Question about Subaru Impreza WRX STi

1 Answer

My wrx sti on a 53 plate is crunching into 1st and 2nd gear, the clucth bit point is right at the top. is this terminal, can it be fixed

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

Replace the clutch or you will be replacing the gearbox sooner than you want...do not skimp on just the friction plate do the whole kit...l

Posted on Aug 19, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 toyota Camry manual hard shifting from 1st to 2nd gear


With the engine off see if the shift between 1st to 2nd feel,s free if not it could be the cable check the clutch is disengageing all the way it should go into reverse without crunching,other then that it could be a synchro ring worn check that the gearbox has the right oil in it.

Dec 20, 2015 | 2008 Toyota Camry

1 Answer

Fiat seicento


The transmission needs work, possibly an overhaul.

Dec 03, 2013 | Cars & Trucks

1 Answer

How much does it cost 2 have a clutch replaced on a citreon xsara


Before you race out and replace the clutch which will not be cheap for your car have a good look at the slave cylinder for leaks . Check and bleed the clutch system and have the clutch m/cyl checked. Crunching gears means the clutch system is not disengaging properly

Apr 08, 2013 | Cars & Trucks

1 Answer

I put the wrong octane in my '08 wrx sti


all impreza recommends high ROM.
although 99ron or 100ron is recommended, some uses unleaded for non-turbo and of course notice a sligth defference in performance using high ROM fuel.
in your case is the reverse, means does't need to drain for a change.

Feb 18, 2012 | 2007 Subaru Impreza WRX STI Limited Sedan

1 Answer

My 2004 audi s4 makes gronchy noise when i put it in to 2nd gear when cold whats causing it?


If I've understood your problem correctly.....when changing from 1st gear into second the box is giving a metal on metal crunching sound?
  • This would be the syncromesh ring which is not equalizing the speed correctly.
  • The problem usually happens when there is wear on the same part.
  • Check to make sure that the correct transmission fluid has been used in the box.
  • To alleviate the problem and delay the time when it will require attention, use the double de- clutch method of changing gears, especially when the transmission is cold.
  • The double de-clutch is carried out in the following way.
  1. When in gear and changing from 1st gear to 2nd, change into neutral and release the clutch and then depress again before selecting 2nd gear....It is not required to rev the engine in the neutral position when changing up....
  2. When changing down rev the engine when the shift lever is in neutral for each change.
You'll soon get the hang of it and stop the crunching sound, protecting the box at the same time....
Regards Johngee

Nov 13, 2010 | 2004 Audi S4

1 Answer

How do you know what ratio a subaru wrx gearbox is if it doesn't have a trans code sticker on it?


This information is from my genuine service manual. I hope it is of help.
Non-turbo
Turbo
Sedan Wagon
Type 5-forward speeds with synchromesh and 1-reverse
Transmission gear ratio
1st 3.454 3.454
2nd 2.062 1.947
3rd 1.448 1.366
4th 1.088 0.972
5th 0.780 0.738
Reverse 3.333
Front reduction gear Final
Type of gear Hypoid
Gear ratio 4.111 3.900
Rear reduction gear
Transfer
Type of gear Helical
Gear ratio 1.000 1.100
Final
Type of gear Hypoid
Gear ratio 4.111 3.900 3.545
Front differential Type and number of gear Straight bevel gear (Bevel pinion: 2, Bevel gear: 2)
Center differential Type and number of gear
Straight bevel gear
(Bevel pinion: 2, Bevel gear: 2 and viscous coupling)
Transmission gear oil GL-5
Transmission gear oil capacity 3.5 2 (3.7 US qt, 3.1 Imp qt)

Mar 21, 2010 | 2007 Subaru Impreza WRX Sport Wagon

1 Answer

Trouble changing gears 1st and 2nd


If the clutch feels firm with no play u may have worn syncronizer's in the trans, take it to trans shop and have them road test it, they will not charge in most cases.

Jan 21, 2009 | 2002 Daewoo Nubira

1 Answer

I cant remove my key from the ignotion 04-05 wrx sti


You are going to have to have you ignition tumbler replaced. (Talk about insult to injury!) It sounds like Repo-man slammed in a new tumbler to snatch your rex and didn't quite get it in right.
Good luck!

Jan 05, 2009 | 2007 Subaru Impreza WRX STI Limited Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...