Question about 1996 Dodge Ram

Open Question

How to remove ignition switch from a 1996 Dodge Ram truck

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rockitman187
  • 2559 Answers

SOURCE: Need a free ignition wiring diagram for 1996 dodge ram 1500

See if this helps http://www.autozone.com/addVehicleId,2173802/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c1528007154c



Please rate this a fixya

Posted on Feb 15, 2009

emissionwiz
  • 75822 Answers

SOURCE: 1997 Dodge Ram 1500 transmission will a 1996 interchange

No, the frame is different.

Posted on Nov 30, 2008

mrgreenz
  • 962 Answers

SOURCE: hoe to Replace an alternator on a 1996 Dodge Ram Van 2500 3.9L V6

Remove negative battery cable.
Remove the electrical plug and wireing. Mark them.
Loosen the alternator pivot bolt.
Remove the bolt that attaches the alternator to the adjustment arm.
Rotate the alternator to loosen the drive belt and disengage the belt from the pulley. Be careful that any spacers that are used in mounting are kept with their original bolts. This will make correct reinstallation much easier.
While supporting the alternator remove the pivot bolt.
Remove the alternator from the vehicle.
Do the reverse procedure to install new alternator.

Posted on Feb 03, 2009

oneStan
  • 430 Answers

SOURCE: removing the transmission cooling line fron

These lines just run straight through the radiator to provide cooling. You can bypass the radiator by adding a transmission fluid cooler, during the cold weather in a pinch, a replacement transmission hose with 2 clamps can be connected between the 2 transmission lines to correct leakage, but in warm weather, the fluid suffers if it doesn't get the benefit of a cooler.

Aftermarket coolers are relatively inexpensive, especially compared to the long term benefit of keeping the fluid degrees cooler, prolonging the life of the trans.

good luck

Posted on Feb 22, 2010

  • 593 Answers

SOURCE: Remove headlight assembly from a 2001 Dodge Ram

On the upper grill side of the headlight assy. there
should be 1 or 2 push pins that hold the seal on the
headlight assy to the front of the fender. Also check
for a guide/push pin on the inner top of the assy on
the outer fender side. That should be all there is to
hold the headlight in place. Hope this helps.

Posted on Apr 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 dodge 1500 ram engine will not turn off after i turn off ignition and take key out


My guess would be a stuck relay or something with the key switch.
You could pull the relays to see if one will kill the engine, or check for power at the key switch.

Aug 21, 2012 | 1996 Dodge Ram 1500 Club Cab

1 Answer

1996 dodge ram electrical trouble


see the diagrams and troubleshooting flow chart: God bless you
7_25_2012_8_23_57_am.gif7_25_2012_8_24_35_am.jpg7_25_2012_8_25_17_am.gif

Jul 25, 2012 | Dodge Ram 1500 Cars & Trucks

1 Answer

I have a 1996 dodge ram 1500,the ignition won't start the truck or turn on the accessories.i have replaced the ignition switch but that didn't work.


is the battery dead or ist good check the voltage on it it should be arround 12.8 might be your alternator too

Jul 25, 2012 | Cars & Trucks

1 Answer

I have a 1996 Dodge Ram pickup. It just shuts


the ignition module,witch is in the computer.

Apr 30, 2010 | 1996 Dodge Ram

1 Answer

Ignition switch removal and replace how to on dodge ram 1500


lock and tumbler (key switch) remove steering wheel remove clockspring remove set screw remove switch...lower column ignition switch remove 2 screws and the rod unplug from harness replace in reverse just watch the rod placement

Mar 03, 2010 | 2004 Dodge Ram 1500

1 Answer

Rear door power lock--1996 Dodge Ram van (Roadtrek)-- won't open


Check all of your dash fuses inside the glove box if these are fine. Remove the door panel nd check to see that the wires have not come loose they tendto come loose from closing the rear door.

Mar 13, 2009 | 1996 Dodge Ram 1500 Club Cab

1 Answer

Engine will not start in 1996 dodge ram


check the adjustment on the switch rod try to start the engine by removing the rod and moving the ignition switch with a tool sounds like the rack in the column has slipped

Feb 09, 2009 | 1996 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

620 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...