Question about 2001 Ford Escort ZX2

Open Question

MI PROBLEMA ES COMO PONER A TIEMPO EL ARBOL DE ESCAPE DEL levas DE ESCORT ZX2 2001

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: como poner cadena de tiempo a motor de ford ranger 2003

Como loner el filtro de gasolina En 2003ford focus

Posted on Feb 26, 2011

Ad
ZJLimited
  • 17970 Answers

SOURCE: como colocar el tiempo de

Saludos, sugiero usar algun traductor para resolver estos detalles, obtenidos de un Boletin Tecnico de Servicio (TSB = Technical Service Bulletin)

A couple things you may want to be aware of, before getting too deep into this one:
(1) There is a factory recall under which the timing belt and sometimes tensioner components are replaced on this vehicle. you may want to check with the dealer to see if yours is still under an open recall for this; if so, they will replace the timing belt and any necessary related components for free. The recall is #01L002000 (description follows):

This is not a safety defect in accordance with the Safety Act. However, it is deemed a safety improvement campaign by the agency.

Vehicle Description: 1998-2000 Rodeo (UE) and Amigo (UA) models equipped with 2.2L 4-cylinder engines. The timing belt could break before the recommended scheduled maintenance.

This condition could cause the engine to crank but will not start or the engine could stall while driving and will not restart.

Dealer will inspect the vehicle to determine the condition of the timing belt and tensioner. The dealer will replace the timing belt. Depending on the condition or model of the timing belt tensioner, the tensioner may also be replaced. Isuzu has decided to conduct a Service Campaign to replace the timing belt. Owners can contact Isuzu at 1-800-643-4070, ext. 426, concerning this program

Second, there is a revised procedure involved in indexing the camshafts during timing belt replacement. This is most likely not detailed in your Haynes manual, but is outlined in an Isuzu service bulletin. Here is the procedure as described in the TSB:

BULLETIN NUMBER: IB00-S005
GROUP: INFORMATION
ISSUE DATE: FEBRUARY 2000

3.5L V6 DOHC (6VE1) / 3.2L V6 DOHC (6VD1) ENGINES: TIMING BELT INSTALLATION

AFFECTED VEHICLES: The following models equipped with "Direct Attack" DOHC 3.2L / 3.5L V6 engine:
^ 1998-2000 Rodeo (UE)/ Amigo(UA)
^ 1998-2000 Trooper (UX)
^ 1999-2000 VehiCROSS (VX)

SERVICE INFORMATION
This information bulletin outlines the proper steps to index the camshafts with the crankshaft. In the event that camshaft timing has been disrupted, due to timing belt breakage or camshafts/crankshaft being rotated without a timing belt, this is important prior to timing belt installation. Due to the gear-ratio used by each camshaft pulley to drive the camshafts, engine timing cannot be indexed conventionally.

SERVICE PROCEDURE

IMPORTANT: In the following procedures, the references to 9 or 12 O'clock positions are based on deck plane of the cylinder deck-to-cylinder head mating surface (as viewed from the front of the engine), and NOT RELATIVE TO THE SHOP FLOOR.

1. In the event that camshaft timing has been disrupted, due to timing belt breakage or camshafts/crankshaft being rotated without a timing belt, please proceed to Step 2. Otherwise, continue with Step 22 for timing belt servicing procedures. (after removal of front timing belt covers as outlined in the appropriate Workshop Manual).

2. After cylinder head servicing as outlined in the appropriate Workshop manual, proceed to the following steps.
3. Lubricate and install the idler gear.
4. Inspect the idler gear retaining cover for wear.

NOTE: There is a 0.039 lubrication hole drilled into the idler gear retaining cover. Always inspect this hole for obstruction.

IMPORTANT: Do not use a liquid gasket material on the idler retaining cover. Always replace the retaining cover with a new 0-ring. Be sure to lubricate the 0-ring prior to installation.

5. Install the idler cover and torque (10 Nm, 8 lb ft) the 6 mm bolts
6. Align the right bank idler shaft alignment marks.

IMPORTANT: Align the idler gear dowel pin to its corresponding mark on the idler gear retaining cover before installing the camshafts

7. Use special J-tool to pre-load the sub gear assembly.

NOTE: Use special J-tool J-42686. Once the sub-gear has been pre-loaded, install the 5 mm bolt supplied with the tool and insert it into the camshaft from the back of the camshaft gear assembly. Tighten the bolt to lock the sub-gear in place.

IMPORTANT: When the sub gear is pre loaded, the teeth on the sub gear should be aligned with the teeth on the camshaft gear.

8. Install the odd bank camshaft(s) into the cylinder head.

NOTE: Before installing the camshafts, pre-lube the cam lobes using a suitable molybdenum assembly grease

IMPORTANT: The single dot on the camshaft gears must be aligned with their corresponding marks on the idler gear. Also, do not remove the 5mm bolt holding the sub-gear, until the camshaft journal caps are installed and the bolts are torqued.

9. Install the camshaft journal retaining caps and torque (10 Nm, 8 lb ft).

IMPORTANT: The camshaft journal caps are numbered to prevent mis-matching. However, pay close attention when installing the caps on the odd bank cylinders. because the cap arrows will face the front of the cylinder head.

10. Place a small amount of RTV sealer on the head surface where the cap contacts the head surface.
11. Repeat Steps 3-5 for even bank cylinders.
12. Align the left bank idler shaft marks (Refer to figure 3).
13. Pre-load the sub-gear assemblies (Refer to figure 4).
14. Install the even bank camshafts and pre-lube the cam lobes using a suitable molybdenum assembly grease (Refer to figure 5).
15. Install the camshaft journal retaining caps and torque (10 Nm, 8 lb ft).

IMPORTANT: The camshaft journal caps are numbered to prevent mis-match mg. However, pay close attention when installing the caps on the even bank cylinders, because the cap arrows will face the rear of the cylinder head.


continue...

Posted on Aug 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Codigo de encendido de cadena del tiempo de intrepid 2002 2.7 motor


buenas noches me gustaria saber como van las cadenas de las levas para poner la cadena de tiempo gracias

Nov 11, 2012 | 2002 Dodge Intrepid

1 Answer

Poner a tiempo los arbol de levas


NECESITO SABER COMO PONER A TIENPO LOS ARBOLES DE LEBA DE UN MOTOR FORD EXPLORER 2004 4.0

Jun 11, 2012 | Suzuki XL7 Cars & Trucks

2 Answers

Como poner el tiempo de un toyota corolla del 94 de motor 1.6 gasolina y lo ocupo urgente


tienes que poner el cylindro numero 1 a TDC. en el cyclo de compresion del cylindro. pon el dedo en el abujero de la bujia y que le de vuelta alguien al motor, y cuando sientas que sale aire, entonces estas en el cyclo de compresion, despues ponle un desarmador largo al cylyndro y cuando le des vuelta al motor fijate que llegue el desarmador a la posicion mas alta antes de que se vuelva a bajar y entonces estas en TDC. Ya cuando estas en TDC, ponle la cadena de tiempo al carro y listo.

Jun 27, 2011 | 1994 Toyota Corolla

2 Answers

Marcas para poder sincronisar tiempo toyota corolla 94


en la polea del arbol de levas veras un hueco pequeño en una de las paletas, este debe apuntar a las 12 como el reloj y veras una marca en la primera abrazadera del arbol de levas , en cuanto a la polea del cigueñal , veras una marca en la parte lisa , debe estar alineada con un punto que sobresale de la tapa frontal del motor , creo que como a las 11 del reloj,eso es todo, cualquier cosa me escribes a mecanica03@hotmail.com

Sep 06, 2010 | Toyota Corolla Cars & Trucks

1 Answer

Mi tucson 2005 tiene problemas al arrancar. hay que intentar dos veces para que encienda


tengo problema con mi hyundai tucson 2005 de 4cilindros y 2.0cc
el encendido es lento como cuando rompe la correa del tiempo y al mucho rato de darle es que enciende con la marcha inferior a las 1000/RPM y a unos 5 segundos se apaga, le cambie la bomba de la gasolina, los inyectores, filtro del aire, estoy cansado de esto, que sera?

Mar 07, 2010 | 2005 Hyundai Tucson

1 Answer

La posicion dela banda del tiempo de caravan 3


como poner la banda de tiempo a una dodge grand caravan 1994,motor 3.0

Jan 17, 2010 | 1989 Dodge Caravan Cargo

1 Answer

Haw can change the band of distrubution?


ok sure you speak spanish because we says to timing belt = banda de distribucion. I will write in spanish :)

Lo que tienes que hacer con la banda de distribucion de tu Jetta 1994 es quitar las bandas externas de tu auto, luego de esto lo que tienes que hacer es quitar la polea del cigueñal para lo cual iras a requerir un extractor de poleas, ya que extraigas la polea del cigueñal y quites la tolva que guarda a la banda de distribucion y a los de los arboles de levas entonces gira con el maneral el cigueñal hasta las marcas del tiempo q deben estar marcadas en el motor o monoblock y/o en las tolvas, verifica estas marcas poniendo tu auto en punto muerto superior que es que el piston 1 quede hasta arriba lo puedes ver con un desarmador claro para esto tienes que quitar la bujia de tu auto del piston 1.

bueno ya que tengas esto prosigues a marcar la banda con alguna tinta o corrector tambien marca las poleas de los arboles o arbol y la del cigueñal, quita el tensor y va a salir la banda.

cuenta los dientes entre marca y marca y luego de eso marcalos en la nueva banda de distribucion. con el tensor de banda contraido pones la banda verifica que esten en sus marcas y luego vuelve a tensar la banda con su tensor.

si no sabes cuanto tensar solo verificar que la banda no debe doblar mas de 60 grados maximo 90 grados si gira mas entones esta floja.

ya puesta la banda verifica y dale 2 vueltas al cigueñal con el maneral y dado, si quedan en el mismo lugar las marcas luego de 2 vueltas completas de la polea entonces esta a tiempo si se atora se pone demaciado duro entonces las valvulas estan pegando.

vuelve a poner todo lo que desarmaste y listo!

Oct 16, 2009 | 1994 Volkswagen Jetta

2 Answers

Como poner cadena de tiempo a motor de ford ranger 2003


Como loner el filtro de gasolina En 2003ford focus

Apr 30, 2009 | 2003 Ford Ranger Regular Cab

9 Answers

Poner a tiempo cadenas de distribucion ford motor 4.0 mod 2002


11marzo2010- Necesito que me Hagan favor de enviar el diagrama para poner un motor de un tiempo de 4,0 Ford Explorer

Sep 14, 2008 | 2006 Ford Explorer

Not finding what you are looking for?
2001 Ford Escort ZX2 Logo

Related Topics:

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...