Question about 1995 Ford F250

1 Answer

Removing radio from 95 ford f-250 - 1995 Ford F250

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Ford Master
  • 4,981 Answers

Is there anything here that can help ?

Posted on Aug 10, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Remove dash and replace radio in f250 ford 2011 super duty

just remove the cover from around the radio heater switched ....should just pull off...then you can access the radio to change it

Dec 05, 2016 | 2011 Ford F-250 Super Duty

1 Answer

How do i remove the rear drums for a 95 ford f-250?

Just pull it off

Go to You Tube Video-- if you never worked on
any vehicle before

Mar 21, 2013 | 1995 Ford F250

1 Answer

95 ford f-250 . Is it obd1 or obd 2?

96 was first official year for OBD 2 requirement. But some vehicles got it earlier if a new vehicle was coming out in 94 or 95.

What engine?

Oct 21, 2011 | Ford F-250 Cars & Trucks

1 Answer

How to remove the radio from a f-250 superduty

they sell these two little hooks at walmart that slides in on each side of the radio in these little hole about a inch apart

Sep 12, 2010 | 2005 Ford F 250 Super Duty

1 Answer

How do i remove the factory radio in a 2008 ford f250

remove the instrument panel center panel. 4 screws hold the radio (audio control module) into place. note: if you are replacing the acm with a new ford unit it will need to be reprogrammed at a dealership due to the fact that it requires programmable module installation

Sep 08, 2010 | 2008 Ford F 250 Super Duty 4WD

1 Answer

I need to know how to remove the radio to install a xm radio into it

with ford radios from about 1987-2008 on most models,there is a 2 part tool set,each shaped like a U ,1 for each side of the radio,and it pushes into the holes in the radio,then you angle them outwards and pull on the radio and it will come out.I cant remember where to buy them,either Ford or maybe an autoparts store,not sure.its been years ago for me.

Mar 02, 2010 | 2006 Ford F-250 Super Duty

2 Answers

What is the torque specifications on the main bearings for a ford f-250 7.3 diesel

step 1 is 76 ft lbs step 2 is 96 ft lbs, I hope this helps you?

Oct 08, 2009 | 1988 Ford F 250

1 Answer

Removing radio from 2008 f250

First you will have to remove the bezel around the radio. This bezel will also be from top to bottom. The bezel is snapped into the vehicle. Pry it out very carfully. Clips will be located at the top, middle, and bottom of bezel. Once snapped out, unplug harnesses so that you can easily work with radio and will help with not scrathing bezel. Once the bezel is out of the way, there will be four screws, 7mm or 9/32 use either socket size, that will be holding radio in place. Remove screws and then pull out radio. Use an aftermarket wire harness to make your installation easier. Install bracket and radio using screws removed and resnap bezel in place.

May 27, 2009 | 2008 Ford F 250 Super Duty 4WD

1 Answer

How do i remove the radio in a 2006 ford F-250

yes the tool you need is two pieces of steel that fit into both sides of the radio, there should be two holes on either side...the wires push in and the radio should pop out

Apr 06, 2009 | 2006 Ford F-250 Super Duty

1 Answer

95 f-250 right front stub shaft removal

I think if you put a pry bar behind the knuckle and give it a quick bump it will just pop out it has a ring on the inside that holds it in. Just uses pressure to keep it in place I will look in a few but I am sure that is what to do.

Jan 02, 2009 | 1995 Ford F250

Not finding what you are looking for?
1995 Ford F250 Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides