Question about 2001 Ford Focus

1 Answer

Routing of idler belt - 2001 Ford Focus

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 117 Answers

Looks like this might be it, but if not go to the link at the bottom of the page. hope this helps

routing of idler belt - s7002.jpg

Search/Buy
Parts
From Catalog

http://www.bestvalueautoparts.com/Replacement_Parts/FORD/FOCUS/Illust_c_Belt_Routing.html

Posted on Aug 19, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a idler pulley on a 1997 international 4700 series


Hi Melissa:
Nice truck!
I'm assuming that the bearings in the idler pulley are shot which is why you're replacin the pulley. Pulley's are typically attached by a bolt through their centre. Replacing the idler consists of getting the bolt out and exchanging new for old. Here's the route I would recommend:
SAFETY FIRST - Disconnect negative battery terminal.
- Make a diagram of belt routing.
- Slacken idler and remove belt
- Remove Idler retaing bolt (Watch for washers or spacers)
- Install new Idler with washers or spacers in same position.
- Tighten retaining bolt.
- Use diagram to re-install belt;
- Re-connect negative battery terminal.
- Check for stray tools or loose objects.
Test run.

Mar 11, 2015 | Cars & Trucks

1 Answer

SERP BELT DIAGRAM 1997 ECOCOLINE 150 V 6 NOT 5.4 AS POSTED ON CORE SUPPORT? HAS 8 PULLYS A/C P/S / ALT /CRK /WATER PUMP, 2 IDLERS 1 TENTIONER. FACING ENGINE COMPARTMENT A/C TOP RIGHT P/S BELOW LEFT SIDE...


  1. Refer to the illustration for drive belt routing for vehicles with 4.2L engine with air conditioning.
    dq0142a.gif
  1. Refer to the illustration for drive belt routing for vehicles with 4.2L engine, without air conditioning.
    dq0143a.gif

Mar 08, 2011 | Ford E-Series Van Cars & Trucks

2 Answers

Drivebelt came off while on the highway (about 75 mph). Towed it home, went to replace belt and now both old belt (4 yrs old) and new belt (both 1025) are too long. Put on 1015 belt, topped off anti-freeze...


Hi, when a belt comes off, it's usually because of a bad bearing in one of the accessories or idler pulleys, or maybe your tensioner spring is broken. Remove the belt and check all pulleys for spin and play. It is also possible you lost an idler pulley and the new belt routing is not turning the water pump in the right direction. Check the routing and look for a missing idler pulley. Let me know if you are missing the routing diagram.

Feb 21, 2011 | 1988 Oldsmobile Delta 88

1 Answer

Replace serpentine belt



Removal & Installation

  1. Rotate the drive belt tensioner clockwise and remove the drive belt.
    WARNING Never suddenly let go of the tensioned idler pulley. The force of the spring pressure suddenly released may damage the idler pulley mechanism. Always release the spring pressure gradually.


    0996b43f80204f01.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Rotate the belt tensioner to relieve tension on the belt-4.6L engine shown, others similar


To install:
  1. Route the belt over the pulleys making sure all the grooves in the pulleys and the belt line up correctly. Refer to the accessory belt routing section of this manual.
  2. Rotate belt tensioner clockwise and slip drive belt over idler pulley on tensioner.

  1. Rotate the drive belt tensioner clockwise and remove the drive belt.
    WARNING Never suddenly let go of the tensioned idler pulley. The force of the spring pressure suddenly released may damage the idler pulley mechanism. Always release the spring pressure gradually.


    0996b43f80204f01.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Rotate the belt tensioner to relieve tension on the belt-4.6L engine shown, others similar


To install:
  1. Route the belt over the pulleys making sure all the grooves in the pulleys and the belt line up correctly. Refer to the accessory belt routing diagrams above.
  2. Rotate belt tensioner clockwise and slip drive belt over idler pulley on tensioner.
If for any reason, the tensioner is crooked, replace it!!! Also, install the belt with the writing facing you like you are trying to read a book. This WILL (a trick I learned at Mercedes) prevent even a new belt from squeeling!!

Dec 16, 2010 | 2003 Ford Explorer

1 Answer

What size is the engine on a 2002 dodge durango R/T? Need to change the surpentine belt.


4.7L or 5.9L and it should be listed on a sticker somewhere in the engine compartment.

---
Drive Belt Removal & Installation 3.7L, & 4.7L Engines To Remove:
dak_97-04_47l_drv_blt.gif

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect negative battery cable.
  3. Rotate tensioner until it stops.
  4. Remove belt and slowly rotate the tensioner back to its free position.
To Install:
  1. Install new belt and route around all pulleys except idler pulley.
  2. Rotate the tensioner arm until it stops.
  3. Route the belt around the idler pulley and slowly let the tensioner rotate back to its free position.
3.9L, 5.2L, & 5.9L Engines To Remove:
NOTE: Check the belt routing label, located in the engine compartment, for the most current belt routing schematic.
CAUTION
Do not attempt to check tension with a belt tension gauge on vehicles equipped with an automatic belt tensioner.
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Attach a socket wrench to the pulley mounting bolt of the automatic belt tensioner and rotate the tensioner assembly clockwise until tension is relieved.
  3. Remove or disconnect the following:
    • Belt from idler pulley
    • Belt from vehicle
To Install:
  1. Position drive belt over all pulleys except idler pulley.
  2. Attach a socket wrench to automatic belt tensioner and rotate the tensioner assembly clockwise.
  3. Install belt over idler pulley, allow tensioner to rotate back into place, and remove the wrench.
prev.gif next.gif

Sep 03, 2010 | 2002 Dodge Durango

1 Answer

2002 mustang GT serpentine routing


Hope this helps ya.. Cobra... :-)
f9fd01b.gif

Item Part Number Description 1 10344 Generator pulley 2 8620 Drive belt 3 8A528 Water pump pulley 4 3D673 Power steering pump pulley 5 63126 Crankshaft vibration damper 6 2E884 A/C clutch pulley 7 6B209 Drive belt tensioner 8 19A216 Belt idler pulley 9 19A216 Belt idler pulley

Jun 14, 2010 | 2002 Ford Mustang

1 Answer

Changing fan belt


Removal & Installation
  1. Rotate the drive belt tensioner clockwise and remove the drive belt.

    WARNING Never suddenly let go of the tensioned idler pulley. The force of the spring pressure suddenly released may damage the idler pulley mechanism. Always release the spring pressure gradually.

f897cde.gif
Rotate the belt tensioner to relieve tension on the belt—4.6L engine shown, others similar

To install:
  1. Route the belt over the pulleys making sure all the grooves in the pulleys and the belt line up correctly. Refer to the accessory belt routing section of this manual.
  2. Rotate belt tensioner clockwise and slip drive belt over idler pulley on tensioner.

Oct 11, 2009 | 1996 Ford Explorer

2 Answers

Problem with replacing serpentine belt on ml430


Routing can be a problem, wrong belt can be also as stated before. I had to take replace the idler pulley which i recommend doing when replacing the belt. I routed the belt then placed it into the idler pulley then slid the idler pulley onto the boss that that the idler pulley tightens onto. I thought it was the routing even took the belt back, but when i did the above I was done in 5 minutes after spending an hour an a half.

Mar 08, 2009 | 2007 Mercedes-Benz ML320 CDI

1 Answer

Serpentine belt routing


Here you go.. I looked up the same belt you did, it should be right.

adecd3f.png

Feb 09, 2009 | 2001 BMW 330

2 Answers

What is the serpetine belt routing for a 97 chevy tahoe 5.7 ?


looking down onto engine feed belt down to your left around crank pulley, route up putting back side of belt around w/pump then continue rest of belt around outside of remanning acc. leaving top idler last. put 3/8 drive ratchet into tensioner and rotate down slipping belt over idler

Dec 21, 2008 | 2004 Chevrolet Tahoe

Not finding what you are looking for?
2001 Ford Focus Logo

594 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...