Question about 1994 Ford Ranger Supercab

1 Answer

To remove the right front axle shaft I remove the rotor and hub, will the axle shaft pop out of the differ housing.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

Most likely no. You will be able to get it out but may have to use a large screw driver to get the different end out carefully prying around the point where it installs in the differential.

Posted on Aug 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to repack front wheel bearings on a 98 Jeep Cherokee 4X4


YOU CAN"T is the short answer..... sorry,, RTM much>?
ive posted the free fsm like 300 times now on this car.
ever like search.?
first off, on all cars made, what the factory made or dealer sells ins one thing, what the after market does, is another.
a fact.
in fact some cars with Integrated hubs new, the aftermarket sells them and sells the rebuild kits too.
the book covers the service step by step.
what parts you use or by is your call.

now ill read that book for you.
btw I sold my 99 but not the books.
XJ jeep, the book is here, (over 301 posted,)

http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service

at least you said its 4wd, not all are. 2points for that.

USA XJ jeep, 1998.
1988 pages.
the trick is learning how to navigate the book , chapter #
the fact is we look first, you didn't, what is there who knows.?
maybe the last shop put on serviceable hubs. right?
if you had looked at the back side, you'd have seen 3 bolts
holding it on. and that tells you what?, that they are integrated hubs.
on new car, and at Jeep parts counters. world wide.



26271221-ky1blxw0v1am10ilppsnvnq2-3-0.jpgnow lets do this backwards
lets pretend to buy the part, hark , you can online.
and see all the makers of parts aftermarket in 1 click
no kidding, a fact.
see the 8 makers here,(can be more)
all are 100% integrated, hubs, (not saying there are not other makers, or kits, the world is a huge place and I cant tell you
all answers world wide for sources)

you could off them, take them both to a shop, and ask for them to rebuild them at $100 /hr labor, but, i bet they just laugh at you.
I'm not. but why not just remove it , check it and if bad replace it.
take it to any auto-store in town, NAPA is best. and set it on the counter, and say, got this, answer yes.
how to repack unpackable bearings,.DIY.

shorter answer, R&R it.
get a shop to fix it.
buy the part first, and see what you got first.
look at it and ponder packing it.

Aug 31, 2016 | 1998 Jeep Cherokee

1 Answer

How to remove axle from front of 1998 windstar


  1. Raise and support the vehicle safely.
  2. Remove the front wheels.
  3. Insert a steel rod into the brake rotor to prevent the rotor from turning and loosen the axle wheel hub nut. Discard the nut.
  4. Remove the ball joint-to-front wheel knuckle retaining nut. Drive the bolt out of the front wheel knuckle using a punch and hammer.
  5. Remove the front brake anti-lock sensor and position it out of the way.
  6. Separate the ball joint from the front wheel knuckle using a prybar. Position the end of the prybar outside of the bushing pocket to avoid damage to the bushing.
Use care to prevent damage to the front wheel driveshaft joint boot.
  1. Remove the stabilizer bar link at the front stabilizer bar.
Make sure the CV-joint puller does not contact the transaxle shaft speed sensor. Damage to the sensor will result.
  1. Install a CV-Joint Puller (T86P-3514-A1) or equivalent between the inboard CV-joint and the transaxle case.
  2. Install a CV-Joint Extension (T86P-3514-A2) or equivalent into the puller and hand-tighten.
  3. Using an impact slide hammer, remove the driveshaft from the transaxle.
Do not allow the front wheel driveshaft and joint to hang unsupported. Damage to the front wheel driveshaft joint may result. Do not wrap wire around the front wheel driveshaft joint boot. Damage to the boot may result.
  1. Support the end of the driveshaft and joint assembly by suspending it from the chassis using a length of wire.
Never use a hammer to separate the outboard front wheel driveshaft joint from the wheel hub. Damage to the outboard front wheel driveshaft joint threads and internal components may result.
  1. Separate the outboard front wheel driveshaft joint from the wheel hub using a Front Hub Remover/Replacer (T81P-1104-C) or equivalent. Make sure the hub remover adapter is fully threaded onto the hub stud.
Do not move the vehicle without the outboard CV-joint properly installed, as damage to the bearing may occur.
  1. Remove the front wheel driveshaft and joint assembly from the vehicle.
To install:
Do not reuse the retainer circlip. A new circlip must be installed each time the inboard CV-joint stub shaft is installed into the transaxle differential.
  1. Install a new retainer circlip on the inboard CV-joint stub shaft by starting one end in the groove and working the retainer circlip over the inboard shaft housing end and into the groove. This will avoid overexpanding the circlip.
A non-metallic mallet may be used to aid in seating the retainer circlip into the differential side gear groove. If a mallet is necessary, tap only on the outboard CV-joint stub shaft.
  1. Carefully align the splines of the inboard CV-joint stub shaft housing with the splines in the differential. Exerting some force, push the inboard CV-joint stub shaft housing into the differential until the retainer circlip is felt to seat in the differential side gear. Use care to prevent damage to the inboard CV-joint stub shaft and transaxle seal.
  2. Carefully align the splines of the outboard front wheel driveshaft joint with the splines in the wheel hub, and push the shaft into the wheel hub as far as possible.
  3. Temporarily fasten the front disc brake rotor to the wheel hub with washers and two lug nuts. Insert a steel rod into the front disc brake rotor and rotate clockwise to contact the front wheel knuckle, to prevent the front disc brake rotor from turning during front wheel driveshaft and joint installation.
A new front axle wheel hub retaining nut must be installed.
  1. Manually thread the front axle wheel hub retaining nut onto the outboard CV-joint stub shaft housing as far as possible.
A new bolt and nut must be used to connect the front suspension arm to the knuckle.
  1. Connect the front suspension lower arm to the front wheel knuckle. Tighten the nut and bolt to 40-55 ft. lbs. (54-74 Nm).
  2. Install the front brake anti-lock sensor.
  3. Connect the front stabilizer bar link and tighten to 35-45 ft. lbs. (47-65 Nm).
Do not use power or impact tools to tighten the hub nut.
  1. Tighten the front axle wheel hub retaining nut to 157-212 ft. lbs. (213-287 Nm).
  2. Install the front wheels and lower the vehicle.
  3. Using the recommended type of fluid, fill the transaxle to the proper level.

Jul 07, 2014 | 1998 Ford Windstar

1 Answer

How to remove the right side axel shaft on a 98 olds bravada


1. Raise and support vehicle, then remove tire and wheel assembly. 2. Install a brass drift or a screwdriver to prevent the rotor from turning, Fig. 7 . 3. Remove axle nut and washer. 4. Remove stabilizer shaft or link from control arm. 5. Remove nut from ball joint, then separate ball joint from steering knuckle using separator tool No. J-36226, or equivalent. 6. Remove drive axle from hub and bearing assembly using front hub spindle remover tool No. J-28733-A, or equivalent, Fig. 8 . 7. Remove drive axle from transaxle using axle shaft remover puller tool Nos. J-33008, J-29794 and slide hammer tool No. J-2619-01, or equivalents, if necessary, Fig. 9 . INSTALLATION 1. Install drive axle into the transaxle using seal protector J-37292-B, or equivalent 2. Seat snap ring by placing a screwdriver into the groove on the joint housing and tapping until seated, Fig. 9 . 3. Grasp the inner housing and pull outward. If the snap ring is properly seated, the axle will remain in place. 4. Install drive axle into hub and bearing assembly. 5. Install lower ball joint to steering knuckle and tighten to specifications. 6. Install stabilizer shaft or link to control arm, tighten to specifications. 7. Insert a screwdriver or drift into caliper and rotor to prevent rotor from turning, Fig. 7 . 8. Install new hub nut and washer, tighten to specification. 9. Install tire and wheel assembly, then lower vehicle

Feb 13, 2011 | 1998 Oldsmobile Bravada

1 Answer

How to remove rotor on rear of 2005 dodge 3500? Do I need special equipment?


If you truck has a standard rear axle just remove the caliper and caliper adapter bracket, then the rotor will pull off. Sometimes if the hub face is rusted it may take a little persuasion to come off. You can hit it with a ball peen hammer between the wheel studs, this is usually enough to free it. If you have a dually you will need to remove the axle shafts first by removing the bolts around the outside of the axle housing then pull the shafts outward. Then remove the caliper and caliper adapter. Slide rotor and hub assembly off of axle, then unbolt the the hub from the rotor.

Jan 20, 2011 | 2005 Dodge Ram 3500

3 Answers

My front differential is leaking!


I cannot see it, but I am guessing that you need to replace your axle seal. To do this,you have to pull your CV shaft out. Remove the tire, remove the caliper from the top of the rotor. Using a hammer on the back, remove the rotor. Take off the spindle (axle) nut, separate the axle (CV shaft) from the hub. Replace seal. It should pop right out. Good luck!

Aug 05, 2009 | GMC Sierra 1500 Cars & Trucks

1 Answer

How to replace front cv shafts ?


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Aug 01, 2009 | 1997 Isuzu Rodeo

3 Answers

Removing front axle 1991 ford escort


do you mean the drive shaft. if so you just need a good lever bar to prise the drive shaft out of the transmission.if you mean you want the drive shaft out of the front wheel hub then you may need a good pller to femove it as it can be very tight on the splines

Apr 22, 2009 | 1995 Ford Escort

1 Answer

Need to remove and replace rear rotor


You have to remove the axle shafts first as it has a full-floating axle, then pull rotor and hub off the axle housing. Unbolt rotors from hub. Check bearings and seals in hubs and the axle snouts where the bearings run before installing. Put new flange gaskets on axle and torque flange bolts to 95 ft-lbs.

Apr 11, 2009 | 2004 Dodge Ram 3500 Truck

1 Answer

Replacing front wheel ujoint on 2001 ram dodge 1500


HUB BEARING AND AXLE SHAFT REMOVAL
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake components from the axle, Refer toBrakes.
  4. Remove the cotter pin and axle hub nut.
  5. Remove the hub to knuckle bolts Hub and Knuckle Remove the hub bearing from the steering knuckle and axle shaft
  6. Remove the brake dust shield.
  7. Remove the axle shaft from the housing. Avoid damaging the axle shaft oil seal.
INSTALLATION
  1. Clean the axle shaft and apply a thin film of Mopar Wheel Bearing Grease to the shaft splines, seal contact surface, hub bore. Install the axle shaft into the housing and differential side gears. Avoid damaging the axle shaft oil seals in the differential.
  2. Install dust shield and hub bearing on knuckle.
  3. Install the hub bearing to knuckle bolts and tighten to 170 N·m (125 ft. lbs.) torque.
  4. Install the axle washer and nut, tighten nut to 237 N·m (175 ft. lbs.) torque. Align nut to next cotter pin hole and install new cotter pin.
  5. Install the brake components, Refer toBrakes.
  6. Install the wheel and tire assembly.
  7. Remove support and lower the vehicle. 8014d67b.gif

Feb 26, 2009 | 1996 Dodge Ram 1500 Club Cab

3 Answers

Remove front axle from differential on 2003 dodge ram


That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

Jan 06, 2009 | Dodge Ram 1500 Cars & Trucks

Not finding what you are looking for?
1994 Ford Ranger Supercab Logo

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...