remove the rear wiper motor bracket nut.
Remove the bolt and the rear wiper motor.

Jan 29, 2009 | 2005 Ford Escape

Not finding what you are looking for?
2006 Mercedes-Benz B-Class Logo

Related Topics:

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...