Question about 1991 Ford LTD Crown Victoria

1 Answer

Is the starter hard to remove - 1991 Ford LTD Crown Victoria

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 135 Answers

NO , USE A 10 MM SWIVEL SOCKET FOR THE BOTTOM AND SIDE BOLT ,,USE 10 SOCKET AND 4'' EXTENSION TO REMOVE TOP BOLT USE 8MM SOCKET TO REMOVE SWITCH WIRE AND 13 MM TO REMOVENUT ON BATTERY CABLE TERMINAL OF STARTER

DONT FORGET TO REMOVE THE NEGATIVE BATTERY CABLE FIRST

Posted on Aug 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to replace the starter


remove the battery terminals, remove wires from starter, remove starter, replace with new starter, hook wires back up to starter and battery. Remember where the wires go as you take them off, once you mix them up, its hard to figure out where they went if you don't take a mental note or lable them with masking tape etc.

Dec 17, 2013 | 2003 GMC Envoy

1 Answer

Is it hard to change a starter on a 2008 Dodge Caliber?


NOT HARD YOU HAVE TO TURN OFF RADIO.DISCONNECT NEGATIVE BATTERY CABLE.REMOVE THE AIR INTAKE ASSEMBLY.REMOVE THE STARTER MOUNTING BOLTS.DISCONNECT THE THROTTLE BODY ELECTRICAL CONNECTOR. REMOVE THE THROTTLE BODY.PUSH THE STARTER UNDER THE INTAKE MANIFOLD.TIP THE NOSE OF THE STARTER TOWARD THE COOLING MODULE.PULL THE STARTER UP AND OUT.DISCONNECT THE STARTER WIRING.WHEN FINISH THE JOB.PUT EVERY THING BACK IN VISE VERSA.TORQE STARTER MOUNTING 40 FT LBS

Sep 12, 2010 | 2008 Dodge Caliber

1 Answer

Is it hard to get to?


STARTER NOT HARD TO GET TO YOU HAVE TO REMOVE AIR FILTER HOUSING REMOVE STARTER FROM TOP OF THE ENGINE.

Aug 20, 2010 | 2001 Ford Focus

1 Answer

Replace the starter


For 1997 Ford Aspire 1.3L EFI SOHC 4cyl check this procedure...

Removal & Installation
Models With Automatic Transaxle
  1. Disconnect the negative battery cable.
  2. Remove the two upper starter motor retaining bolts.
  3. Raise and support the vehicle using safety stands.
  4. Loosen the two intake manifold support bolts and remove the support.
  5. Loosen the support bracket bolts and remove the bracket.
  6. Loosen the starter motor support nuts and washers, then remove the support.
When removing the hard shell connector at terminal S, grasp the plastic shell. Do not pull on the wire.
  1. Disengage the S terminal connection from the solenoid.
  2. Loosen the B terminal washer and nut, then disengage the electrical connection from the solenoid.
  3. Loosen the lower starter motor bolt and remove the starter motor from the vehicle.
6884007.jpg

Fig. 2: Starter motor mounting and electrical connections-models with automatic transaxles (click for zoom)


To install:
  1. Position the starter in the vehicle.
  2. Install the lower starter motor bolt and tighten to 23-34 ft. lbs. (31-46 Nm).
  3. Engage the S and B terminal electrical connections.
When installing the hard shell connector, be careful to push it straight on and make sure it locks in position with a notable click or detent.
  1. Install the starter motor support and tighten the retainers to 35-44 inch lbs. (4-5 Nm).
  2. Install the support bracket and tighten the retaining bolts.
  3. Install the intake manifold support bracket and tighten the retainers to 12-14 ft. lbs. (16-22 Nm).
  4. Lower the vehicle.
  5. Install the starter motor upper retaining bolts and tighten them to 23-34 ft. lbs. (31-46 Nm).
  6. Connect the negative battery cable.

Models With Manual Transaxle
See Figure 11
  1. Disconnect the negative battery cable.
  2. Loosen the B terminal washer and nut, then disengage the electrical connection from the solenoid.
When removing the hard shell connector at terminal S, grasp the plastic shell. Do not pull on the wire.
  1. Disengage the S terminal connection from the solenoid.
  2. Remove the two starter support bolts.
  3. Loosen the starter motor support nuts and washers, then remove the support.
  4. Loosen the starter motor bolts and remove the starter motor from the vehicle.
807a17f.jpg

Fig. 11: Starter motor mounting and electrical connections-models with manual transaxles (click for zoom)



To install:
  1. Position the starter in the vehicle.
  2. Install the starter motor bolts and tighten to 23-34 ft. lbs. (31-46 Nm).
  3. Engage the S and B terminal electrical connections.
When installing the hard shell connector, be careful to push it straight on and make sure it locks in position with a notable click or detent.
  1. Install the starter motor support and tighten the nuts to 35-44 inch lbs. (4-5 Nm).
  2. Install the starter motor support bolts and tighten them to 14-18 ft. lbs. (19-25 Nm).
  3. Connect the negative battery cable.


Hope helps (remember comment and rated this).



Aug 05, 2010 | 1997 Ford Aspire

1 Answer

How to replace starter on 2000 ford windstar


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
    NOTE When removing the hard shell connector at terminal -S-, grasp the plastic shell. Do not pull on the wire.
  3. Disconnect the starter electrical harness.
  4. Remove the upper starter bolt.
  5. Support the starter and remove the lower bolt.
  6. Remove the starter from the vehicle.

    25fb386.jpg
    Fig. The starter is located at the lower front of the engine, and is visible through the air duct

To install:
  1. Position the starter in the vehicle.
  2. Install the upper and lower bolts. Tighten to 15-20 ft. lbs. (20-27 Nm).
  3. Connect the starter electrical harness. Tighten the starter cable nut to 80-124 inch lbs. (9-14 Nm).
    NOTE When installing the hard shell connector, be careful to push it straight on and make sure it locks in position with a notable click or detent.
  4. Lower the vehicle.
  5. Connect the negative battery cable.

Hope helps (remember comment and rated this).

Jul 14, 2010 | 2000 Ford Windstar

1 Answer

Remove the starter motor on a 2001 ford windstar


FIRST TURN OFF RADIO SO YOU WONT LOCK IT OUT.THEN REMOVE NEGATIVE BATTERY CABLE.RAISE AND SUPPORT VAN SAFELY.REMOVE THE HARD SHELL CONNECTOR AT TERMINAL S GRASP THE PLASTIC SHELL.DO NOT PULL ON THE WIRE.DISCONNECT STARTER ELECTRICAL HARNESS.REMOVE THE UPPER STARTER BOLT.SUPPORT THE STARTER AND REMOVE THE LOWER BOLT.REMOVE THE STARTER FROM VAN.THEN WHEN YOU PUT ON NEW STARTER TORQUE BOLTS TO 20 FT LBS.

Feb 21, 2010 | 2001 Ford Windstar

1 Answer

How to replace starter windstar 2003 V6 engine?


2003 Ford Truck Windstar 3.8L SFI 6cyl Repair Guide

Ford Windstar 1999-2003 - Starter Removal & Installation

  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
    NOTE When removing the hard shell connector at terminal -S-, grasp the plastic shell. Do not pull on the wire.
  3. Disconnect the starter electrical harness.
  4. Remove the upper starter bolt.
  5. Support the starter and remove the lower bolt.
  6. Remove the starter from the vehicle.

    e1d1735.jpg

  7. Fig. The starter is located at the lower front of the engine, and is visible through the air duct

To install:
  1. Position the starter in the vehicle.
  2. Install the upper and lower bolts. Tighten to 15-20 ft. lbs. (20-27 Nm).
  3. Connect the starter electrical harness. Tighten the starter cable nut to 80-124 inch lbs. (9-14 Nm).
    NOTE When installing the hard shell connector, be careful to push it straight on and make sure it locks in position with a notable click or detent.
  4. Lower the vehicle.
  5. Connect the negative battery cable.

I really hope helps with this (remember rated this help) Good luck.

Dec 31, 2009 | 2003 Ford Windstar

1 Answer

Need to replace the starter on the 97 mitsubishi Diamante, how hard is it to remove and replace ?


To replace the starter you need to;
) Note if you have an anti-thief system and now to reset it if the battery is disconnected.
) Note the radio station selections if they are not saved if the battery is disconnected.

Now
) Disconnected the GROUND connector on the battery.
) Disconnect the electrical cable on the battery.
) Remove the 2 bolts holding the starter on. Remove the harder one to reach first.
) Pull the old starter out.
) Insert the new starter.
) Replace the bolt. Insert the easier bolt first.
) Tighten the bolts.
) Replace the electrical cable.
) Reconnect the GROUND connector on the battery.
) Reset any radio, clock or anti-thief systems.
) Return old starter for a core charge refund.

May 25, 2009 | 1997 Mitsubishi Diamante

1 Answer

96 starter replacment


1st disconnect the battery there a few bolt that hold the plash guard after remove the 2 bolt holding the starter after the starter loose remove the big bolt that hold the batterycable and after the little on remove starter and reinstall good luck pierre

Mar 03, 2009 | 1996 Chevrolet Monte Carlo

1 Answer

Changing a starter


its not to hard to change disconnect battery .remove nut on front of starter to support bracket . remove 2 bolts going through starter into block. lower starter . disconnect wires on solonoid . remeber where they go. tools you will need 10mm 13mm 15mm sockets

Oct 22, 2008 | 1995 GMC Sierra

Not finding what you are looking for?
1991 Ford LTD Crown Victoria Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...