Question about 2003 Jaguar X-Type

1 Answer

Car jerks when starting from a stop. Engine symbol shows on dashboard and states "CRUISE NOT AVAILABLE" when none of the cruise control buttons were not pushed. Car drives fine after getting started but engine symbol on dash stays on.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 117 Answers

You need to have your obd3 Diagnostic Trouble Codes read Most auto parts stores will do this for you. This will give you a better idea where to start.

Posted on Aug 19, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My cruise control on my 2001 Kia Sportage stopped working.


Check your repair manual where the vacuum hoses for the cruise controls are (engine bay). Maybe one of the hoses came off or has a leak.

Feb 29, 2016 | 2001 Kia Sportage

1 Answer

What does the MIL code "PO 320" mean, please?


code p0320 refers to cam shaft position (CKP) sensor/engine speed (RPM) sensor--circuit malfunction=== causes --wiring--CKP/RPM sensor ---ECM
because the engine runs ok until it is on cruise control I would be investigating the RPM sensor for a fault
The cruise control takes its control from the RPM sensor and if that circuit is interminable the the cruise control doesn't know what rpms to maintain.

Jan 29, 2015 | Cars & Trucks

2 Answers

Cruise control not working


Most Likely just a blown fuse. It's normal to put that on another system fuse, like the hazard or AC fuse.

Sep 24, 2014 | 2007 Peugeot 407 SW

1 Answer

2003 oldsmobile alero v6 -- cruise control stopped working...The cruise on/of button lights up, the green light cruise indicator comes on in the dash panel, but cruise control does not engage when CST SET...


Try checking the small switch at the top of the brake pedal. There may be two one for brake lights and one for the cruise control. To ascertain what is what, pull one wire off and see if brake lights work. If not, then the other switch controls the cruise control disconnect and engage..I you have a DC test light check to see if power is on on both side of the switch with brake pedal up. If so, depress pedal and check power on the other side there should be none, if there is the switch is defective.

Aug 02, 2017 | Cars & Trucks

1 Answer

Cruise control stopped working


no year stated, wow.
the first checks are not the CRUISE.
they are:
1: all fuses good.
2: CEL lamp out driving, if not the PCM will in fact cut Cruise function ( preventing TOYOTA SYNDROME)
3: scan tool do a full PCM scan, got errors. got DTCs, bingo.

today cruise is the last to work, (a very serious safety issue)

Sep 23, 2013 | Honda Odyssey Cars & Trucks

1 Answer

I have a 1999/2000 volvo v40, a green dashboard light has come on, looks like a clock but the hand is outside, looks to be pointing at the 9 or 10, any idea's, iv'e lost my book!


That's the cruise control. Green symbol means that it's enabled.

There is a double button on the tip of turn-signal switch. Pressing plus or minus freezes current speed and you may apply some relax to your leg. A speed tuning is possible using this button(s). There's also a switch that disables the feature. If you are forced to slow down or stop, you may run the car again and restore previously set speed using "Resume" function on this switch.

Cruise control switches immediately to manual control after touching the brake or clutch pedal.

Cruise control doesn't work at very low speed and is not recommended in streets woth heavy traffic.

Jul 02, 2013 | Volvo V40 Cars & Trucks

2 Answers

I dont know the meaning of a light on my dashboard


This symbol is just on to tell you that you have the cruise control on, when the cruise is on this symbol lights up to tell you it is on, when you turn off the cruise the light will go out , hope this helps good day

Dec 23, 2012 | 2001 Toyota Corolla

1 Answer

My cruise controll has stopped working and my dashboard lights have stopped working also. All of my idiot lights work including the turn signals. I just cant see the speed at night! Please help


The Dashboard light dimmer control is probably stopped working because one of the tiny eletronic bits inside it has died. A temporary fix is to remove the connecting plug on the rear of the unit and put a bridging wire across the terminals. The cruise control problem could have several causes. They operate on engine vacuum so check the hose going to the cruise control unit in the engin bay from the inlet manifold. If the hose is cracked or hard there will not be enough vacuum to operate the cruise control.

Aug 18, 2010 | 1999 Ford Crown Victoria

2 Answers

I own a 2005 GMC Canyon Five CYL and the cruise control stopped working last niight. You push the button and no cruise. I checked the fuse and it is ok I exchanged with another 10AMP and no change still...


Start with the simple and check the fuses and the Stop lamp switch. Check your brake lights, if they're not working, the cruise won't work either. If they're not working, check the fuse for them, if the fuse is fine, then take it into the dealer, there's been a recall issued on the brake switch, so it should get fixed for free.
Cruise Control Disengaged
The powertrain control module (PCM) disengages the cruise control operation based on the signals from the following switches:

* The stop lamp switch
* The TCC brake/cruise release switch
* The clutch release switch, if equipped
* The cruise control On/Off switch

The TCC brake/cruise release switch and the stop lamp switch are mounted on the brake pedal bracket. When the brake pedal is applied, the normally closed TCC brake/cruise release switch opens and the normally open stop lamp switch closes. The PCM detects a low signal voltage on the TCC brake/cruise release switch signal circuit and a high signal voltage on the stop lamp switch signal circuit. When the clutch pedal is applied, the normally closed clutch release switch opens and the PCM detects zero voltage on the CCP switch signal circuit. The vehicle speed stored in the memory of the PCM will be erased when the cruise control On/Off button is turned OFF, or the ignition switch is turned OFF.

The Cruise Control System will disengage when the PCM detects that a driver override function has been active for approximately 60 seconds .

When the Cruise Control System is disengaged, the PCM sends a class 2 message to the instrument panel cluster (IPC) in order to deactivate the cruise control indicator.

Cruise Control Inhibited
The powertrain control module (PCM) inhibits the cruise control operation when any of the following conditions exist:

* A cruise control related DTC has been set.
* The vehicle speed is less than 40.2 km/h (25 mph) .
* The vehicle is in PARK, REVERSE, NEUTRAL, or 1st gear.
* The engine RPM is too low.
* The engine RPM is too high, with fuel cut off.
* The vehicle speed is too high, with fuel cut off.
* The system voltage is not between 9 volts and 16 volts .
* The Traction Control System (TCS) is active for more than 2 seconds .

Thank you for using Fixya and start with replacing the stop lamp switch. Even though the brake light work, it;s been known for that switch to cause your issue. that's way there was a recall for it.

Apr 01, 2010 | 2005 GMC Canyon

2 Answers

How to use cruies controw on a 1997 isuzu rodeo


First-on dashboard right hand side of steering wheel there are large (approx 1" sq) buttons-push to turn on-push again to turn off-for the rearwindow defroster,hazard flashing lights and....cruise control. Push cruise button to "on" and you'll see green lights on speedometer bezel light up. On end of wiper control stick on rightside of steering wheel-you'll find a pushbutton. Get car to speed you want-then push this button in. To turn off cruise control completely-push first button you pushed on dashboard.

Mar 21, 2010 | 1997 Isuzu Rodeo

Not finding what you are looking for?
2003 Jaguar X-Type Logo

548 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...