Question about 1996 Dodge Ram

1 Answer

Trying to bleed brakes is there a special size for this the 8mm is too big and the 7mm is too small

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Use standard sockets!!!!!!!!!!!!!!!!!!

Posted on Aug 19, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

What tool do I use to take off the break calipers to change brakes

9mm six point socket should be available from any good parts store or hardware.

Jun 12, 2015 | 2007 Ford Expedition Eddie Bauer EL

1 Answer

Rear brake pads

you will have to get hold of a 7mm allen for those bolts. and if the caliper still won't come off, you will have to force it as it is probably seized. use a screwdriver or a small pry bar to push back on the piston and pry the caliper off. make sure everything is clean and lubricated when you reassemble or it will soon seize up again.

Apr 04, 2013 | 2004 Dodge Grand Caravan

1 Answer

What size and type of screws are in the dashboard extension on the engine cover for a 2000 chevy astro van?

Small screws are 7mm, 8mm, and some are 9/32", and 7/32". The doghouse has 2 15mm screws way up in there, on the left top and right top.

Feb 05, 2011 | Chevrolet Astro Cars & Trucks

1 Answer

How do I bleed the brakes on the front?

on the brake brake calipper ther is a small fitting on it the size of the fitting bolt is 8mm or 10 mm loosen the bolt and then inser a transparent hose with a small emty bottle of brake fluid...just make a small hole on the bottle cup and insert the hose on it..someone will press the brake ten times then press it stedy and then open the fitting on the brake calipper repeat this proceedure untill u can see that there is no bubles comming out on the hose...but check the fluid bottle make it sure that there is always fluid on it....if u do the bleeding engine should be running......


Aug 03, 2010 | 2002 Chevrolet Tracker

3 Answers

What size allen wrench is needed to remove the Front Brake shoes on a 2002 Dodge Durango ?

I just did my front brakes yesterday and it needed a star drive ( torx wrech ) bit, not an Allen wrench

Jun 11, 2010 | 2002 Dodge Durango

2 Answers

How do you change brake light on my Audi avant 2003 as i cant seem to get into it ???

you should have a access point on the side of you trunk hatch small round piece pull it out. there is a screw back in there you will need either phillips screw driver or 7mm or 8mm socket to remove bolt. VERY carefully out assembly and there you go make sure to take not of the bulb there are two little knobs make sure whether they are straight across or offset this will make difference in how it fits good luck hope this helps

Jul 31, 2009 | 2004 Audi A4

1 Answer

Focus rear brake cylinder

it is usually a 8mm spanner but thruogh time they corrode down have you got a pair of vise grips if you do use them to grab bolt & slacken that way would also advise to replace rear wheel cylinder bolts too.

Mar 15, 2009 | Ford Focus Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

80668 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides