Question about 1997 Ford Expedition

1 Answer

When I get to certain speeds (50-60 mph) I check engine light starts flashing and the car starts jumping. I acts like it's going to cut out and I start loosing power. I still can excellerate but after the car stops jumping. Can you help me with this problem? Thank you so much!

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

When this happened to me. the vehicle needed a good tune-up. Had it done have not had the same problem since.

Posted on Aug 19, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check engine light is on, any speed above 30mph it gives a flashing check engine light, acceleration feels bogged down, engine idle is rough and shakes the truck


I'm guessing you have over 100000 miles , definitely replace all the spark plugs and ignition cables and cap and rotor if your motor is such equipped. If you want a better idea of which cylinders are misfiring, go to your local Checker or Autozone and ask them for code retrieval, codes stored will give you an idea of what is failing. Code po300 is multiple misfire, po301 is cyl #1, po302 is cyl #2 and so forth.

Mar 09, 2014 | 2003 Chevrolet Silverado 1500

1 Answer

2002 chevy s10 temperature gauge jumping around, feels like automatic transmission slipping at speeds above 60 mph


Do you have an OBDII scanner to check the real temperature? Want to make sure it's not overheating. If it's normal, could be your temperature sensor starting to go out, or ignition switch. Any check engine lights? If so, get the code for me, can go from there. At a constant speed, you sure it wasn't a misfire instead? Check your trans fluid, make sure it's full. I was just in Tahoe, pretty sad not much snow at all.

Feb 04, 2014 | Chevrolet S 10 Cars & Trucks

1 Answer

Tcs light flashes and p0340 code


P0340 code means "Something" is wrong in the timing...
from CMP (Camshaft Position sensor) to the crankshaft bolt.

Very first thing, verify connectors are clean and shiny.
clear all codes, even hard codes.

57f2e883-ce32-4061-b04b-ae0890f2c653.gif
612c4a6c-208f-43b8-8645-8318e85f9e48.gif
9e0c3051-1208-49b3-95d5-de3ff545fd3a.gif

Nov 23, 2013 | 2005 Mazda 6

1 Answer

Can't get it over 50 mph. It bucks hard and check engine starts flashing.


It could be bad spark plugs ,Or spark plug wires, Or fuel injecters, Or the motor has seen it,s better days, Depending on the mileledge on the vehicle, End if it was ever mantained (Properly)

Dec 06, 2012 | 2001 Toyota Tacoma

1 Answer

Replaced both speed sensors. changed fluid and filter in ******. still dont want to go into overdrive. acts like its stuck in 3rd gear and tacks around 4000 rpm going 40 mph


sounds like it's in default(2nd gear only) try key on engine off,press accelator fully four times ,this should clear the code then try it again,if it resets you will have to get the code.
Turn the key on-off-on-off-on and count the flashes of the check engine light ,for example 3 flashes then a pause then 2 flashes would be code 32.

Aug 11, 2011 | 1990 Dodge Spirit

2 Answers

I have 2001 bonneville. I was driving and stopped at a light and my service engine soon light starts flashing. My car acts like it doesn't want to pick up speed and it is shaking a little. Do you have any...


usually when the check engine light is flashing it indicates that you need to tune it up. I would replace the plugs and wires. Do it one at a time so you don't forget firing order. Leave comment

Apr 14, 2010 | 2001 Pontiac Bonneville

1 Answer

My check engine light is blicking and i cant go over 20 mph but the engine will get to 3000 rpm


sounds like a skip if the light flashes. your vehicle goes into a limp mode if it detects a problem to prevent further damage. this is why you cant go over a certain speed of rpm

Oct 03, 2009 | 2003 Hummer H2

1 Answer

Intermittent speedo for 1991 Honda accord but odometer & trip ok


its a faulty speed sensor or plug to speed sensor could be dirty

Dec 17, 2008 | 2001 Honda Accord

2 Answers

Speed sensor and overdrive


OVERDRIVE ENGAGEMENT IS TIED TO THE SPEED SENSOR SIGNAL, THE SYSTEM WILL NOT GO INTO OD UNTIL THE CAR REACHES A CERTAIN SPEED, IN MOST CASES AROUND 35-40 MPH, THE SPEED SENSOR SIGNAL TELLS THE ECU WHEN THE CORRECT SPEED HAS BEEN REACHED.

Oct 01, 2008 | 1991 Honda Accord

2 Answers

'97 Ford Ranger-Please Help!


IT LOOKS LIKE YOUR FUEL PUMP IS GOING BAD

May 29, 2008 | 1997 Ford Ranger SuperCab

Not finding what you are looking for?
1997 Ford Expedition Logo

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81423 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...