2000 ford escort zx2 engine number 0g-774-aa. Is this a Zetec engine?

English only on Fixya!

Ford Escort (1997-2003) fuses and relays

https://fuse-box.info > ford > ford-escort-1997-2003-fu...
Fuse box diagram - In this article, we consider the third-generation Ford Escort, produced from 1997 to 2003. Here you will find fuse box diagrams of Ford ...

Ford Escort / Escort ZX2 (1997-2003) Fuse Diagram

https://fusecheck.com > Ford
Fuse box diagram (fuse layout), location and assignment of fuses and relays Ford Escort / Ford Escort ZX2 (1997, 1998, 1999, 2000, 2001, 2002, 2003).

ford escort/ focus engine 2.0 l spi sohc 1997-2004 has been identified as an intereference engine and that means very likely valve to piston damage
( auto data timing belt information )
note-- up to 2002 year Ford has not recommended a timing belt interval for changing
Ford has however recommended a replacement every 120.000 miles using the service history as a guide
however good professional trade practice recommends every 60.000 miles ( 100.00klms) and the replacement work should include replacement of the crank and cam shaft seals and idler pulleys involved ( the biggest destroyer of belts is oil)
recommended labor time is 2 hours
if the belt has broken then head removal and valve work will add up to 5 hours to that time

The picture is for a zetec. Let me know if wrong diagram?

[PDF]2000 Ford Escort Zx2 Service Manual

https://www.hellolibrary.org/2000-ford-escort-zx2-service-manual.pdf
2000 ford escort zx2 service manual (Korea Data Center [Miror II]). Speed 2389 kb/s ...the service pick at ... on all 2.0L, 4 cylinder engines

Automobiles: 2000 Ford Escort ZX2 4-cylinder 2.0L MFI DOHC

NOTE
The "left" side of the engine is the driver's side.

The Engine Coolant Temperature (ECT) sensor is a thermistor (a device which changes resistance or voltage as temperature changes). The sensor detects the temperature of engine coolant and provides a corresponding signal to the PCM (Powertrain Control Module - aka "the car's computer").

The ECT sensor is mounted in the following locations (small Ford engines):

1.8L engines: in the cylinder head
1.9L engines: threaded into the heater hose inlet pipe
2.0L engines: at the left rear of the engine

2.0L Zetec Engine

(1) Partially drain the engine cooling system using a clean container. If coolant is in good condition, retain for reuse.
(2) Disconnect the battery ground cable.
(3) Disconnect the electrical wiring connector from the engine coolant temperature (ECT) sensor.
(4) Remove the retaining clip and the ECT sensor.




Fig. 1 Escort ZX2 ECT sensor - The retaining clip is removed (at the solid arrow). Withdraw ECT sensor by gently wiggling/pulling in the direction of the dashed arrow.

To install:

NOTE
Coat the ECT sensor O-ring with clean coolant prior to installation.

(1) Replace the retaining clip and the ECT sensor.
(2) Connect the electrical wiring connector from the Engine Coolant Temperature (ECT) sensor.
(3) Connect the battery ground cable.
(4) Refill the engine cooling system. An inexpensive plastic "Radiator Funnel" will help with this task.

Zetec timing part 1

Zetec timing part 2

Sorry for the delay.
I am personally going back to answer your unanswered question. I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt/MARK(S) Diagrams that you will need, complete with Instructional and Directional Diagrams.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!
http://www.2carpros.com/car_repair_information/year/2000/make/ford/model/zx2/2000_ford_zx2_timing_belt_diagram_marks.htm

the engine will fit, u will need all the electronics and all drive train parts as well

I'm sure you've solved your problem by now, however your best bet is a junkyard.

you need this tool

OTC 6486 Ford Cam Tool Kit, 2.0L Zetec
Code:OTC6486
Price: