Question about Ford Explorer

Open Question

How to fix code # PO463 on ford explorer 2005?

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ZJLimited
  • 17970 Answers

SOURCE: how to fix po106 code

Fault code P0106 its a warning about MAP/Barometric Pressure Circuit Range/Performance Problem

The Powertrain Control Module (PCM) uses the Manifold Absolute Pressure Sensor (MAP) to monitor engine load. (NOTE: Some vehicles have a Barometric Pressure (BARO) sensor that is integral to the Mass Air Flow (MAF) sensor and do not have a MAP sensor. Other vehicles have a MAF/BARO and a redundant MAP sensor where the MAP sensor functions as a backup input in case of MAF failure.) The PCM supplies a 5 Volt reference signal to the MAP sensor. Usually the PCM also supplies a ground circuit to the MAP sensor as well. As the manifold pressure changes with load, the MAP sensor input informs the PCM. At idle the voltage should be 1 to 1.5 Volts and approximately 4.5 Volts at Wide Open Throttle (WOT). The PCM looks for any change in manifold pressure to be preceded by a change in engine load in the form of changes in throttle angle, engine speed, or Exhaust Gas Recirculation (EGR) flow. If the PCM doesn't see any of these factors change while detecting a rapid change in MAP value, it will set a P0106.

The following could be symptomatic of a P0106:
Engine runs rough
Black smoke at tailpipe
Engine will not idle
Poor fuel economy
Engine misses at speed


A P0106 could be caused by:
Bad MAP sensor
Water/dirt intrusion affecting MAP sensor connector
Intermittent open in the reference, ground, or signal wire for the MAP sensor
Intermittent short in the reference, ground, or signal wire for the MAP sensor
Ground problem due to corrosion causing intermittent signal problem
A break in the flexible air intake duct between the MAF and the intake manifold
Bad PCM (do not assume the PCM is bad until you've exhausted all other possibilities)

Check this oossible solutions:
Using a scan tool, watch the MAP sensor value with the key on, engine off. Compare the BARO reading with the MAP reading. They should be roughly equal. The voltage for the MAP sensor should read approx. 4.5 volts. Now start the engine and look for a significant drop in the MAP sensor voltage indicating the MAP sensor is working.

If the MAP reading doesn't change perform the following:
* With the Key on, engine off, disconnect the vacuum hose from the MAP sensor. Using a vacuum pump, pull 20 in. of vacuum on the MAP sensor. Does the voltage drop? It should. If it doesn't inspect the MAP sensor vacuum port and vacuum hose to manifold for a restriction of some kind. Repair or replace as necessary.
* If there are no restrictions, and the value doesn't change with vacuum, then perform the following: with the Key on and engine off and the MAP sensor unplugged, check for 5 Volts at the reference wire to the MAP sensor connector with a Digital Voltmeter. If there is none, check for reference voltage at the PCM connector. If the reference voltage is present at the PCM connector but not the MAP connector, check for open or short in the reference wire between MAP and PCM and retest.
* If reference voltage is present, then check for existing ground at the MAP sensor connector. If it isn't present then repair open/short in the ground circuit.
* If ground is present, then replace MAP sensor.

Other MAP sensor trouble codes include P0105, P0107, P0108 and P0109.

Hope this helps.

Posted on Jul 26, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The 2005 ford freestyle has two sensors in the gas tank, Witch one would i change if i got a po463 high input.


code p 0463 refers to fuel tank level sensor --high input ===causes --wiring short to positive --fuel tank level sensor ---ECM
remove a wire from each at a time to isolate the sensor in question
check the wires for a short to the sensor or in a connection ( water etc)

Sep 30, 2016 | 2005 Ford Freestyle

1 Answer

How to fix my headlights


Search Results

    Explorer Headlight Problem and Interior Stuff - YouTube

    ? 10:53
    https://www.youtube.com/watch?v=f1j-H1dGT4o
    Jan 1, 2011 - Uploaded by justhes
    Explorer Headlight Problem and Interior Stuff ... Thank's to your movie I fix my car. .... 2001 Ford F150 Headlight Switch Replacement - Duration: 5:05. Jon Olson 10,273 views. 5:05. 2003 Ford F-150 4X4 Repair Part #3 The GEM Module ... EXCLUSIVE: 2016 Ford Explorer Sport with Mark Mills at Athens ...

    Replace 2001-2005 Ford Explorer Headlight / Bulb, How to ...

    ? 4:49
    https://www.youtube.com/watch?v=cQJrO0L_tSM
    Sep 16, 2013 - Uploaded by Go-Parts
    Replace 2001-2005 Ford Explorer Headlight / Bulb, How to Change Install ... How To Install Replace Headlight Ford Explorer Sport Trac 01-05 ...

    How To Install Replace Headlight Ford Explorer Sport Trac ...

    ? 4:28
    https://www.youtube.com/watch?v=NzMVcCsZ860
    May 11, 2010 - Uploaded by 1A Auto Parts
    How To Install Replace Headlight Ford Explorer Sport Trac 01-05 1AAuto.com .... I did this on my wifes 2003 Explorer only difference was the screw was a ... Replace 2001-2005 Ford Explorer Headlight / Bulb, How to Change ...

    2001 Ford F150 Headlight Switch Replacement - YouTube

    ? 5:05
    https://www.youtube.com/watch?v=l84h2PUHS0E
    Mar 1, 2014 - Uploaded by Jon Olson
    Headlamp Switch was purchased through Auto Parts Warehouse: ... to help me with my 2001 Ford Explorer Sport-HeadlightSwitch, but the .... Ford F150 Explorer 2000 2001 2002 Overhead Console Repair - Duration: 6:38.




Jan 10, 2016 | 2001 Ford Explorer Sport

1 Answer

Ford explorer 2005 radio key code?


take your title to a ford dealer and they will supply the code.

Nov 18, 2014 | 2005 Ford Explorer

1 Answer

Code po463 fuel level sensor circuit high input


Most likely a faulty fuel level sender , mounted on the fuel pump module in the fuel tank. Recommend replace complete assembly.

Dec 24, 2013 | 2005 Dodge Dakota Quad

1 Answer

2005 ford explorer door lock relay


I have 2005 ford explore and i have try u can lock in from inside but when u try to unlock it with the remote i have reset it and it would work for a little while then nothings i dont know where to look can anyone help

Feb 17, 2013 | 2005 Ford Explorer

1 Answer

My 2005 Ford Explorer won't start. Doesn't turn over. Have new battery. All lights come on. Any answers?


are you using the coded key or one made at your local key maker? if you are using the proper key, then it might be your starter. sometimes a simple tap on the starter will fix this, but waking it up and freeing it up if it is "frozen up".

Oct 17, 2009 | 2005 Ford Explorer

1 Answer

P0171 and p0463


Replace the fuel pump module (inside the fuel tank) it has 2 level sensors on it. The po463 code is an open condition on the high level sensor, one sensor reports to the ECM, other to your gas gauge on the dash.

Mar 14, 2009 | 1999 Chevrolet Malibu

1 Answer

2005 Ford Explorer XLT


transmission need to fix

Sep 14, 2008 | 2005 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...