Question about 1986 Toyota Land Cruiser

1 Answer

What are the torque settings for landcruiser hub and axle assembly

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 2,984 Answers

This is for the hub....front hub:

  1. Install the hub with a new gasket and tighten the mounting nuts to 23 ft. lbs. (31 Nm).
  2. Install the bolt and washer and tighten it to 13 ft. lbs. (18 Nm).
  3. Coat the inner hub splines with grease.
  4. Make sure the control handle on the cover is still at FREE (if not automatic), position a new gasket in the cover and install the cover so that the pawl tabs are lines up with the non-toothed portions of the hub body. Tighten the mounting nuts to 7 ft. lbs. (10 Nm).
This is for the rear hub:

To install:
  1. Place the hub on the axle housing and install the outer bearing.
  2. Install the lock plate with the lock plate tab positioned into the groove of the axle housing.
  3. Install and tighten the adjusting nut with the special tool used during removal.
  4. Torque the nut to 43 ft. lbs. (59 Nm). Rotate the hub a few times and retorque the adjusting nut to 43 ft. lbs. (59 Nm).
  5. Loosen the adjusting nut until the hub can be turned by hand.
  6. Tighten the nut a small amount and check the amount of pressure required to rotate the hub using a spring tension gauge.
  7. The recommended rotational torque is 5.7-12.6 lbs. (1984-88: 0.9-7.3 lbs.). Tighten or loosen the adjusting nut as required to obtain this reading.
  8. Align one of the axle housing slots with one of the adjusting nut slots. Install the lock screws into the holes of the adjusting nut which are at right angles to the aligned slots. Torque the lock screws to 35-60 inch lbs.
  9. Recheck the rational torque and install the axle shaft using a new gasket.
  10. Install the wheels and lower the vehicle.

Next post is for axles.

Posted on Aug 07, 2010

  • Greg Bernett
    Greg Bernett Aug 07, 2010

    Do you know if they are full floating axles or semi-floating axles?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front hub torque specs


The torque for the hub bolts is 120 ft. lbs
The torque for the axle nut is 185 ft. lbs.

Dec 29, 2013 | Dodge Cars & Trucks

1 Answer

Front axle wine on landcruiser


There's a possibility that the front wheel bearing/hub assembly is wearing out. When it starts wearing out, it will definitely make a sound like you're describing.

Mar 27, 2013 | Toyota Cars & Trucks

1 Answer

How to assemble a front wheel bearing on a 2003 GMC Sierra 1500 4x4


The front wheel bearing is a hub and bearing assembly. To remove you will.... 1. Remove the tire 2. Remove the axle nut. You can put a punch in the fins of the rotor to keep the assembly from turning while you rmove the nut. You can can do the same thing when you torque the axle nut. 3. Remove the caliper and rotor. 4. Unplug the abs sensor if equipped. 5. Remove the three bolts that hold the hub to the knuckle. 6. Rmove the hub. If you need torque specs let me know and i'll get them for you. It is absolutely critical that you torque the axle nut to the proper spec!

Oct 08, 2011 | Cars & Trucks

1 Answer

How do I rgerplabe how do I replace a front wheel bearing?


TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

Mar 21, 2011 | 1999 Oldsmobile Alero

1 Answer

Procedure for front wheel bearing (hub assembly) replacement


jack up vehicle wheel in question and install jack stand.remove wheel. Unbolt 2 caliper bracket bolts and pry caliper assembly up off brake rotor and hang off to the side with bungee.remove rotor . remove large axle nut. From the back of the hub remove hub bolts most commonly 15mm.Using a slide hammer style wheel puller the hub can be removed. if all you have is a big hammer hit the hub back and forth side to side until it can be removed. Bolt in new hub assembly and torque bolts.Install axle nut and torque. install rotor and caliper. reinstall wheel and torque.

Nov 28, 2010 | 2001 Chrysler Concorde

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

1 Answer

How long does it take to fix front bearings on a 97 dodge caravan? and cost


About an hour a side...This is the whole job and pictures....

The hub and wheel bearing unit is serviced as a complete assembly. Replacement of the front drive hub and bearing assembly can be done without having to remove the steering knuckle from the vehicle. However, if the hub/bearing assembly is frozen to the steering knuckle, removal of the steering knuckle is required.
  1. Disconnect the negative battery cable.
  2. Remove the cotter pin from the end of the stub axle. Remove the nut lock and spring washer. With the brakes applied, loosen, but do NOT remove the axle nut and washer with the vehicle still on the ground or damage to the wheel bearing will result.
  3. Raise and safely support the vehicle. Remove the wheel.
  4. Remove the front brake caliper assembly from the steering knuckle assembly and support from the strut assembly using a strong piece of wire.
    1. Remove the front brake rotor from the hub/bearing assembly.
    2. Remove the retaining nut and washer from the halfshaft stub axle.
    3. Remove the ABS wheel speed sensor from the steering knuckle.
    4. Remove the 4 hub and bearing assembly mounting bolts from behind the steering knuckle.
    5. Remove the hub and bearing assembly from the steering knuckle.
  5. To install:
    1. Thoroughly clean the mating surfaces of the steering knuckle and the hub and bearing assembly of any foreign material or nicks so the surfaces are clean and smooth.
    2. Install the new hub and bearing assembly and tighten the mounting bolts in a crisscross pattern to 45 ft. lbs. (65 Nm). Be sure the hub and bearing assembly is seated squarely against the front steering knuckle.
    3. Install the disc brake rotor.
    4. Install the brake caliper assembly onto the steering knuckle.
    5. Install the axle washer and nut. Tighten but do not torque.
    6. Install the ABS wheel speed sensor.
    7. Install the wheel and lug nuts. Torque the lug nuts, in sequence, to 95 ft. lbs. (129 Nm).
    8. Lower the vehicle. Do NOT roll the vehicle until the axle nut has been properly torqued or damage to the front wheel bearings will result.
    9. With the vehicle's brakes applied, torque the axle nut to 180 ft. lbs. (244 Nm). Install the spring washer, nut lock and a new cotter pin. Wrap the cotter pin prongs tightly around the axle nut lock.
    10. Reconnect the negative battery cable. Check the wheel alignment.

fe8edd6.gif
The hub/bearing assembly is attached to the steering knuckle with four bolts


9733319.gif
Removing a hub/bearing assembly



1867b08.gif
If the hub/bearing is "frozen" to the steering knuckle, separate the ball joint and lightly tap on the hub/bearing from behind



09233ac.gif
The hub/bearing assembly should free itself from the steering knuckle

About $60 a hub.

May 23, 2010 | 1997 Dodge Caravan

1 Answer

Need torque setting for rear hub assembly on 2003 Buick Rendezvous


BEARING TO HUB TO THE AXLE BEAM BOLTS TORQUE IS 63 FT LBS.FOR DRUM BRAKES 96 FT LBS WITH DISC BRAKES.

Apr 18, 2010 | 2003 Buick Rendezvous

1 Answer

Front wheel bearing assembly unit, what tools will i need? size sockets ext the right foot lbs of torque for the axel nut,


TOOLS YOU NEED IS 35 METRIC SOCKET FOR AXLE NUT.USE 6 POINT SOCKET.DONT USE 12 POINT SOCKET.COULD DAMAGE AXLE BOLT EDGES.MAKING IT HARD TO GET OFF.YOU NEED A TORQUE WRENCH WITH THE RANGE OF 200 FT LBS TORQUE.YOU NEED 1/2 BREAK BAR.AND A HUB PULLER.NOW TO LOOSEN AXLE NUT.BEST TO LEAVE TIRE ON WITH CAR WEIGHT ON GROUND TO LOOSEN THE AXLE.BECAUSE ITS GOT 192 FT LBS TORQUE.HARD TO LOOSEN WITH TIRE OFF.192 FT LBS TORQUE IS WHAT YOU TORQUE IT AT.BESURE TO READ INSTRUCTIONS TO NEW HUB BEARING ASSEMBLY. YOUR AXLE NUT TORQUE WILL BE DIFFERENT IF YOU GET A NEW GREY NUT.BECAUSE NUT STRENGHT WILL BE DIFFERENT.IF YOU GET A BLACK NUT WHICH IS HARDER STEEL TORQUE WILL BE 192 FT LBS.YOU NEED A 13 METRIC SWIVEL SOCKET TO GET HUB BEARING BOLTS OFF THEY WILL BE IMPOSSIBLE TO REACH WITH OUT IT.HUB BEARING BOLTS TORQUE IS 62 FT LBS

Mar 16, 2010 | 1999 Oldsmobile Alero

2 Answers

Torque specs


the center bolt for cv axle!103ft-lbs,hub bearing assembly bolts!77ft-lbs

Apr 26, 2009 | Chevrolet Blazer Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

734 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...