Question about 2000 Lincoln Town Car

Open Question

How do I remove the dash board panel in a 2000 Lincoln Town Car

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fastboyz
  • 674 Answers

SOURCE: 2000 lincoln ls heater not working...thermostat?

no this manual wont work your LS is based on a Jaguar .
do you have the v6 or v8?

Posted on Nov 18, 2008

Ad
  • 1 Answer

SOURCE: 1997 Town Car - How do you remove the complete dash board panel?

There are 3 small bolts across the top where the front defrost grill is. 2 large bolts directly under the headlight switch and another big bolt lower right hand corner of the glovebox area.

Posted on Feb 19, 2009

  • 333 Answers

SOURCE: Heater core - 1996 Lincoln Town Car

  1. Disconnect the negative battery cable.
  2. Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.
  3. Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.
  4. Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
  5. Remove the right and left lower instrument panel insulators.
  6. On 1990-00 vehicles:
    1. Remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator.
    2. Disconnect the ATC sensor tube from the evaporator case connector.
  7. Disconnect the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.
  8. Remove the 2 hush panels.
  9. Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum. Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
  10. Remove the 2 nuts from the 2 studs along the lower flange of the plenum.
  11. Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
  12. Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly. Pull the heater core and seal assembly from the plenum assembly.
To install:
  1. Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
  2. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  3. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  4. Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
  5. Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
  6. Connect the white vacuum hose to the outside-recirculating door vacuum motor. Connect the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
  7. If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
  8. If equipped with ATC, proceed as follows:
  9. Connect the temperature control cable to the ATC sensor and adjust the cable. Route and connect the vacuum harness connector to the ATC sensor and connect the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
  10. On 1990-00vehicles:
    1. Connect the ATC sensor tube to the evaporator case connector.
    2. Install the cross body brace and connect the wiring harness to the blend door actuator.
    3. Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
  11. Connect the vacuum supply hose(s) to the vacuum source.
  12. Install the right and left lower instrument panel insulators and install the 2 hush panels.
  13. Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
  14. Connect the negative battery cable and check the system for proper operation. I hope this helps. Don,t forget to rate my answer.

Posted on Mar 01, 2009

old marine
  • 2005 Answers

SOURCE: need routing diagram for 2000 lincoln town car serpentine belt

There's a diagram at this link.

Posted on May 11, 2009

kennyz195
  • 61 Answers

SOURCE: 2003 Lincoln Town Car - Power window switch removal/installation

SECTION 501-05: Interior Trim and Ornamentation 2003 Town Car Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/28/2002 Front Door Trim Panel adobe.gif Printable View (206 KB) Removal and Installation
NOTE: LH side shown, RH side similar.

  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01.
  1. Remove the window switch plate.
    a0045307.gif
  1. Disconnect the electrical connectors.
    a0044981.gif
  1. ani_caut.gif CAUTION: Use care not to damage the trim panel covers.
    Open the screw covers.
    a0045817.gif
  1. Remove the screws and the assist handle.
    a0045818.gif
  1. Remove screws and the front door trim.
    a0045819.gif
  1. Disconnect the electrical connectors.
    a0045834.gif
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n306887&c35=wsm%2cfront%20door%20trim%20panel%2cs3g%2c501-05%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=modem&hp=n&[aqe]

Posted on Apr 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My instruments cluster panel and lights don't work on my 2006 lincoln town car..what could it be?if its the fuse where can I locate it.


Lincoln Town Car Electrical Problems - Car Forums at Edmunds.com

forums.edmunds.com > Lincoln > Lincoln Town Car

Jun 24, 2012 - 30 posts - ‎20 authors
Learn more about Lincoln Town Car at the Edmunds.com Car ... the radio shut off, then the instrument panel, but car kept running. ... Also I don't know if you can facebook me, because that's how I ... in interior lights and instruments (recently on myson-in-law's Taurus) .... All lights work.....all fuses are fine. Caravan/Town & Country Electrical Problems - Car ...
30 posts
Dec 2, 2011
Jeep Liberty Electrical and Lighting Problems - Car ...
30 posts
Jul 19, 2011
Ford Expedition Electrical Problems - Car Forums at ...
30 posts
Mar 13, 2008
More results from forums.edmunds.com

Lincoln town car dash light issue - YouTube

? 0:43
https://www.youtube.com/watch?v=1GZMDC2uu58
Sep 18, 2014 - Uploaded by john brewer
Lincoln town car dash light issue ... My 04 town car dash flickers on & off. ... How To Replace A Ford/Lincoln ...

LS Electrical Problems - Crazy Instrument Panel ... - Car



Dec 16, 2015 | Lincoln Cars & Trucks

1 Answer

How to remove and replace heater core on a 1996 lincoln town car, signature series


Hate to tell you this, but you will need to remove the entire dashboard to access the heater core.

Jan 03, 2015 | 1996 Lincoln Town Car

1 Answer

How do you change the light bulb for the gear shift on 1997 lincoln town car cartier


you have to take out nearly everything on the dash to get behind there. odds are its a diode and the board may need to be replaced.

Jul 27, 2014 | 1997 Lincoln Town Car

1 Answer

Heater core replacement in a 2000 lincoln town car


remove the whole dash to get the heater unit out ,sorry no short cuts available

Jan 28, 2012 | 2000 Lincoln Town Car

1 Answer

Hi i have 2000 lincoln town car.could u please let me know is there any other lightng cntrol module number that I could use instead of XW1T-13C788-AB. for a 2000 Lincoln Town Car? thank you


this is an engineering part number off the part. not the service number.
the service numbers you can use are yw1z-13c788-BA or YW1Z-13C788-AA, or XW1Z-13C788-AA.

However, Gino on ebay fixes these for $175. Go to ebay and type in the serach box LCM Lincoln town car, and you should find him. He is is California.

Good luck.

It's under the dash above the steering column. remove sound cover for access.

Jul 29, 2011 | 1999 Lincoln Town Car

1 Answer

2000 lincoln town car Clicking Noise Coming From Under The dash board sound like when you have your signal lights on but it is faster. use to go away when the car heats up. it is coming from the place...


This clicking is the Antilock brake system doing a self test. It's mentioned in the owners manual. Nothing to worry about but it should only take a minute and its best to let it fully cycle. Ned

Aug 27, 2009 | 2000 Lincoln Town Car

1 Answer

1991 lincoln Continental Dash Board completely out


check ignition fuse and fuse link.if all is good.looks like ignition switch is bad.

Jun 02, 2009 | 1991 Lincoln Town Car

1 Answer

Led radio station indicator light out on a lincoln town car


Most likely not. In order to replace the bulb you will have to remove it from the dash.

Mar 11, 2009 | 2000 Lincoln Town Car

2 Answers

1997 Town Car - How do you remove the complete dash board panel?


There are 3 small bolts across the top where the front defrost grill is. 2 large bolts directly under the headlight switch and another big bolt lower right hand corner of the glovebox area.

Feb 09, 2009 | 1997 Lincoln Town Car

1 Answer

1989 Lincoln Town Car Heater core


Go to Autozone and purchase a Clymer repair manuel. It will show how to remove the dash. You need to find all the screws.

Nov 05, 2008 | 1989 Lincoln Town Car

Not finding what you are looking for?
2000 Lincoln Town Car Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...