Question about Mercury Villager

1 Answer

Where is the crank sensor for a Mercury Villager 97 located and how hard is it to replace? Do you have a diagrahm thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 135 Answers

FRONT OF ENGINE RIGHT BELOW DISTRIBUTOR

EASY REPLACEMENT

SHOULD HAVE THROWN A FAULT CODE THO

HOPE THIS HELPS

Posted on Aug 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location removal and installition of transmission speed sensor


Hi Anonymous, the link below is a youtube video showing how to replace a speed sensor on a 2000 mercury villager, I hope this motor and your motor are similar, Good luck and CHEERS..
How to replace speed sensor on 2000 Mercury Villager Nissan Quest

Apr 17, 2016 | 2002 Mercury Mountaineer

1 Answer

How to find the location of a crank sensor for 1998 mercury villager


The sensor is always located on the outside outside of the crankshaft on the body of the engine. you will see wire connection on the body. The sensor fits to the gears of the crackshaft and if not visble then you will have to remove surrounding fiitings to get to it. easier to see fron underneath the engine.

Aug 16, 2014 | Cars & Trucks

1 Answer

How do i put a crank sensor in 1999 mercury villager


http://groups.yahoo.com/group/villagerquest/

YOU DO NOT NEED A CRANK SENSOR. IT DOES NOTHING.

MAYBE NEED A CAM SENSOR IN DISTRIBUTOR. Not aviailable separately.

Rich Porter Reman is best bet. $200

gerry

Apr 06, 2011 | 1999 Mercury Villager

1 Answer

Installing distrubutor on a 97 Mercury villager


bring #1 cylinder up on Top Dead Center on compression stroke and line up marks on crank pulley. Rotor should point to #1 plug wire in cap.

go here for more help

http://groups.yahoo.com/group/villagerquest/

Apr 25, 2010 | 1997 Mercury Villager

2 Answers

Needing to find the location of a crank sensor for a 99 mercury villager


either behind or around crank pully or ontop of transmission

Mar 06, 2010 | 1999 Mercury Villager

2 Answers

1997 Mercury Villager car will turn over, but will not start. Used ether but nothing. Can't get spark. Installed another coil-- nothing. Installed electonic ignition module--nothing. Any ideas???


if you can get a scan tool, hook it up and check to see if you are getting engine RPM while cranking. if not than you may have faulty cranck sensor.

Nov 26, 2009 | Mercury Villager Cars & Trucks

1 Answer

Location of knock sensor on 97 mercury villager


it's in the valley of the engine. Do not ever replace it even if you get a code. A knock sensor will NEVER casue a driveabiity problem. It only retards timing 6 degrees if it senses spark knock. It also sets a code if an engine mount is broken and the engine rocks up and down on acceleration.

go here for help

http://groups.yahoo.com/group/villagerquest/

Oct 01, 2009 | 1997 Mercury Villager

1 Answer

Fuel temperature/sensor


go here for villager help http://autos.groups.yahoo.com/group/villagerquest/ SECTION 303-14: Electronic Engine Controls 1999 Villager Workshop Manual REMOVAL AND INSTALLATION ------------------------------------------------- It's in the fuel tank. WHy do you think you need to replace it? They seldom go bad. Fuel Temperature Sensor Removal Remove the fuel pump; refer to Section 310-01 . Remove the fuel temperature sensor. Disconnect the electrical connector. Disconnect and remove the fuel temperature sensor from the clip.

Jun 07, 2009 | 1999 Mercury Villager

1 Answer

Help!! I've got a 97 Villager (like the Nissan Quest) with window problems!!


when the widow is down, take some spraylube and spray into the tracks on either side of the window. see it that makes any difference

May 26, 2009 | 1997 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...