Question about 1998 Mercury Mountaineer

1 Answer

Whenapplying my brakes just before i get stopped my brakes release and then grab again and relase

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Replace the ABS relay and test the braking again. If the same results are found the ABS module is at fault

Posted on Aug 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New Brakes that keep grabbing when when moving. Pulling up on the brake pedal releases them but that may grab again later on down the road.


Sloppy work or your vehicle needed to be
diagnosed for the issue when you took it in
Pull up on what,parking brake?
Then the cables are rusted & need replacing

Aug 10, 2013 | Cars & Trucks

1 Answer

What exactly would cause left front brake to grab randomly


Year, make and model of your vehicle would help. Do you have any codes in your ABS control module ?

Jun 22, 2017 | 2000 BMW 3 Series

1 Answer

When I turn left my brakes repeatedly grab and release. What could be the cause?


What type of truck is this? Faulty break lines. Too much air in brake lines. Rotors. In need of pads. Leaking calliper.

Feb 04, 2013 | Cars & Trucks

1 Answer

I have a 1990 honda accord ex 2door air in brakes.recently i replaced both claipers because the brakes wouldnt release, theyve since relased but the brake literally has no pressure the brake has to be


Your best bet is to bleed the entire system starting with the wheel farthest from the master cylinder, and working to the closest one.
Also, if you have drum brakes on the rear, make sure they are properly adjusted as poor adjustment will cause a "low" pedal.
The cap you refer to with wires is the resivour fluid level sensor, and the ring keeps fluid in and contaminants out.

Jan 02, 2013 | 1990 Honda Accord

1 Answer

When the anti lock brake light on my 93 lincoln town car comes on, if I am pressing on the brake at the time, makes the brakes grab. It also happens just before the light comes on. I have had the front and...


the abs light on the dash should come on when the abs is working (emergency braking)if it comes on when braking normally(gently)chances are a sensor is gone(replace in pairs,fronts & rears)
abs stops the wheels from locking up in an emergency brake situation,you will feel the grab-release,grab-release on the brake pedal......

Jul 16, 2010 | 1993 Lincoln Town Car

1 Answer

Brake problem


The vacuum release is at fault. It is mounted near the emergency brake pedal. It has a silver round type metal vacuum pod attached to it with a vacuum line going to it.

Apr 04, 2010 | 1999 Cadillac DeVille

1 Answer

I was driving my Sante FE yesterday and stopped at a red light. When I released the break all four brakes where still grabbing. As I was close to home, I kept it in 1st gear and drove back home. At that...


you are right when you mastercylinder related,as you have a very small port (compesating)inside the cylinder and should a small partical enter and block this port the brakefluid cannot push back when releasing the brakes causing the brakes to bind.the cylinder should be removed and cleaned.

Jul 11, 2009 | Hyundai Santa Fe Cars & Trucks

1 Answer

Parking Brake on, Under dash release cable broken


Can you get to any part of the cable? If so, use a pair of pliers to release it until you can replace the cable.

Jan 25, 2009 | 2002 GMC Sierra

1 Answer

Pontiac Grand Prix


the problem your having is that the brake didnt relase undeneath your car but it only happed on the one tire. the way you can fix it is go under the car and you will find a cable that goes to both of the wheels. the cable on thr right rear use a vise grip to grab it and slightly pull to release. once it has released spray the area where the cable goes into the brake housing with WD-40.

that should take care of your problem

tom

Dec 20, 2008 | 2001 Pontiac Grand Prix

Not finding what you are looking for?
1998 Mercury Mountaineer Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...