How is serpentine belt routed on 2006 mazda5 - 2005 Mazda Mazda5

That isn't the way to do it. You should have a bypass pulley, which keeps the route and the angles and the same length belt.

Details of bypass and the serpentine belt diagram in the link

https://www.google.com/search?q=2006+Nissan+Altima.+Serpentine+belt+diagram+no+air+conditioning&tbm=isch&ved=2ahUKEwiT2pXX38H0AhWQsHIEHZE8ARMQ2-cCegQIABAA&oq=2006+Nissan+Altima.+Serpentine+belt+diagram+no+air+conditioning&gs_lcp=CgNpbWcQAzoHCCMQ7wMQJ1CQGliJTmC4aWgBcAB4AIABa4gBnwiSAQQxMi4xmAEAoAEBqgELZ3dzLXdpei1pbWfAAQE&sclient=img&ei=0femYdOtEpDhytMPkfmEmAE&bih=937&biw=1920&rlz=1C1QJDB_enCA643CA644

..

Application:
With A/C

Kia_Sedona_2002-2006
Accessory Drive Belts

• ACCESSORY BELT ROUTING
• INSPECTION
• REMOVAL & INSTALLATION

Print

Accessory Belt Routing

Fig. Accessory serpentine belt routing-3.5L engine

Fig. Accessory serpentine belt routing-3.5L engine

Fig. Accessory serpentine belt (A) routing-3.8L engine

Inspection

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.

Removal & Installation

1. Disconnect the negative battery cable.
2. Rotate the auto tensioner clockwise to release tension, then remove the drive belt.

To install:

1. Install drive belt (A). Route the belt over the components in the following order: Crankshaft pulley - A/C pulley - idler pulley - generator pulley - water pump pulley - P/S pump pulley - tensioner pulley.
2. Rotate auto tensioner arm in the counter-clockwise moving auto tensioner pulley bolt with wrench.
3. After putting belt on auto tensioner pulley, release the auto tensioner pulley slowly.
   
   

   Fig. Accessory serpentine belt routing-3.5L engine
   
   
   

   Fig. Accessory serpentine belt (A) routing-3.8L engine
   

Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

• 2.4 Engine

• 3.3 Engine

• If you have any comments please feel free to leave them here.
• Hope this helps and thank you for using FixYa.

Regards, Tony

There are 2 possible engines for your car. The diagram for each is listed below. Best of luck!
Greg

2006 Sonata 2.4L Serpentine Routing:



2006 Sonata 3.3L Serpentine Routing:

Serpentine accessory drive belt routing-3.0L (VIN U, 2) Engines

Serpentine accessory drive belt routing-3.0L (VIN S) Engine

Here is the serpentine belt routing diagram for the 2006 Hyundai Tucson 2.7l V6:0


I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

here are a couple diagrams...




If you need anything else, let me know.

No such thing as a "starter belt". If they are refering to the belt that routes around the alternator, part of the power supplying system...then yes. But, this is only if you have 2 seperate belts. A serpentine belt is one entire belt that routes over all of the pulleys. Easy way to check, look at your belt. If you see one, it's a serpentine. If you see two, you have accessory belts. But, you should have a serpentine belt....1 belt.

Your motor has one belt, a serpentine...

there is a diagram of the belt routing under the hood of the car. I hope that helps you out.