Question about 1993 GMC Suburban

Open Question

How do I bleed my brakes on my 1993 GMC Suburban

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6982 Answers

SOURCE: bleeding rear drum brakes

Take a small drill bit and clean out the center hole of both bleed screws (make sure you get all the way down into the hole, but don't go into the metal at the end.) Then, spray a good solvent into holes and on threads. Give some time for the solvent to soak in.
Put a six point box wrench on the bleeder then tap on the end of bleeder with a hammer. Keep doing this till it comes loose when turning the wrench. Don't use excessive force but don't be afraid to use enough force to get it to turn. Doing this, you will crush the tip of the bleeder, but that will not harm the "business end" Don't use vise grips on bleeders. At best you will damage flanks of nut portion, at worse, you will snap them off. Once you have removed bleeder, clean all rust off, make sure passageway is clear and re-install. If you do manage to break a bleeder, they can be drilled out, but it must be done carefully...if you damage threads or end seat it's officially junk. Bleeder screws are usually available at most parts stores...and, wheel cylinders are not very expensive if you need to replace one. Hope this helps!

Posted on Mar 25, 2009

Ad
  • 14036 Answers

SOURCE: 1996 Chevy Suburban rear brake fluid does not

if rear wheel drive the combination valve has be held open.you have to have a combination valve depressor tool .you need a scanner to do abs brake functional test.

Posted on Apr 27, 2009

  • 3 Answers

SOURCE: brakes won't bleed on a 2001 GMC Z71 four-wheel drive

check your calipers to make sure the bleeder is on the top! If not it will create a pocket of air in the chamber that won't bleed out!

Posted on Aug 31, 2009

  • 12 Answers

SOURCE: 1993 GMC Suburban has tranny problem. Checked

Vlv problems within the tranny. Try flushing tranny and changing filter. Other wise it may need be gone through.

Posted on Oct 10, 2009

Testimonial: "We are trying to see what we can do with out having to rip out the tranny. This may be helpful as we look at our options."

  • 12650 Answers

SOURCE: emergency brake stays on when fully disengaged

check the switch on the emergency brake pedal may need an adjustment or may need to be replaced

Posted on Jan 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to diagnose a bad brake boosterOn my 95 GMC Suburban K 1500 4 x 4 5.7 v8


Hi, your basic symptoms will be. Your brake pedal. Will be very hard to push. When the pedal is engaged there will be a large vacuum leak, usually causing the engine to be very ruff or stall. If its bad enuff, youll hear the the air leak when pedal is depressed, hope that helps.

May 02, 2016 | GMC Cars & Trucks

1 Answer

I need a bleeding sequence for a 1994 GMC Suburban


The proper sequence to bleeding any brakes, are usually to do the one farthest away from the master cyl. first, and continue till ur at the last one. (left front). Rear brakes, then to the front brakes!

Jun 30, 2014 | 1994 Chevrolet Suburban

1 Answer

I am having trouble bleeding the brakes on 1993 GMC Sierra. i can't find the compensator valve.


you can also bleed it right at the brake reservoir theres a bleeder valve there

Sep 12, 2010 | 1993 GMC Sierra K3500

1 Answer

Brake problem spongy brake pedal pedal goes down replaced front pads and master cylinder and wheel cylinder and bleed lines


try bleeding them more,start with the right rear,then left rear,then right front ,then left front, always bleed the brake that is furthest from the master cylinder, sometimes you have to bleed them several times until you get a steady stream of brake fluid.

Jul 29, 2010 | 1995 GMC Suburban

1 Answer

Replaced the front pads on my 99 suburban, but


pedal gets hard when turned of because they are power brakes plus theres no vaccum try bleeding the brakes if theres still a problem check the master cylinder and fluid level when brakes wear down they require more fluid but try first bleeding remember start at pass rear driver rear and pass front and last driver front

Aug 30, 2009 | GMC Suburban Cars & Trucks

1 Answer

1996 Chevy Suburban rear brake fluid does not bleed out when bleed valve is open


if rear wheel drive the combination valve has be held open.you have to have a combination valve depressor tool .you need a scanner to do abs brake functional test.

Mar 15, 2009 | 1996 GMC Suburban

1 Answer

ABS BRAKE LIGHT ON IN MY SUBURBAN/GMC TRUCK


Try diconnecting the battery for a minute or so, then reconnect it. the computer should reset itself, and hopefully the light will go out.

Jun 03, 2008 | 1993 GMC Suburban

Not finding what you are looking for?
1993 GMC Suburban Logo

Related Topics:

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...