Question about 2001 Ford Crown Victoria

1 Answer

How do I remove the right front seat headrest in a 2001 Ford Crown Vic?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 488 Answers

Lift the headrest up, unscrew the two plastic covers from the post and then pull the headrest up.

Posted on Aug 18, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where where do i find the fuse for the speedometer on a 2001 Crown Vic


There are three fuse's for the instrument cluster , all located in the central junction box (fuse panel ) inside the vehicle ,under the dash !
Fuse # 14 a 10 amp , fuse # 23 15amp. and #6 15amp . Look behind right and left kick panel . But i don't think this is a fuse problem , gauge itself could be bad .

Dec 09, 2016 | 2001 Ford Crown Victoria

1 Answer

I have a 2001 Ford Crown Vic. I replaced the seats with 2002 seats. The air bag light is now on. The plugs are identical. Help


hope you saved the old seats.test your old sensors with a ohm meter then test the new seat sensor to see if they test the same.if they don't you will have to swap out the sensors

Feb 16, 2013 | 2001 Ford Crown Victoria

1 Answer

Front seat of 1993 crown vic is loose or broken


look under seat and u will ee the rails on each side of seat rock seat back and forth to locate wich bolt is loose or broken or if the rail itself is broken if rail broken remove the seat and order or go to a junkyard for the rail

Mar 02, 2012 | 1993 Ford Crown Victoria

2 Answers

How to remove the headrests to put seat covers on for a 1989 crown victoria?


90% of head rests just pull out. the others will have a button where the headrest goes into the seat. If yours doesn't have the button, then push the headrest down and **** it up with some force and it will come out. Just be carefull you don't hit yourself in the face with it. Been there done that

Feb 08, 2011 | 1996 Ford Crown Victoria

1 Answer

How do I remove the headrests from the front seats of a dodge stratus 2001?


There should be a small button on top of of the seat,
where the headrest bar go's in. Press and hold the
button while you remove the headrest.
Hope this helps. Good luck.

Jan 24, 2010 | 2001 Dodge Stratus

1 Answer

How do you remove a headrest from a 2001 mustang?


With the headrest about half way up insert a flat bar between the headrest bar and the opening where it goes in the seat. (back side of head rest) and pull up. It should come right out. I used a paint stir stick when I changed my seat belt loops.
Hope this helps.

Dec 26, 2009 | 2001 Ford Mustang

1 Answer

Headrest removal on a 1999 Ford Crown Victoria LX


If you unscrew the black pieces around the posts, lift them up and pull back gently on the seat material. There are 2 wire clamps around each post. Simply use a flathead screw driver and stretch the clamp to release the headrest.

Apr 21, 2009 | 1999 Ford Crown Victoria

1 Answer

How do you remove the headrest on a 1996 ford crown victoria?


Head Restraints Each front seat is equipped with dual-post design front seat back head restraint (611A08). The front seat back head restraint is installed as follows:
  • It travels on dual posts which have notches to engage a spring-loaded catch in the guide.
  • The front seat back spring assembly retains the front seat head rest guide rod sleeve (610A16).
  • The front seat back head restraint is adjustable from its normal position to a raised position of approximately 25 mm (1 inch).
  • Pull up on the front seat back head restraint to raise it. Pushing down will return it to its normal position.
----------------------------------------------------------------------------------------------

Removal
  1. Unscrew front seat head rest guide rod retainers (610A18).
  1. Pull up on front seat back head restraint (611A08). Compress foam in area of front seat head rest guide rod sleeves (610A16).
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves.
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve.

    Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint.

Mar 01, 2009 | 1996 Ford Crown Victoria

2 Answers

Location of fuel pump relay on a 2001 Ford Crown Vic


where is the fuel pump relay on a 2001 crown vic p71

Jan 10, 2009 | 2001 Ford Crown Victoria

1 Answer

Lay down backseat in Crown Vic Police Interceptor


The backseats of this vehicle do not fold down. They are placed on hooks and then they're bolted in on the bottom right and bottom left of the seat.

Jan 10, 2009 | 2001 Ford Crown Victoria

Not finding what you are looking for?
2001 Ford Crown Victoria Logo

285 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...