Question about 1989 Chevrolet S-10 Blazer

1 Answer

Trying to remove oil pan from 1989 chevy 1500 350 eng to replace the gasket can you help me?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,984 Answers

2wd Models

  1. Disconnect the negative battery cable. Drain the engine oil.
  2. Remove the oil dipstick.
  3. If necessary remove the exhaust pipe crossover.
  4. If equipped with automatic transmission, remove the converter housing pan and the transmission oil cooler line retainer from the bracket.
  5. On 1996-98 models, remove the oil filter and if equipped, the oil filter adapter.
  6. If necessary, remove the starter brace and bolt and swing the starter aside.
  7. Remove the strut rods, if equipped.
  8. Remove the oil pan and discard the gaskets.
To install:
  1. Apply a suitable sealant such as GM part number 12346192 or its equivalent to the front cover-to-block joint and to the rear crankshaft seal-to-block joint. Apply the sealant about 1 inch (25mm) in both directions from each of the four corners.
  2. Clean all gasket surfaces and use new gaskets to assemble.
  3. Install new gasket and seals.
  4. Install the oil pan.
  5. On 1988-95 models, tighten the pan bolts to 100 inch lbs. (11 Nm). Tighten the pan nuts to 17 ft. lbs. (23 Nm).
  6. On 1996-98 models, tighten the oil pan nuts and bolts to 18 ft. lbs. (25 Nm).
  7. Install the strut rods, if equipped.
  8. If removed, install starter, starter brace and bolt.
  9. If equipped, install the oil filter adapter.
  10. If removed, install the oil filter.
  11. If equipped with automatic transmission, install the converter housing pan and the transmission oil cooler line retainer to the bracket.
  12. Install the exhaust pipe crossover.
  13. Install the oil dipstick.
  14. Fill the engine with oil and check for leaks.

Posted on Aug 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What would cause an oil leak at the rear of my 2003 Chevy S-10 With 2.2L eng.?


oil pan / rear main seal / head / valve cover
more then likely rear main

Jun 26, 2011 | 2003 Chevrolet S-10

2 Answers

I have no oil pressure on the gauge on the dash board and it is leaking oil under neath the engine what could it be. 97 chevy silverado 2500 4by4


Could be a broken oil pressure sending line or something worse.... Hole in oil pan, broken/missing (blown-off) oil filter.

Sep 27, 2010 | Chevrolet Silverado 2500 Cars & Trucks

1 Answer

Whats the easiest way to remove a oil pan for a 1989 XLT F-150 Lariat


pls specified your engine size and tranmission(2WD/4WD) ............lift the vehicle and drain engine oil, remove all bolts and be carefull for removing oil pan, oil pan gasket is reusable

Jun 26, 2010 | 1989 Ford F 150

1 Answer

I have a 1989 chevy 350 that I am replacing with a used one. I am going to replace the oil pump and oil pan gasket. So my question is..... Is there a pattern or torque specs for bolt tightness when putting...


start from the centre and work outwards(middle to ends)finger tight first then hand tight with a socket and 8inch ratchet.do not overtighten.

Jun 17, 2010 | Cars & Trucks

1 Answer

Replace lower oil cooler line


Basically give the vehicle a transmission oil change with a new filter and gasket. Once oil and pan are removed remove old line with appropriate flare wrench. install new one , replace filter gasket and reinstall pan. Refill with ATF.

Apr 13, 2010 | 1989 GMC Sierra

1 Answer

I replace the oil pan gasket and i had to removed


if you drove it for any length of time you would know if it was workin or not cause you would have a blown engine from no oil

Apr 04, 2010 | 1989 Ford Bronco

1 Answer

I have a 1989 honda accord dx with a oil pan gasket leak and a rear main seal leak, in order to fix the rear main seal leak, does the oil pan and the oil pan gasket need to be removed and does the gasket...


they don't use gaskets on oil sumps its sealant glue and yes u will have to reapply it when you put the sump back on, and what do u mean by main seal? do you mean the head gasket?

Nov 18, 2009 | 1989 Honda Accord 4 Door

1 Answer

How do I change the oil gasket??


Are you talking about the oil pan gasket, valve train cover gasket? Id so on either one you must remove the old gasket an replace it. You can try tightening the bolts some to see if that stops the leak, but if not, the gasket should be replaced.

Oct 21, 2009 | 1989 Cadillac Sedan DeVille

1 Answer

Changing oil pan gasket on 1989 Ford Aerostar


drain the oil from the pan and remove the filter.
Lift the car up and secure it . So it will not roll or fall. Remove the bolts from the pan using a 10 mm or so and a rachet and small extension. There are several bolts all around the pan. Remove the pan and remove the gasket. Clean up the pan and remove all gasket material from the pan. Install the new gasket around the pan and replace back.

Apr 05, 2009 | 1989 Ford Aerostar Cargo

Not finding what you are looking for?
Cars & Trucks Logo

1,126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...