Question about 2003 Chevrolet Silverado 2500HD

1 Answer

Instument cluster failure - 2003 Chevrolet Silverado 2500HD

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

Think there was a recall on this, call dealer

Posted on Aug 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instument panel not working


The cluster itself. If power and ground to cluster are good then it's likely that the cluster needs to be replaced.

Apr 20, 2014 | 2000 Chevrolet Blazer

1 Answer

The ABS light stays on, then the instuments go dead, then the Check Engine light comes on. When I check it with my Checker it says P1698 Error.


re[place instument cluster its an intermitand problem the abs light is probaly because the cluster isnt talking on the buss then it crashes and no one is talking so all the lights come on

Mar 08, 2014 | 1998 Dodge Grand Caravan

1 Answer

Need to cahnge the bulbs in the instument cluster on a 2002 chrysler concorde


Remove dash trim around the cluster to access the screws holding in the cluster. on back side of cluster should be the blade type bulbs.5eccf67a-7e57-48ea-aa2e-67e4dccfc666.jpg

Dec 05, 2013 | 1991 BMW 3 Series

1 Answer

Speedometer and Battery Gauges stopped working. could it be a need to replace fuses or is it a problem with the motors that drive the gauges?


there is a lot of issues with GM instument clusters .I have a 2004 chevy cavalier in my shop with the same problem. just replace the instument cluster

Oct 30, 2012 | Cars & Trucks

1 Answer

Does the ECM control the MPH gauge?


well yes but no,the speedometer signal comes from speed sensor in the transmission then goes through the ecm/pcm via the tcm (transmission control module, then on to your speedo,if the speed sensor goes bad usually the speedometer will work crazy if not at all also the instument clusters also go bad causing failure too find a new tech dude

Feb 28, 2012 | 1998 Dodge Caravan

1 Answer

My spedometer wasnt working all the time when it did work my transmission would shift fine thought it was speed censor tried to change now my spedometer dont work at all could this been the problem and i...


No,the speed sensor is for calcultions for the ABS brake system.The speedometer problem is an on going problem that GM has with there instument clusters.You'll have to replace the instument cluster to fix the speedometer problem.As for transmission problem i would chenge the fluid and filter if you are having shift problems,if problem still exists after servicing transmission have the shift solenoids checked sounds like they maybe sticking.

May 04, 2011 | 2002 Chevrolet Cavalier Coupe

1 Answer

I have a 1994 ford probe and the speedometor,oil gage,and the mileage dont work fuses are good in the car.Does this mean that its an instument cluster or something else?


its either the cluster, or its not getting power, look in the back for a lose wire if u dont find 1 you probably need a cluster

Feb 22, 2009 | 1998 Jeep Cherokee

1 Answer

Instument Guages


well the issue is youe enitre gauge cluster i do understand that your speedometer is working but it is a cable speedometer not electronic like everything else in the gauge cluster so first i would recomend checking the voltage getting to your gauge cluster then just replace the guagecluster they are really cheap i a salvage and not hard to install at all but the cluster itself is not very comon to go out so make sure you check voltage to it first i wouldnt want you to go through buying and replaceing the cluster and that not fix it

Jan 20, 2009 | 1991 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...