Question about 1994 Ford Taurus

1 Answer

How do you get brake fluid to go through the lines there are front brakes

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 225 Answers

There is a little bleeder nut on the back of the brake caliper. You will have to take the tire off and get your head under there to see it, but loosen the nut a turn or 2 and have some one pump the brake pedal all the way to the floor until fluid comes out. Do this until a smooth stream shoots out and have the person hold the brakes to the floor and tighten the bleeder nut. Do the same for every brake that you replaced.

Posted on Aug 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 95 Diamante and the front right brake froze. We can't get brake fluid to the caliber.


its possible that the rubber flexible line is blocked inside. you may have to replace it.

May 12, 2017 | Cars & Trucks

2 Answers

No brake fluid out of master cylinder to one front brake caliper


one of the pistons in the brake master cylinder is poss stuck at the bottom of its stroke or the return spring has broken, dont take any chances with brakes change that master cylinder

Apr 17, 2017 | 1993 Jaguar XJ6

1 Answer

Golf not braking on rear brakes also no pedal


You say you filled it with fluid after the repairs. You must also "bleed" the brake lines to purge any air that is trapped in them. Brake fluid provides the hydraulic compression that causes the brake pads to clamp to the brake rotor/drum. Air in the lines will prevent this as when the brake pedal is pressed, the fluid will simply pressurize the air in the lines and not activate the caliper/wheel cylinder. The reason you have front brakes is that modern vehicles have dual-reservoir master cylinders to prevent total brake loss in the event of a leak. This is why you still have front brakes as there is no air in those lines. You will need to bleed the rear brake lines at BOTH rear wheels to purge air rom the system. The procedure is fairly simple, though some cars with ABS have to have things done differently. I would recommend you check an online forum for you vehicle (simply Google "bleed rear brakes 20xx VW Golf) and see what comes up. It is easier to do with two people, but one can sometimes pull it off.

Jan 01, 2012 | Volkswagen F 224 Cars & Trucks

1 Answer

Replaced all brake lines, rear wheel cylinders, front calipers. No fluid to rear brakes, no fluid to master cylinder bleeder. Fluid is in front brakes. How to resolve? Thank you


It sounds as though where the rear brake lines meet up with the master cylinder; there is probably a piece of dirt in the lines that could be blocking any fluid from getting in. To test this, I would remove the brake lines from the master cylinder and then remove the master cylinder. Once done, have the master cylinder cleaned inside out. This will remove the dirt particles that are clogging your lines.

Aug 22, 2011 | 1988 GMC C2500

1 Answer

I replaced my front brake router and brake pads today. when i bleed the front left brake, a line which im assuming is a brake line near the rear left tire burst and is leaking brake fluid. when u tried...


First, there is NO Pumping of the brake pedal
involved in bleeding brakes

I think your smart enough to know you
need to replace both rear brake hoses,
before you proceed with the bleeding

Mar 22, 2011 | 1997 Chevrolet Cavalier

1 Answer

2005 GMC Envoy, no brake fluid is getting to the right front caliper. disconnected the brake line where the rubber line and the metal line are attached, pumped brakes and get absolutely no fluid through...


You may have a defective line on the right front brake. GM had a batch of bad lines installed on several year models. I had one collapse on mine with the caliper closed and burned my caliper, rotor and pads. Try to disconnect the metal line further back at the equalizer and see if you get fluid there. If you do replace line.

Mar 11, 2011 | 2005 GMC Envoy

1 Answer

How to bleed brakes on 1997 Saturn


The brake system bleeding procedure differs for ABS and non-ABS vehicles. The following procedure pertains only to non-ABS vehicles. For details on bleeding ABS equipped vehicles, refer to the ABS procedures later in this section.

WARNING Make sure the master cylinder contains clean DOT 3 brake fluid at all times during the procedure.
  1. The master cylinder must be bled first if it is suspected of containing air. Bleed the master cylinder as follows:
    1. Position a container under the master cylinder to catch the brake fluid.
    2. Loosen the left front brake line (front upper port) at the master cylinder and allow the fluid to flow from the front port.
    3. Connect the line and tighten to 24 ft. lbs. (32 Nm).
    4. Have an assistant depress the brake pedal slowly one time and hold it down, while you loosen the front line to expel air from the master cylinder. Tighten the line, then release the brake pedal. Repeat until all air is removed from the master cylinder.
    5. Tighten the brake line to 24 ft. lbs. (32 Nm) when finished.
    6. Repeat these steps for the right front brake line (rear upper port) at the master cylinder.
WARNING Do not allow brake fluid to spill on or come in contact with the vehicle' finish, as it will remove the paint. In case of a spill, immediately flush the area with water.
  1. If a single line or fitting was the only hydraulic line disconnected, then only the caliper(s) or wheel cylinder(s) affected by that line must be bled. If the master cylinder required bleeding, then all calipers and wheel cylinders must be bled in the proper sequence:
    1. Right rear
    2. Left front
    3. Left rear
    4. Right front
  2. Bleed the individual calipers or wheel cylinders as follows:
    1. Place a suitable wrench over the bleeder screw and attach a clear plastic hose over the screw end.
    2. Submerge the other end in a transparent container of brake fluid.
    3. Loosen the bleed screw, then have an assistant apply the brake pedal slowly and hold it down. Close the bleed screw, then release the brake pedal. Repeat the sequence until all air is expelled from the caliper or cylinder.
    4. When finished, tighten the bleed screw to 97 inch lbs. (11 Nm) for the front, or 66 inch lbs. (7.5 Nm) for the rear.
  3. Check the pedal for a hard feeling with the engine not running. If the pedal is soft, repeat the bleeding procedure until a firm pedal is obtained.
zjlimited_349.jpg

Fig. 1: Loosen the front brake line in order to bleed the master cylinder

zjlimited_350.jpg

Fig. 2: Connect a bleed hose from the bleed valve on the front caliper to a jar of brake fluid

zjlimited_351.jpg

Fig. 3: Always follow the lettered sequence when bleeding the hydraulic brake system





Hope this helps to solve it; remember to rate this answer.

Dec 29, 2010 | 1997 Saturn SL

1 Answer

How do you get the capierer pin off to put front brake pads on my Mercury Sable LS?


Section 06-03: Brakes, Front Disc 1999 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478) . Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120) , front disc brake rotor shield (2K004) or front wheel knuckle (3K185) .
  1. Remove rear brake pin retainers (2N386).
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125) . Do not pry directly against metal caliper piston or damage will occur.
  1. NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .

    Position disc brake caliper out of the way.
  1. Remove inner outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate .
  1. Inspect both rotor braking surfaces. Minor scoring or buildup of lining material does not require machining or replacement of front disc brake rotor.
-----------------------------------------------------------------
remove the 2 pins, #10 in pic. Usually has a dust cover over pin accessopening. Usually torx haed or hex head bolts (pins).


snorkelbobby_7.gif

Nov 12, 2010 | 1999 Mercury Sable

1 Answer

How to bleed brakes on 2002 toyota sienna


Here is the procedure from the service manual. I would add just one thing. Do each wheel in this order

  1. right rear wheel
  2. left rear wheel
  3. right front wheel
  4. left front wheel
BLEEDING

HINT: If any work is done on the brake system or if air in the brake lines is suspected, bleed the air from the system.

NOTICE: Do not let brake fluid remain on a painted surface. Wash it off immediately.


a)FILL BRAKE RESERVOIR WITH BRAKE FLUID Fluid:SAE J1703 or FMVSS No. 116 DOT3

b)BLEED MASTER CYLINDER HINT: If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

c)Disconnect the brake lines from the master cylinder. SST 09023-00100 Slowly depress the brake pedal and hold it.

Block off the outlet plug with your finger and release the brake pedal.
Repeat (b) and (c) 3 or 4 times.


BLEED BRAKE LINE

1. Connect the vinyl tube to the caliper or wheel cylinder bleeder plug.
2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down.
3. At the point when fluid stops coming out, tighten the bleeder plug, then release the brake pedal. Torque: (Bleeder plug) Front brake caliper
: 8.3 Nm (85 kgf-cm, 74 inch lbs.) Rear wheel cylinder: 8.5 Nm (87 kgf-cm, 75 inch lbs.)
4. Repeat (b) and (c) until all the air in the fluid has been bled out.
5. Repeat the above procedure to bleed the air out of the brake line for each wheel.

CHECK FLUID LEVEL IN RESERVOIR Check the fluid level and add fluid if necessary. Fluid: SAE J1703 or FMVSS No. 116 DOT3

Jun 25, 2010 | 2002 Toyota Sienna

1 Answer

Unable to bleed front brakes


loosen the front brake line that goes to the master cylinder fill master cylinder up with fluid and bleed it first by attaching a flexible line from master cylinder front brake side submerge that line into jar of brakefluid keeping air from entering line get someone to pump brake pedal while ur holding line in a jar keep refilling the brake resivoir so no air gets in, once the master is bled front brake side then reattach the origional brake line then remove bleed screw from caliper and let fluid gravity flow down to calliper then bleed the normal way. more than likely your master cylinder has air trapped in the front portion good luck

Jul 01, 2008 | 1996 Chevrolet Blazer

Not finding what you are looking for?
1994 Ford Taurus Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5581 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...