Question about 1992 Oldsmobile Cutlass Supreme

1 Answer

Directions of how to change a power steering pump

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers

Removal/Installation

  1. Disconnect battery ground cable.
  2. Disconnect inlet and outlet hoses from pump.
  3. Remove serpentine belt guard as necessary.
  4. Remove belt from pulley, using 1/2 inch breaker bar.
  5. Remove coolant recovery bottle as necessary.
  6. Remove pump assembly.
  7. Transfer pulley as necessary.
  8. Reverse procedure to install, them bleed power steering system as follows:
    1. Turn wheels all the way to left.
    2. Add power steering to Cold mark on fluid level indicator.
    3. Start engine and run at fast idle, then add fluid, if necessary, to bring level to Cold mark.
    4. Bleed system by turning wheels from side to side without hitting stops. Keep fluid level at Cold mark.
    5. Return wheels to center position and continue running engine for 2-3 minutes.
    6. Road test vehicle to ensure steering functions normally and is free of noise.
    7. Check fluid level and ensure level is at Hot mark after system has stabilized at its normal operating temperature.

Posted on Aug 19, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 gmc sierra half ton 4wheel drive changed out motor now power steering doesn't work even installed new pump still have no power steering


I am assuming you are using the same belt configuration as before. Is it possible the pulley for the pump is turning in the opposite direction?

Aug 13, 2012 | Cars & Trucks

1 Answer

I have a 1995 lexus Ls400.is there a way to tighten the power steering pulley without removing it.


  • xus LS 400 and locate the power steering pump pulley, fluid reservoir and pump on the upper front driver side of the engine.
  • 2 Connect the pulley remove tool to the front of the power steering pulley. Brace the arms on the pulley tool on the **** of the pulley. Connect the metal key in the middle of the pulley tool to the nut in the middle of the pulley. Connect the power drill to the pulley tool and pull the trigger to remove the pulley securing nut. Remove the drive belt and the pulley.
  • 3 Position the drain container under the power steering pump. Remove the drain plug from the bottom of the pump using the metric ratchet set. Let the fluid drain from the pump into the drain container. Replace the drain plug to the bottom of the power steering pump.
  • 4 Remove the securing bolts from the right and left side of the reservoir and the pump using the metric ratchet set. Pull the pump upward and disconnect the hose from the bottom of the pump using the wrench. Pull the pump from the engine compartment.
  • 5 Lower the new power steering pump into the engine compartment. Reconnect the hose to the bottom of the power steering pump. Position the new power steering pump onto the engine. Replace the securing bolts the right and left side of the pump and reservoir. Tighten the bolts using the metric ratchet set.
  • 6 Replace the power steering pump pulley the opposite way that you removed it. Reconnect the drive belt.
  • Fill the power steering pump reservoir with fresh power steering fluid. Start the engine and rotate the steering wheel to circulate the new power steering fluid. I no i gave you directions on how to remove the whole power steering pump question is the pully loose or are you wanting to just change a belt good luck happy holidays


  • Dec 15, 2010 | Lexus LS 400 Cars & Trucks

    1 Answer

    Seems like the power steering pumpis leaking, I have fluid below the truck and allover the top of the steering g ear box, cannot tellif it is leaking from the pump or the lines, I tried putting in Lucas...


    If this is around a 1999 F150, it is the Power Steering line going to the front steering oil cooler. There is a plastic clip which holds the line against the frame. Apparently it is a common problem. The plastic part seems to hold road salt and moisture against the metal and it corrodes.

    Change the line out or at least take it off and inspect it.

    Sep 05, 2010 | Ford F-250 Cars & Trucks

    1 Answer

    Removing power steering pump from v8 windsor


    Section 11-02A: Steering Pump, Power, C-II 1996 Aerostar, Ranger and Explorer Vehicles Workshop Manual REMOVAL AND INSTALLATION Pump and Pulley SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Steering Pump Pulley Remover T69L-10300-B Steering Pump Pulley Replacer T65P-3A733-C
    Removal
    1. Disconnect the power steering return hose (3A713) at the pump and drain fluid.
    1. Remove the power steering pressure hose (3A719) by unscrewing connector from the pump.
    1. On the Aerostar 3.0L V-6 engine (6007), loosen the drive belt tensioner (6B209) and adjustment bolts.





      Item Part Number Description 1 10346 Generator 2 8501 Water Pump 3 8678 Belt Idler Pulley 4 3A733 Power Steering Pump Pulley 5 6303 Crankshaft 6 2884 A/C Clutch 7 — Without A/C On the 2.3L I-4 and 4.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a counterclockwise direction. On Ranger 3.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a clockwise direction. Remove drive belt (8620) from under drive belt tensioner and slowly lower pulley to stop. Remove the drive belt from the power steering pump pulley (3A733).





      Item Part Number Description 1 10346 Generator 2 2884 A/C Clutch 3 3A733 Power Steering Pump Pulley 4 8501 Water Pump 5 6303 Crankshaft 6 8678 Belt Idler Pulley 7 6B209 Drive Belt Tensioner
    1. NOTE: If the drive belt requires servicing, refer to Section 03-05 .

      Remove the drive belt from the power steering pump pulley.
    1. Remove the oil dipstick tube.
    1. Remove the power steering pump support (3C511).
    1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley.
    1. NOTE: Do not apply pressure on the power steering pump rotor shaft (3B559). Pressure will damage internal thrust areas of the power steering pump (3A674).

      While holding the remover tool nut stationary with a wrench, rotate the inner spindle of the remover tool clockwise until the pulley is pulled off the power steering pump rotor shaft.
    1. Remove the bolts attaching the power steering pump to the A/C compressor mounting bracket (2882).
    Installation
    1. Install the power steering pump on the A/C compressor mounting bracket. Install and tighten attaching bolts to 41-61 Nm (30-45 lb-ft). On 4.0L engine, tighten to 47-64 Nm (35-47 lb-ft).
    1. Position the support on the A/C compressor mounting bracket. Install mounting bolts and tighten to 47-64 Nm (35-47 lb-ft).
    1. NOTE: Fore/aft location of power steering pump pulley on power steering pump rotor shaft is critical. Incorrect belt alignment may cause drive belt squeal or chirp. Make sure pull-off groove on power steering pump pulley is facing front and flush with end of shaft ± 0.254mm (± 0.010 inch).

      Install the Steering Pump Pulley Replacer T65P-3A733-C and install the power steering pump pulley.
    1. Install the drive belt on the power steering pump pulley.
    1. On the 2.3L I-4, Ranger 3.0L V-6, and 4.0L V-6 engines, position and rotate drive belt on engine. While lifting drive belt tensioner in a counterclockwise direction (clockwise on Ranger 3.0L V-6), slide drive belt under drive belt tensioner and lower drive belt tensioner to drive belt.
      On Aerostar 3.0L V-6 engine, position the belt idler pulley (8678) assembly to give the drive belt the tension specified. Refer to belt tension check in Section 03-05 . Tighten the drive belt tensioner and adjustment bolts to 47-64 Nm (35-47 lb-ft).
    1. Install the power steering pump support, if removed.
    1. Install the oil dipstick tube.
    1. Install the pressure hose tube nut and new Teflon® wagner into power steering pump valve outlet fitting (3D654) and tighten to 41-54 Nm (30-40 lb-ft).
    1. Connect the power steering return hose to the power steering pump, and reposition the clamp.
    1. Fill the power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent fluid meeting specification ESW-M2C33-F. Start the engine and turn the steering wheel (3600) from left to right without hitting stops to remove air from the system.
    1. Check for leaks and recheck the fluid level. Add fluid if necessary to proper level as specified in Section 11-00 .


      Power Steering Pump and Power Steering Pulley, 2.3L TPH Engine, Ranger Only





      Item Part Number Description 1 2882 A/C Compressor Mounting Bracket 2 N606543-S2 Bolt (2 Req'd) 3 N606069-S2 Bolt (2 Req'd) 4 N605803-S2 Bolt 5 N800199-S8M Screw 6 3D673 Power Steering Pump Pulley 7 3F671 Power Steering Belt Idler Support 8 N806020-S2 Bolt 9 3A674 Power Steering Pump 10 19703 A/C Compressor A — Tighten to 21.2-29 Nm (16-21 Lb-Ft) B — Tighten to 40.3-55 Nm (30-41 Lb-Ft) C — Tighten to 44-51 Nm
      (32-38 Lb-Ft)

      Power Steering Pump and Power Steering Pulley, 3.0L Engine, Aerostar





      Item Part Number Description 1 3A674 Power Steering Pump 2 3C511 Power Steering Pump Support 3 6007 Engine 4 N803564 Stud 5 N802827-S2 Nut 6 N800199-S8M Screw (3 Req'd) 7 N8011179-S2 Screw (3 Req'd) 8

    Jun 09, 2010 | 1996 Ford Explorer

    1 Answer

    How to change power steering pump on98 windstar with 3.8 engine


    fc582b7.gif
    3.8L Engine
    POWER STEERING PUMP Removal
    1. Remove the battery ground cable.
    1. sww~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR SYSTEM DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY . TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE POSITIVE BATTERY CABLE MUST BE DISCONNECTED PRIOR TO SERVICING OR REPLACING ANY SYSTEM COMPONENTS.
      Disconnect the positive battery cable and wait one minute for backup power supply energy to be depleted.
    1. Remove the drive belt. Remove the generator. Remove the power steering pump pulley as described.
    1. Position the drain pan. Remove the power steering pressure hose and the power steering return hose from the power steering pump .
    1. Remove the idler pulley.
    1. On vehicles equipped with A/C, remove the A/C compressor brace.
    1. Remove three bolts and the power steering pump and bracket assembly.
    1. Remove the retaining bolts and power steering pump from the power steering pump support .
    Installation
    1. To install, reverse the removal procedure.
      1. Tighten the power steering pump bolts to 40-55 Nm (30-40 lb-ft).
      1. Tighten the power steering bracket bolts to 40-55 Nm (30-40 lb-ft).
      1. Tighten the A/C compressor brace nut to 20-25 Nm (15-18 lb-ft).
      1. Tighten the idler pulley bolt to 40 Nm (30 lb-ft).

    Mar 10, 2010 | 1998 Ford Windstar

    1 Answer

    I need directions for changing the power steering pump


    1. Disconnect battery ground cable, then remove exhaust manifold heat shield.
    2. Disengage power steering pump reservoir hose from pump bracket and engine lifting bracket, then disconnect return hose and reservoir pump hose from pump.
    3. Allow fluid to drain into a suitable container, then raise and support vehicle.
      1. Remove lower belt guard, then rotate drive belt tensioner clockwise as viewed from direction shown, and remove accessory drive belt.
      2. Lower vehicle, then remove traction assist module bolts and position module aside.
      3. Rotate power steering pump pulley to gain access to each pump front mounting bolt, then remove three front bolts and one rear bolt and lift pump from vehicle.
      4. If it is necessary to separate pulley from power steering pump, proceed as follows:
        1. install power steering pump pulley remover T69L-10300-B, or equivalent, on pulley hub.
        2. Clamp hex head of tool in a suitable vise, then hold power steering pump in place while turning tool nut counterclockwise. Do not apply inward or outward force on power steering pump shaft, internal pump damage may result.
        3. Slide pulley from power steering pump shaft.
      1. Reverse procedure to install, noting following:
        1. If pulley and power steering pump were separated, install pulley on pump shaft using power steering pump pulley replacer T91P-3A733-A, or equivalent. Ensure threads on end of tool are fully engaged in power steering pump shaft; after pulley installation, ensure end of shaft is within 0.010 inch of being flush with pulley surface.
        2. When placing pump in vehicle, install rear mounting bolt first, but do not tighten until three front bolts are in position.
          1. Rotate drive belt tensioner clockwise as viewed from direction shown to install accessory drive belt.
          2. Refill power steering fluid reservoir and bleed system.

    Oct 08, 2009 | 1996 Ford Contour

    1 Answer

    Power Steering pump pulley


    You'll need a power steering pump puller available at most part stores. They are very easy to use and it should have directions in the package on proper use. Just think if you can do yours, you can do most of the domestics pumps out there.

    Jun 10, 2008 | 2004 Dodge Dakota

    Not finding what you are looking for?
    1992 Oldsmobile Cutlass Supreme Logo

    306 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Oldsmobile Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8210 Answers

    Are you an Oldsmobile Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...