Question about 2007 Lexus LS 460 L Sedan

Open Question

How do you check power steering fluid level on 07 LS460

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
j_del
  • 1586 Answers

SOURCE: power steering audi a6 1999

First, I'd try refilling the fluid. You can't use fluid off the shelf - Audi uses proprietary power steering fluid, available at dealerships (probably a VW dealer can give you the same thing) or online at www.germanautoparts.com or www.ecstuning.com. Try refilling it. The power steering fluid is cooled by a cooler behind the lower part of the bumper, and the fluid itself cools the power steering pump. If you're low on fluid, the pump may be heating up and in turn, heating the fluid. Fill it to the proper level and keep an eye on it for a couple of days and see if that fixes the problem.

Posted on Jul 23, 2008

Ad
  • 2 Answers

SOURCE: 1995 bonneville power steering fluid

i don't know why they make it so hard to find, but this diagram i found helps a lot! i searched for a long time and finally saw this online, hope it helps! http://www.bonnevilleforum.com/t213271/

Posted on Dec 21, 2008

  • 94 Answers

SOURCE: power steering fluid on the ground. (1998 jetta gl)

you have a rack and pinion problem

Posted on Mar 09, 2009

c17hydro
  • 2984 Answers

SOURCE: Where is the Power steering Fluid located?

This is what it looks like:

b0cbdd2.jpg
THERE IS NO CAP TO FILL IT LIKE NORMAL POWER STEERING SYSTEMS. IT HAS TO BE SERVICED FROM THE INLET HOSE.

  1. Fill pump with hydraulic fluid through intake line. Turn the pulley/shaft by hand until fluid comes out of pressure port.
Look underneath the car up at the driver's side of the car above your tie rods (or look at it from above). It is mounted to your steering gear.

Posted on Jun 19, 2009

pugwash814
  • 377 Answers

SOURCE: power steering fluid level

most power steering caps have dipstick attached to the lid,and show a level for warm and cold, if not check the level is approx 1inc below neck...

Posted on Oct 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to add power steering fluid to 2008 pontiac g6


If you can't find a power steering fluid reservoir under the hood in the engine compartment your G6 could have Electronic Power Steering . If you look up under the dash below the steering column you will see a electric motor mounted to the steering column !
The power steering system reduces the amount of effort needed to steer the vehicle. The system uses the powertrain control module (PCM), body control module (BCM), power steering control module (PSCM), discrete battery voltage supply circuit, steering shaft torque sensor, steering wheel position sensor, power steering motor, driver information center (DIC), and the serial data circuit to perform the system functions. The PSCM and the power steering motor are serviced as an assembly and are serviced separately from the steering column assembly. The steering shaft torque sensor and the steering wheel position sensor are not serviced separately from each other or from the steering column assembly. The steering column assembly does not include the power steering motor and module assembly.

Jun 23, 2015 | 2008 Pontiac G6 Sedan

1 Answer

Bleed power steering on 2008 dodge avenger


to bleed power steering, with front wheels off ground slightly with front wheels pointing straight ahead.engine off. remove power steering filler cap.add power steering until fluid level stop dropping,wait couple minutes and wait, add fluid until level stay at full cold mark on power steering cap dip stick. dont over fill.when fluid level stop dropping, start vechicle,let it idle few minutes. see if fluid level drop if so add more fluid full cold mark.then turn steering all the way to left and right with out hitting a stop.turn steering wheel several times, then turn front wheels pointing forward check power steering fluid level.if power steering fluid level stop dropping air should be out of system, if steering turning wheel dont turn smoothly and power steering fluid look light tan color air getting in the system.check all power steering lines to rack and power steering pump for leaks.be sure you replaced all the power steering lines with new o rings if not you will get a leak.if you find a leak, you need to fix the leak and bleed system again.dont drive vechicle if your steering dont feel right,have vechicle towed to a garage.

Aug 25, 2012 | 2008 Dodge Avenger

1 Answer

How to change vane pump o/h kit


FIRST OF ALL TURN OFF RADIO REMOVE NEGATIVE BATTERY CABLE. THEN REMOVE POWER STEERING PUMP FLUID FROM POWER STEERING PUMP.USING A HAND PUMP SIPHON. BE CAREFUL DONT GET POWER STEERING FLUID ON CAR PAINT IT WILL DAMAGE PAINT JOB.PUT A DRAIN PAN UNDERNEATH CAR TO CATCH POWER STEERING FLUID THEN DISCONNECT POWER STEERING PUMP LINES.REMOVE POWER STEERING PUMP ADJUSTER BOLT AND MOUNTING BOLT.REMOVE POWER STEERING PUMP.MOST OF THE TIME NEW POWER STEERING PUMP DONT HAVE DRIVE PULLEY ON IT SO TAKE TO A MACHINE SHOP THE WILL REMOVE PULLEY FROM OLD PUMP AND PRESS ON THE PULLEY TO NEW POWER STEERING PUMP.BESURE TO BUY NEW O RINGS TO END OF PRESSURE LINE.ONCE NEW POWER STEERING PUMP HAS PULLEY IN PLACE AND YOU HAVE NEW O RING FOR HIGH PRESSURE LINE.INSTALL NEW PUMP.ADJUST BELT TENSION.NOW BLEED POWER STEERING PUMP WITH FRONT WHEELS POINT STRAIGHT A HEAD POSITION.POUR POWER STEERING FLUID IN PUMP UNTIL FLUID LEVEL ON COLD MARK ON POWER STEERING PUMP DIP STICK.KEEP ADDING FLUID UNTIL FLUID STOP DROPPING. START THE ENGINE LET IT RUN AT IDLE ADD MORE FLUID IF DROPS KEEP FLUID ON FULL COLD MARK.ON DIP STICK TURN OFF ENGINE.CHECK TO MAKE SURE POWER STEERING PUMP NOT LEAKING AT THE LINES THEN.SAFELY RAISE SUPPORT FRONT OF THE VECHICLE WITH JACK STANDS. MAKE SURE VECHICLE ON SOLID LEVEL GROUND CHECK.FLUID LEVEL MAKE SURE AT FULL COLD MARK. NOW START ENGINE.LET IDLE MINUTE.THEN TURN STEERING WHEEL ALL THE WAY TO THE LEFT TO RIGHT SEVERAL TIMES WITH OUT STOPPING IT IN PLACE. CHECK POWER STEERING FLUID WHEN FLUID LEVEL STOP DROPPING.AND FLUID IS NOT A TAN COLOR WHICH MEAN LOTS OF AIR IN SYSTEM. TURN OFF CAR UNTIL AIR BUBBLES DISAPPEAR.CHECK FLUID LEVEL BLEED POWER STEERING AGAIN. DONT DRIVE VECHICLE UNTIL STEERING FEEL NORMAL.IF FLUID REMAIN TAN WITH AIR BUBBLES CHECK FOR LEAKS AT POWER STEERING PUMP PRESSURE HOSE ORING. AND CHECK POWER STEERING LINES TO PUMP FOR LEAKS.

Mar 07, 2011 | 2000 Honda Civic

1 Answer

The power steering isn't working. The reservoir was empty and I added power steering fluid and it still very hard to steer


YOU HAVE A RUPTURE PRESSURE LINE IF YOU HAVE NO POWER STEERING FLUID IN THE POWER STEERING RESERVOIR.LOCATE LEAK THEN BLEED POWER STEERING SYSTEM BY ADDING POWER STEERING TO RESERVOIR.DONT OVER FILL BY FULL COLD MARK ON POWER STEERING DIP STICK.ADD FLUID TO RESERVOIR WAIT A 2 MINUTES.CHECK FLUID LEVEL AGAIN.WHEN POWER STEERING FLUID LEVEL STOP DROPPING.START ENGINE LET IT RUN FOR 10 SECONDS.THEN TURN OFF ENGINE CHECK POWER STEERING FLUID ADD FLUID IF FLUID LEVEL DROPS. WHEN FLUID LEVEL STOP DROPPING.SAFELY RAISE SUPPORT VECHICLE FRONT WHEELS.START ENGINE.NOW TURN STEERING WHEEL GENTLY FROM STOP TO STOP MEANING LEFT TO RIGHT DONT HOLD IN POSITION.LET THE STOP TO STOP BE QUICK.CHECK POWER STEERING FLUID AFTER YOU HAVE TURN STEERING WHEEL ABOUT 7 STOP TO STOP.WHEN FLUID LEVEL STOP DROPPING YOU AT HOT MARK ON DIP STICK BLEEDING PROCESS COMPLETE.TURN OFF ENGINE LOWER VECHICLE BACK TO GROUND WAIT ABOUT 5 MINUTES CHECK YOUR FLUID LEVEL.IF FLUID LOOKS LIKE A TAN COLOR.YOUR POWER STEERING SYSTEM FULL OF AIR.TURN OFF VECHICLE LET VECHICLE SET A LONG WHILE TO AIR BUBBLES SETTLE DOWN LOOK FOR LEAKS AROUND POWER STEERING PUMP FRONT SEAL AND CHECK FOR LEAKS AROUND POWER STEERING LINES.

Dec 01, 2010 | 1999 Oldsmobile Alero

1 Answer

Changeing a power steering pump


CHANGING POWER STEERING PUMP YOU HAVE TO PLACE A DRAIN PAN UNDER THE VECHICLE. SIPHON OUT POWER STEERING FLUID WITH A SIPHONER DONT USE YOUR MOUTH TO SIPHON SWALLOWING POWER STEERING FLUID CAN BE FATAL MAKE YOU SICK.WHEN ALL POWER STEERING FLUID IS REMOVED FROM POWER STEERING PUMP.REMOVE DRIVE BELT.THEN REMOVE THE POWER STEERING PUMP.THEN YOU HAVE TO REMOVE THE POWER STEERING PUMP PULLEY THE NEW POWER STEERING PUMP DONT HAVE A PULLEY YOU HAVE TO HAVE REMOVE PULLEY FROM THE OLD POWER STEERING PUMP.YOU NEED A PUMP PULLEY REMOVER AND A PULLEY INSTALLER.YOU CAN TAKE OLD POWER STEERING PUMP AND NEW POWER STEERING PUMP TO A MACHINE SHOP.THEY WILL REMOVE PULLEY OFF OLD PUMP PRESS IT ON NEW POWER STEERING PUMP.THAT WOULD BE CHEAPER THAN BUYING THE PULLER AND INSTALLER.GO TO AUTO PARTS STORE BUY NEW HIGH PRESSURE LINE O RING GOES TO PRESSURE LINE GOING INTO POWER STEERING PUMP.ONCE YOU GET NEW PUMP READY PULLEY BEEN PRESSED ON.TAKE POWER STEERING PUMP HOME PUT IT ON. BLEED POWER STEERING SYSTEM.WHAT YOU DO WHEN YOU GET NEW PUMP INSTALLED HIGH PRESSURE LINE IN PLACE.PUMP BOLTED IN DRIVE BELT ON POUR POWER STEERING FLUID IN POWER STEERING PUMP UNTIL FLUID LEVEL STOP DROPPING AND YOUR LEVEL ON POWER STEERING DIP STICK AT COLD LEVEL.NOW START CAR UP LET IT IDLE FOR 3 MINUTES.THEN TURN OFF ENGINE CHECK POWER STEERING FLUID IF FLUID LEVEL DROP ADD LITTLE MORE UNTIL LEVEL ON DIP STICK ON COLD MARK DONT OVER FILL.NOW SAFELY RAISE SUPPORT FRONT OF VECHICLE. START THE ENGINE.TURN STEERING WHEEL FROM ALL THE WAY FROM LEFT TO RIGHT DONT STOP LOCK WHEEL .GO LEFT TO RIGHT SEVERAL TIMES.THEN TURN OFF ENGINE CHECK FLUID LEVEL.IF ALL IS GOOD LET VECHICLE BACK DOWN LET IT SIT FOR A WHILE CHECK FLUID AGAIN.DONT DRIVE VECHICLE IF POWER STEERING PUMP MAKE NOISES OR YOUR STEERING FEEL STIFF HARD TO TURN.JUST MAKE SURE FLUID LEVEL RIGHT AND DRIVE BELT TIGHT GOOD LUCK.

Nov 02, 2010 | 1999 Oldsmobile Alero

1 Answer

WeMy power steering fluid was leaking I tool it to the shop they told me It was the pump so I brought a new pump and got It put in and now I still cant turn my steering wheel


HEY DO THIS,YOU NEED TO BLEED SYSTEM. TO BLEED POWER STEERING SYSTEM.TO DO THIS.FILL THE POWER STEERING RESERVOIR TO COLD FULL MARK ON DIP STICK.WAIT A FEW MINITES,FLUID LEVEL DROP ADD MORE FLUID UNTIL REACH COLD MARK ON THE DIP STICK..WAIT FEW MINUTES.START ENGINE LET IT RUN FOR 2 OR 3 SECONDS.TURN OFF ENGINE CHECK POWER STEERING FLUID ADD MORE FLUID.DO THIS UNTIL FLUID LEVEL STOP DROPPING.WHEN FLUID LEVEL STOP DROPPING.SAFELY RAISE FRONT OF THE VECHICLE UNTIL FRONT WHEELS DONT TOUCH THE GROUND.START ENGINE UP.TURN THE STEERING WHEEL GENTLY FROM STOP TO STOP,CHECK THE RESERVOIR FLUID LEVEL LOOKS GOOD TURN OFF ENGINE LOWER VECHICLE .LOWER VECHICLE TO GROUND. LET VECHICLE SET FOR 2 MINUTES CHECK POWER STEERING FLUID LEVEL.IF STILL LOW ADD LITTLE MORE.TO THE COLD FULL MARK ON DIP STICK. DONT OVER FILL BECAUSE FLUID LEVEL RISES WHEN IT GET HOT.WHEN DONE IF STEERING WHEEL STILL FEEL HARD TO TURN YOU SEE AIR BUBBLES IN FLUID THATS WHEN FLUID HAS A TAN LOOKING COLOR WAIT 5 MINUTES AND.REPEAT THE BLEEDING PROCESS. DONT DRIVE OR OPERATE VECHICLE ON HIGHWAY UNTIL POWER STEERING HAS NORMAL OPERATION.

Sep 26, 2010 | 1999 Oldsmobile Alero

1 Answer

Get noise like power steering fluid is gone from transmission in gear only


first of all power steering uses power steering fluid and the transmission uses transmission fluid, check both the power steering fluid level and the transmission fluid level and fill to proper levels with proper fluid

Jul 05, 2010 | 2003 Lincoln Navigator

1 Answer

Cannot get my power steering pump that I replaced to stop foaming. I cannot get the air out of the system


CHECK POWER STEERING FLUID LEVEL.SOUND LIKE ITS VERY LOW CAUSING CAUSING MORE AIR SYSTEM.WHICH WILL CAUSE FOAMING.LET VECHICLE SET UNTIL AIRATED FLUID SETTLE DOWN.TURN STEERING TO THE LEFT.CHECK POWER STEERING FLUID LEVEL.ADD FLUID TO COLD MARK LEVEL ON DIP STICK.CRANK UP VECHICLE.TURN STEERING WHEEL LEFT TO RIGHT WITH OUT STOPPING SEVERAL TIMES.THEN CHECK POWER STEERING FLUID.DOING THIS BLEEDS AIR OUT OF THE POWER STEERING SYSTEM.

Jun 19, 2010 | Cars & Trucks

1 Answer

Can low steering fluid cause mechanical problems


Problems associated with low power steering fluid…

Hard Vehicle Steering
A low power steering fluid level can often times cause a vehicle's steering to become hard and labored. Adequate amounts of power steering fluid are necessary to enable a vehicle's power steering system to function and operate at optimum levels. A lack of power steering fluid in a vehicle's power steering system reduces the amount of hydraulic fluid pressure necessary to efficiently operating the various parts of the entire power steering system. Power steering fluid supplies the fluid force needed to operate the power steering gears and to enable power steering gearbox operation. Low power steering fluid levels reduce this hydraulic pressure, which commonly results in hard vehicle steering.

Pump Noise
It is very common for a low power steering fluid level to cause significant power steering pump noise. An adequate amount of power steering fluid is required to ensure the proper function and longevity of a power steering pump unit, which is a belt-driven pump responsible for housing and circulating power steering pump fluid. A low level of power steering fluid results in increased power steering pump friction, heat, and wear, all of which can significantly reduce the operational life of the power steering pump while at the same time cause excessive power steering pump noise.

Fluid Boiling
Many times a low power steering fluid level can result in excessive heating of power steering fluid, a condition that can seriously degrade the fluid and cause it to boil. A low power steering fluid level results in less available fluid to both lubricate and cool a power steering pump unit. A lack of power steering pump lubrication and cooling leads to excessive heat being generated within the power steering pump unit itself, a condition that translates into the available level of power steering fluid becoming super-heated and degraded. When this happens it is common for the power steering fluid to boil and lose all of its lubricating and heat-reducing capabilities.

Gearbox Wear
The power steering gearbox is a set of gears within a vehicle's power steering system designed to facilitate movement of a vehicle's front wheels. The power steering gearbox is connected to the power steering pump by hydraulic fluid lines that deliver a constant supply of power steering fluid to the power steering gearbox. A low power steering fluid level, especially a chronic and severe low power steering fluid level, can lead to increased friction and wear within the power steering gearbox assembly, a condition that can significantly shorten the operational life of the power steering gearbox and negatively affect its operation

Nov 26, 2009 | 2003 Pontiac Grand Am

Not finding what you are looking for?
2007 Lexus LS 460 L Sedan Logo

Related Topics:

341 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

918 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...