Question about 2004 Nissan Maxima

Open Question

Replacing a o2 sensor in a nissan maxima 2004 need a guide

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Check Engine Light 1996 Nissan Maxima

There is a silver box underneath the center console, just to the right of the gas pedal.

Pull off the plastic cover (it has two plastic fasteners. It will go back on).

Peel back the plastic film covering the screw.

Put the key in and turn the ignition switch on, but do not strt the car (all the warning indicator lights should go on).

Turn the screw all the way clockwise for two or three seconds and turn turn it back. Repeat just to be sure.

Turn the key off. When you turn the key back on the Check Engine light should be off.

Replace the plastic film over the screw and replace the plastic panel.

Posted on Oct 18, 2008

Ad
johnny5846
  • 379 Answers

SOURCE: location of a o2 sensor 2001 nissan maxima

bank 1 refers to the side of the engine that #1 cylinder is on , and sensor 2 refers to downstream , after the catalytic converter. , this link shows bank 1 on a 2001 nissan maxima V6 being on the firewall side . if you had a 4 cylinder it would be downstream after the catalytic converter .

http://www.autozone.com/N,26200242/shopping/specsSelect.htm



Posted on Jan 04, 2009

  • 2 Answers

SOURCE: Starter motor and ignition switch and O2 sensor and pipe 1997 Nissan Maxima

You need to remove all of the air intake and other things behind the battery. The start motor is held in with two bolts. You might need a breaker bar to break loose the one bold as I did. Once you remove all of the air intake equipment. This will help you gain access to the starter motor. You might not need to remove all the air intake equipment I know it made it alot easier for me to remove the starter and I took it to the auto store and had it tested.

Posted on Apr 07, 2009

SOURCE: WHERE IS THE CAM POSITION SENSOR LOCATED ON A 2004 NISSAN MAXIMA

WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....



Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...



you all enjoy your rides out htere!!!

Posted on Jul 01, 2009

  • 145 Answers

SOURCE: where is the cam position sensor located on a 2004

Here is 7353049.jpg

Posted on Jul 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know how many O2 wires in Nissan Maxima 03 sE


They have four wires, two for the signal and two for the heater circuit.

Sep 21, 2016 | 2003 Nissan Maxima

1 Answer

Where would the af sensor be located on my 2004 nissan maxima


your maxima has 2 a/f ratio sensors. they are both screwed into the exhaust manifolds. bank 2 which is the front bank by radiator has sensor clearly visible right by the fans. bank 1 is a pain in the rear to replace, because of its location by the firewall. you will need to perform "self learn reset" procedure after replacing the a/f ratio sensor, or the code will come back on, even tho you don't have an issue with the sensor. reset procedure gets done with nissans consult scanner.

Jul 26, 2016 | 2004 Nissan Maxima

1 Answer

How many O2 censors in a 98 Maxima


In cars with EFI control there is a heated oxygen sensor(HO2S) before the cat converter and a ordinary oxygen sensor (O2S) after the cat convertor. so that means 1 of each on a 4 cylinder engine and 2 of each on a "V" engine . They are not interchangeable so a O2 sensor will not replace a HO2S sensor

Sep 04, 2014 | 1998 Nissan Maxima

1 Answer

Engine light is on, on a1998 nissan maxima


go to local Autozone or similiar parts seller... they will check it for free and give you a printout of what's needed...
probably just an O2 sensor on the 98 nissan, but I would replace catalytic converter if near 200k miles for GP.

Mar 17, 2013 | 1998 Nissan Maxima

1 Answer

I have a 05 nissan altima with the code p0037 and p0037 pd. what do the mean and how can i fix it?


Bad o2 sensor heater circuit. Check for damaged wiring to sensor first, if undamaged replace sensor.

Mar 06, 2011 | 2004 Nissan Maxima

3 Answers

I failed the emisson's test. I have a 97 Nissan


P0136 indicates a bad O2 sensor. This reports poor emission performance back to the car's PCM (computer)
P0325 indicates a bad "Knock" sensor which would adversely effect drivability as far as performance is concerned. Only way to fix these 2 problems is replacement of the 2 components.

Nov 03, 2009 | 1997 Nissan Maxima

1 Answer

2001 Nissan Maxima service engine light stays on code from Auto Zone scanner is PO139 and PO138. What should my next step be to solve this problem.


code p 0138 refers to 2 items
1--heated oxygen sensor(HO2S) 2 bank 1--high voltage ==causes --wiring short to positive --HO2S---ECM
2--oxygen sensor (O2S) 2 bank 1--high voltage ===causes wiring short to positive ---ECM
code p 0139 refers to 2 items
1--- heated oxygen sensor (HO2S) 2 bank 1--slow response ===causes --heating inoperative --wiring--ECM
2--oxygen sensor (o2S) 2 bank 1 slow response ===causes --wiring --- O2S

heated oxygen sensors9HO2S) are in the exhaust manifold before the cat converter
Oxygen sensors (O2S) are after the cat converter
it is indicated that the HO2S is faulty-
check the wiring and /or replace both sensors

Nov 16, 2017 | 2001 Nissan Maxima

2 Answers

Location of a o2 sensor 2001 nissan maxima


bank 1 refers to the side of the engine that #1 cylinder is on , and sensor 2 refers to downstream , after the catalytic converter. , this link shows bank 1 on a 2001 nissan maxima V6 being on the firewall side . if you had a 4 cylinder it would be downstream after the catalytic converter .

http://www.autozone.com/N,26200242/shopping/specsSelect.htm



Jan 04, 2009 | 2001 Nissan Maxima

Not finding what you are looking for?
2004 Nissan Maxima Logo

Related Topics:

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...