Question about 1999 Isuzu Rodeo

1 Answer

Change front rotors ......99 rodeo 2WD - 1999 Isuzu Rodeo

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 2,984 Answers

It is VERY simple:

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove 1/2 of the volume of brake fluid from the master cylinder to prevent overflow when the caliper piston is compressed.
  3. Raise and safely support the vehicle.
  4. Remove the wheel and tire assemblies.
  5. Remove the brake caliper without disconnecting the brake line. Support the caliper with a length of wire. Do not let the caliper hang from the brake hose.
Remove the brake caliper mounting bolt and guide bolt and remove the caliper from the mount. The brackets can be removed for additional work space.

YOU REMOVE #2 IN THE DIAGRAM AND LIFT THE CALIPER OFF OF THE ROTOR.



  1. Unbolt the caliper and suspend it with a piece of wire. Do NOT let the caliper hang by the brake hose.
  2. Remove the rotor.
  3. Installation is the reverse of the removal procedure.change front rotors ......99 rodeo 2WD - b8b7b9d.gif

Posted on Aug 07, 2010

  • 7 more comments 
  • drillsidetra Aug 07, 2010

    how do i change the rotors?

  • Greg Bernett
    Greg Bernett Aug 07, 2010

    Once you remove the caliper, the rotor slides right off. There is nothing holding it in place.



    Please don't rate me or please change your rating. But the rotors honestly slide right off. All the directions are to remove the caliper because it is on top of the rotor.

  • drillsidetra Aug 07, 2010

    wrong.
    there is a LOT more to getting this rotor off. but i can not get it after the removal of the caliper bracket. will the spindle nut have to come off? seems the lug hub is bolted to the rotor?

  • Greg Bernett
    Greg Bernett Aug 07, 2010

    I printed the directions from Chilton's. It may be stuck on due to rust. Spray WD-40 or the equivelant. Let it soak....I am looking at the rotor through the parts store. You DO NOT have to remove the spindle nut. It slides off.

  • Greg Bernett
    Greg Bernett Aug 07, 2010

    If you are removing the rotor to replace it, you may have to use a rubber mallet to loosen it, but it slides off.

  • drillsidetra Aug 07, 2010

    what i see is the rotor attached to the hub by 6 bolts to the back of the hub!

    and by looking at the replacement rotors it proves the rotor is bolted to the back of the hub with the 6 bolts through the hub.
    there is no way this rotor will slip over the hub.

    well you printed a GENERIC direction from chiltons.
    i asked for " replace rotors " and you showed me the calipers .
    so you tell me who was wrong from the start?

    its seems you are just plain wrong. not all rotors "slide" right off. no matter how much wd40 you spray on em!

    i am working on this auto as i type this so i need to see a diagram exploded view of the hub/rotor assembly for a 2WD 1999 rodeo w/v6

  • Greg Bernett
    Greg Bernett Aug 07, 2010

    Which rotor do you have picture 1 or picture 2?



    PICTURE 1










    PICTURE 2




  • drillsidetra Aug 08, 2010

    here is what it looks like. i have finished my project and i thank you for your time.
    rza

    a link to illustration:

    http://www.partswebsite.com/buyisuzuauto...

  • drillsidetra Aug 08, 2010

    sorry
    that link seems to fail when pasted.

    and i did want you to see the illustration so you could see what i am talking about
    sorry
    but i do thank you for your time.
    rza

×

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
honeymokey
  • 3113 Answers

SOURCE: 2002 Isuzu Rodeo 2wd, cant figure out how to

www.myisuzuparts.com

Posted on Apr 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wheel bearing replacement


25 days old.??
car has 4 wheels, must be guess end of car?
2wd or 4wd, yup , be different.
why not just log in to mitchells DIY and end the saga... google it)
ill toss coin for you, lands heads, for front.
front wheel bearings.
2wd
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and support the front end.
  3. Remove the caliper from the anchor plate and suspend it out of the way.
  4. Disconnect the ABS sensor.
  5. Remove the rotor.
  6. Remove the bolts attaching the hub to the knuckle.
  7. Installation is the reverse of removal. Torque the hub bolts to 76 ft. lbs. (103 Nm).
4wd:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Place the transfer case in 2WD.
  3. Raise and support the front end.
  4. Remove the caliper from the anchor plate and suspend it out of the way.
  5. Remove the rotor.
  6. Loosen the caulking around the front driveshaft nuts. Remove the nuts and discard them.
  7. Remove the 4 hub retaining bolts. NOTE If the hub is difficult to remove, install 2 long bolt in the bolt holes and strike them to loosen the hub.
  8. Installation is the reverse of removal. Torque the hub bolts to 76 ft. lbs. (103 Nm). Use new driveshaft nuts, torquing them to 181 ft. lbs. (245 Nm). Apply new caulking. The caulk should be free of cracks when applied.

May 01, 2016 | 2003 Isuzu Rodeo

1 Answer

Cylinder head bolt tightening sequence for isuzu rodeo 1998


1998 Isuzu Truck Rodeo 2WD 2.2L MFI DOHC 4cyl

The Head Bolt Torque

Torque sequence ----------------- front ' 7 3 1 5 9 ' of ' ' engine ' 8 4 2 6 10 ' ----------------- Step 1: torque bolts in sequence to 18 Ft/Lbs Step 2: turn bolts in sequence an additional 90-degrees Step 3: turn bolts in sequence an additional 90-degrees Step 4: turn bolts in sequence an additional 90-degrees recheck final torque in sequence

1998 Isuzu Truck Rodeo 2WD 3.2L MFI DOHC 6cyl

The Head Bolt Torque

Torque sequence -------------- front ' 6 1 3 7 ' of ' ' engine ' 5 2 4 8 ' -------------- Step 1: torque to 20 Ft/Lbs Step 2: torque to 47 Ft/Lbs recheck final torque in sequence

Jan 15, 2013 | 1990 Isuzu Spacecab

1 Answer

Hearing ticking noise from my 1993 isuzu rodeo. Tried oil changes, additives etc. Need to know step by step instructions on replacing lifters.


I had same problem with 99 Isuzu Rodeo LS 3.2 V6. Dealer couldn't find it and many, many other owners experienced same thing. finally found a post where a mechanic (non dealer) changed the idle air control valve. so i tried it, and after 3 years of dealing with the problem, it worked!!! part costs about $40 and very, very easy to change yourself. for the 99, its located in front of engine, so easy access. Good Luck

Feb 18, 2011 | 1993 Isuzu Rodeo

1 Answer

I feel shaking in brake pedal of my 99 rodeo and squealing


Most likely cause is out of round brake rotors.
They will need to be resurfaced or replaced to correct the pulsation you feel in the pedal.
One other cause I can think of is the ABS (anti lock brake system) is activating due to possibly a bad wheel speed sensor.
You can disconnect the power connector at the ABS control unit and road test the vehicle.
If the pulsation is still there than it is not an ABS problem.

Oct 17, 2009 | 1989 Isuzu Pickup 2WD

2 Answers

How to remove and replace front brake rotors chev colorado


Time to buy yourself a good shop manual. You say it is both a 2006 and a 2008.

May 12, 2009 | 2008 Chevrolet Colorado 2WD

1 Answer

Can not find the rear resivor for the wiper fluid on my 99 rodeo


i take it you are talking about for the winshield washer fluid. pop the hatch and it should be located there on the side

Apr 21, 2009 | 1999 Isuzu Rodeo

1 Answer

Torque on 99 rodeo fly wheel


THE TORQUE FOR THESE BOLTS IS 40 FOOT POUNDS

Dec 13, 2008 | 1999 Isuzu Rodeo

2 Answers

99 Isuzu Rodeo 3.2L 2wd Catalytic Converter instructions


you're having the same problem i had with my 99 isuzu rodeo 2 wd 3.2 i paid a muffler guy over $600 to replace those catalytic converters, if you're good at welding you could do the welding yourself after buying the catalytics, basiclly i seen them just cut them off and welded them back on

Nov 26, 2008 | 1999 Isuzu Rodeo

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

607 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...